APC BR1200 User's Manual
Contents
1. www apc com Connect Battery User manual Back UPS RS BR1200 BI BR For your security Back UPS RS is provided with the battery cable disconnected The UPS only will work after the cable is connected to the battery terminal N NOTE Small sparks may occur during battery connection Before connecting the battery unplug the Back UPS from wall outlet and also all equipement connected to the UPS This is not a hot swap unit Press the lock that is under the UPS and pull the bezel at the bottom 2 Press the top of the plastic panel and twist the bottom part as shown in the pi In the picture 2 f S j ee S Some resistance to dismount the plastic panel will be noticed This is normal 1 Press the lock that is under the product AZA A Connect the Equipment Place the Back UPS to avoid Direct sunlight Excessive heat Excessive humidity or contact with fluids If you want to use the management function of your Back UPS you shall acquire the communication kit part number AP9937 The supplied cable and software provide automatic file saving and shutdown of the operating system in the case of a sustained power outage If you have the communication kit connect the interface cable to the data port at the Back UPS rear and the other end of the cable to the USB port of your computer Connect Fax modem ADSL phone Connect the battery cable to its terminal positive pole2. http support apc com 990 2767 Rev5 Copyright 2006 American Power Conversion Corp All other trademarks are property of their respective owners APC Back UPS and PowerChute are registered trademarks of American Power Conversion Corp
3. Back UPS RS protects a single line 2 wire fax modem or phone from surges when it is connected through the Back UPS RS as shown Ei Battery Back up plus M Surge Protection These outlets are powered whenever the Back UPS RS is switched ON During a power outage or other utility problems brownouts over voltages these outlets will be powered for a limited time by the Back UPS RS Plug your computer monitor and one other data sensitive device external disk or tape drive into these outlets Data Port Modem Wall Phone FAX Outlet Modem Phone Fax Indicacion Visual Audible Definicion Online Operation is normal Led on Green indicator Beeping 4 times every 30 seconds Beeping once every second UPS will shutdown in one minute Voltage Regulation Yellow indicator for security levels UPS is overloaded disconnect part of the load connected Overload ELed on constant tone Red indicator Check battery Flashing once every Consult troubleshooting section Replacing the battery Fa Wall Outlet j p 1 The utility power is on security levels UPS is running on battery mode and utility power is not available at the power outlet Computer USB port The power from the utility power is above or under the range specified for product UPS is automatically regulating voltage The battery automatic test was not successfully second completed or batte
4. 3 Overloaded verify LED 8 Data Port 4 Power switch 9 Modem Phone Fax Port 5 220V Circuit breaker 10 Wall Outlet When Back UPS indicates the need of replacing battery you should order an APC certified battery pack and proceed as following described A NOTE Small sparks may occur during battery connection 1 Press the lock that is under the UPS and pull the bezel by the bottom 2 Press the top of the plastic panel and twist the bottom part as shown in the picture ji 7 NI P f fas p f ph a CF Some resistance to dismount the plastic panel will be noticed This is normal Turn the cap down and remove it 1 Press the lock that is under the product Remove battery package from the product and replace it UPS is supplying battery power to the load connected to the Battery outlets Before connecting the battery unplug the Back UPS from wall outlet and also all equipement connected to the UPS This is not a hot swap unit Disconnect the central wires and the protection fuses from battery terminals Disconnect the battery and then unscrew the frontal metallic panel te i A Ne yy By i fs E iik SSS h 7 BSS RSE REE i A fe A b i e a SESE REESE PEEL ELL ch hh ee he ee bk BEER EEE ESEEEREESE Reconnect all cables in the inverse order of QO disassembling Engage the metal cap and screw it again Engage the plastic panel superior part and press it s
