AT&T 925 User's Manual
Contents
1. Speakerphone Does Not Work The speakerphone might not work well if someone picks up an exten sion phone on the same line The speakerphone will come back on if the handset of the other phone is replaced Other Problems Make sure you have followed all the instructions in this booklet If you continue to have problems call 1 800 722 9125 If you cannot correct the problem disconnect the telephone and refer to the warranty information2. phone press SPEAKER To switch from speakerphone to handset lift the handset NOTE Using an extension phone is not recommended while using the speakerphone Volume Button The VOLUME button adjusts the speaker or the handset during your call Adjusting one does not affect the other When on a call press di to increase volume F to decrease volume Redial The telephone stores in memory the last number you called The number up to 24 digits will remain in the Redial memory until you dial another number To dial the same number again lift the handset or press SPEAKER listen for the dial tone and press FEDAL To erase Redial lift the handset or press SPEAKER press PROGHAM REGAL then again TELEPHONE OPERATION continued Hold The Hold feature allows you to keep a call on the line while you step away from the phone or while some one takes the call on an extension phone When a call is on Hold the red HOLD light flashes and nothing either party says can be heard You cannot access any special features To activate press and release HALD and place the handset back in the cradle When using the speaker phone press and release FOLH To release Hold lift the handset from the cradle or press OR Lift the handset of an extension phone of the line on Hold OR If the handset is not in the cradle press or lift the handset and press HOLD Mute The Mute featu
3. ally with the ringer off Other telephones in your home will still ring they are not affected by the switch Memory Features Capacity This telephone can store up to 32 telephone numbers up to 24 digits long One Touch Dialing The 16 white spaces on the directory card are one touch memory locations You can dial one of these numbers by pressing the memory button next to the number Two Touch Dialing The 16 gray spaces on the directory card are two touch memory locations To dial one of these numbers you must press LOWER then the memory button next to the number Directory Card Remove the plastic cover and the directory card which is on the base Write your telephone numbers in the spaces provided and write the telephone numbers or names that you want to store in each memory location NOTE You may choose to store emergency numbers in memory locations This feature is provided only as a convenience and the manu facturer assumes no responsibility for customer reliance upon the memory feature Programming testing of emergency numbers should be performed in the early morning or late evening off peak hours One Touch Dialing Storing Numbers 1 Lift the handset or press SPEAKER You will hear a dial tone 2 Press and release FAOGAAM 3 Dial the telephone number you want to store You will hear a beep each time you press a button If you want to store a dialing delay in the phone number press wh
4. ere the delay is needed Each time you press PAUSE a three second dialing delay is stored in the dialing sequence Each three second pause counts as one digit memory locations can store up to 24 digits 4 Press and release the memory button where you are storing the number You will hear two beeps to confirm that the number has MEMORY been stored correctly 5 Hang up or press SPEAWER after the number is stored correctly Repeat Steps 1 5 to store another number in memory NOTE Each time you complete stor ing a telephone number by pressing a memory location listen for two quick beeps to confirm that the num ber has been stored in memory If you hear several beeps the number has not been stored hang up and start over An extension phone off the hook can interrupt program ming If you still have trouble see In Case of Difficulty Dialing Numbers 1 Lift the handset or press SPEAKER and listen for a dial tone 2 Press and release a memory button Two Touch Dialing Storing Numbers 1 Lift the handset or press SPEAMER 2 Press PROGHAM 3 Dial the telephone number you want to store You will hear a beep each time you press a button If you want to store a dialing delay in the phone number press where the delay is needed Each time you press PAUSE a three second dialing delay is stored in the dialing sequence Each three second pause counts as one digit memory locations can store
5. i 5 User s Manual for the Speakerphone 925 Fold open this manual for information about this telephone s installation and operation Please read Part 1 Important Product Information included in this package Part 2 1998 Philips Consumer Communications L P All rights reserved Printed in Mexico 848236055 Issue AT amp T NOTE This telephone requires a modular telephone jack Table If you have a wall mounted telephone remove the telephone from the wall and follow these instructions 1 Remove the base 2 Connect line cord to telephone Plug the seven foot line cord into the LINE jack on the bottom of the telephone 3 Attach the base Turn the base so that the larger end of the base is toward the top of the telephone Attach the base by inserting the tabs into the slots Push down on the large end of the base to lock it into place 4 Connect the line cord to your modular jack Plug the free end of the line cord into a modular jack Make sure it snaps firmly into place 5 Connect handset to telephone Plug the coiled cord into the hand set jack on the side of the phone Plug the other end of the coiled cord into the handset and then hang up 6 Check for dial tone Lift the handset and listen for a dial tone If you cannot hear a dial tone turn to In Case of Difficulty INSTALLATION Wall 1 Remove the base 2 Connect the line cord to telephone Do not unbundle line cord Pl
6. k if you have dial pulse service After the telephone is plugged in if you have dial pulse rotary service lift handset and press W l GF To change back to touch tone service lift the handset then press E E E E Hang the handset up for dial mode selection to take effect To switch from pulse to tone dialing during a phone call see Temporary Tone Dialing m Figure 1A Figure 1B Figure 1C TELEPHONE OPERATION Switchhook Handset Accesses memory under handset dialing numbers Directory Card Cover One Touch Memory Locations Access Call Waiting or other services uon f ea Per S SSS RQ J Two Touch Memory Locations Puts a call on hold Mutes a call Redials last call made Speaker Handset Volume Temporary Tone Turns speaker on and makes a call Making and Answering a CallNHandset Lift the handset to make and receive calls as you usually would Making and Answering a CallN Speakerphone NOTE The red speakerphone light will go on when the speakerphone is being used To make a call using the speaker phone press and hold until the speakerphone light comes on wait for dial tone then dial either manual ly or using the memory feature To answer a call using the speaker phone press and hold until the speakerphone light comes on do not lift handset When the call is finished press again to hang up To switch from handset to speaker
7. ling service you cannot dial numbers with the telephone set to touch tone If you just used Temporary Tone leave the handset on the base for a few seconds before making another call IN CASE OF DIFFICULTY Telephone Does Not Ring Make sure the RINGER switch is set in the LO or HI position If there are several other tele phones on the same line try disconnecting some of the other telephones Having too many telephones connected can also create problems such as low ringer volume or impaired sound quality during calls Difficulty Storing Numbers In Memory Review One Touch Dialing and Two Touch Dialing to make sure you are pressing the correct sequence of buttons If you are interrupted by a record ed announcement telling you to hang up or a loud buzzing noise hang up and try to enter the num ber more quickly Try calling the number you want to store into memory When a call is ended press PROGRAM and a memory button or PROGHAM REDWAL and a memory button If someone lifts an extension phone while you are storing numbers in memory programming might be interrupted Make sure all extensions are on hook while storing numbers in memory You might not hear the confirma tion beep if the RECEIVER handset volume is set too low or if you are in a noisy location If the number is more than 24 digits long make sure you follow the directions for Dialing Long Numbers
8. mbine Manual and Memory Dialing Instead of using two memory loca tions you might choose to store only part of a long number You can use memory dialing to dial the stored por tion then dial the other digits manu ally If the stored portion is dialed first wait for dialing to stop before you continue with manual dialing Erasing Numbers To remove any number from memory enter another number in the same location To clear a memory location and leave it empty 1 Lift the handset or press SPEAKER 2 Press and release PRGGHAI 3 Press the memory or LAWER and a button of the memory location you want to clear If this telephone does not work prop erly try the following suggestions before seeking repair assistance No Dial Tone Make sure all plugs are connected properly Inspect the line cord con nections at the modular jack and at the telephone Also inspect the coiled handset cord connection at both ends Make sure Hold is not on Unplug the telephone and connect it to another modular jack If it still does not work and other tele phones in your home are working the problem is with this telephone Call 1 800 722 9125 Call Cannot Be Dialed Or Is Dialed Slowly This product comes set in the touch tone mode Make sure you choose the correct dialing method touch tone dialing will not work if you have dial pulse service See Installation to select the correct dial mode If you have pulse dia
9. re allows you to hear your caller but your caller will not be able to hear anything you say Press and release MUTE the red MUTE light goes on to talk private ly with someone else in the room without the person on the phone hearing you Press and release MUTE again the MUTE light goes off to continue your conversation with the other party Flash The Flash feature is useful if you have subscribed to custom calling services from your local telephone company Press FLASH instead of the switch hook to activate services such as call waiting or three way calling You may have to press other buttons before or after FLASH as explained in the custom calling instructions provid ed by your local telephone company The FLASH button is used only as a substitute for pressing the switchhook Temporary Tone Dialing If you have rotary service you can change from pulse to tone dialing during a call by pressing This is useful if you need to send tone signals for access to telephone banking or long distance services EXAMPLE 1 Dial a number 2 Press and release b all keys pressed after this will send tone signals 3 After you hang up the phone automatically returns to rotary service Digits pressed after W will not be stored in Redial Ringer Volume The RINGER volume switch allows you to turn the telephone ringer OFF or to set it to ring at LO or HI volume You can dial or answer calls norm
10. ug the seven foot line cord into the LINE jack on the underside of the phone Leave enough cord free to connect to the wall jack but keep any excess cord unbundled Store the bundled cord in the open area under the set Attach the base Turn the base so that the larger end of the base is toward the bot tom of the telephone Attach the base by inserting the tabs into the slots Push down on the large end of the base to lock it into place Reverse handset tab To mount the telephone on a wall you must reverse the handset tab This tab holds the handset when you hang up Hold down the switchhook and slide the tab up and out of its slot Figure 1A Turn the tab so that the curved end is up Figure 1B Then insert the tab back into its slot Figure 1C f 5 Connect the line cord to modular wall jack and mount phone onto wall jack Make sure the cord snaps firmly into place Place the phone on the wall jack mounting studs and pull down until it is held securely Follow Steps 5 and 6 under Table Installation Dial Mode Selection This telephone will work with tone or dial pulse rotary service Even when set to dial pulse service the phone can be switched temporarily to tone for access to services that require tone signaling including some tone activated computer systems This product comes set in the touch tone mode Make sure you choose the correct dialing method touch tone dialing will not wor
11. up to 24 digits 4 Press LOWER 5 Press and release the memory button where you are storing the number You will hear two beeps to confirm that the number has been stored correctly 6 Hang up or press SPEANEN after the number is stored correctly Repeat Steps 1 6 to store another number in memory Dialing Numbers 1 Lift the handset or press SPEAKER and listen for a dial tone 2 Press LOWER 3 Press and release a memory button 4 Storing Numbers Just Dialed Whenever you make a telephone call you can store the number you dialed without re entering the digits by hanging up and following the directions for storing a number in One Touch Dialing and Two Touch Dialing and pressing instead of dialing the telephone number Dialing Long Numbers There are two ways to dial telephone numbers that are too long to fit into a memory location Use Two Memory Locations You can store a number of more than 24 digits by dividing it and storing it in two memory locations Follow the directions for storing numbers in One Touch Dialing and Two Touch Dialing to store the number in two memory locations To dial lift the handset or press SPEANER listen for a dial tone then e Press the memory button for the first location or press and a memory button and wait for the dialing to stop e Press and release the memory but ton or press and a memo ry button for the second location Co
Download Pdf Manuals
Related Search