5. S model number that can be found on rear part of the equipment Use always APC certified batteries Battery must be recycled Please delivery spent batteries St Vas on APC reseller Service Note UPS detailed specifications are available on www apc com br Please DO NOT RETURN Back UPS RS to the place of purchase under any circumstances 1 Consult the Troubleshooting section to eliminate common problems 2 Verify the battery is connected according to Connect the Battery and that the Circuit Breaker is not tripped see Troubleshooting section If you still have questions please contact APC via www apc com br or at one of the phone numbers listed below 3 Before contacting APC please be sure to keep at hands the date purchased UPS model and serial number on rear part of unit 4 If necessary Technical Support Representative will issue a Return Material Authorization Number RMA 5 Pack the unit properly to avoid shipment damage Never use foam beads for packaging Damage sustained in transit is not covered under warranty insuring the package for full value is recom mended APC Contact Information USA Canada 1 800 800 4272 Mexico 222222 222 e eee eee 52 292 0253 52 292 0255 Brazi oe es eee eee ene ene 0800 555 272 Worldwide 1 401 789 5735 Web Site 2 www apc com br Online Technical Support
6. ection UPS automatically shuts down if exceeds 110 of evaluated nominal Circuit breaker resettable of AC input TA 22AV 15 A 115v Battery type Sealed maintenance free lead acid Average life 2 to 4 years depending on number of discharge cycles and enviromental temperature Recharge time Usually 12 hours maximum of 16 hours Net weight 33 Ib 15 0 kg Size HxWxD 7 87x6 50x13 0 inch 20 0x16 5x33 0 cm Operating temperature 32 to 104 F 0 to 40 C Storage temperature 5 to 113 F 15 to 45 C Operating relative humidity 0 to 95 non condensing Operating elevation 0 to 10000 feet 0 to 3000m Input nominal voltage and 86 149 Vac 115V adjustment range 170 260Vac 220V Output voltage and adjustment range 115V 6 Nominal power 1200VA 600 W Connect the battery Consult Connect the Battery section and ensure that is connected on ac outlet Reduce number of equipment connected to UPS outlets Retrip the circuit breaker pushing in it Ensure the equipment switched on UPS outlets are not overloading its capacity Disconnect some equipment if necessary It is a regular operation Reset software Back UPS only can run with battery power during a limited period UPS will be shutdown when available battery power is totally empty Recharge for 12 hour before continue to use them Batteries are recharged when the UPS is connected to power source The Back UPS battery wave outs were designed for comp
7. oftly on rear until it locks Troubleshooting Use the table below to solve minor Back UPS RS installation or operation problems Consult APC on line support or call APC Technical Support for assistance with problems that cannot be resolved using the table below Back UPS RS do not switch on Battery is disconnected and or Unit is not connected to the power source Connected equipment out off Circuit suit is tripped off power Equipment is connected Back UPS is heavily loaded to power PowerChute Personal Edition software executed UPS automatic shutdown Back UPS RS discharged available power of your battery Equipment does not accept sinusoidal waves because of UPS approximation Back UPS beep 4 times Back UPS is using the battery to provide every 30 seconds power to connected equipment The power indicator is on and UPS is overloaded Back UPS RS is buzzing with continuous and short tones The overload verify battery Unit could be not correctly connected indicator flashes and Back UPS RS buzzes with Batteries must be charged continuous and short tones Battery has reached the end of its useful life Specifications Surge capacity 8 outlets 12 Amps including outlet UPS Voltage on battery 115 Vac ms 6 Frequency on battery 60 Hz 1Hz Transfer time 5 ms typical AC surge protection Full time 450 joules Telephone surge protection 1 line 2 wires EMI RFI filter Full time UPS for overload prot
8. ry is disconnected amp Engage the superior part of the panel in the holes and gently push it till it locks i A hy me ye py E WM Mi Pb i Rs Mls Mas hs i a Ms Lithia bh Switch on your Back UPS RS Press the ON OFF switch to power the unit This will initiate an automatic test A single short beep and the green On Line indicator confirms that Back UPS is on and ready to protect your equipments The Back UPS RS is on and ready to provide protection The Back UPS RS should charge for at least 12 hours to ensure sufficient runtime The unit is being charged whenever it is connected to utility power whether the unit is turned ON or OFF In case you have the AP9937 Communication Kit install PowerChute Personal Edition software To install the software insert the CD ROM into the drive and follow the on screen instructions Refer to the software documentation to get further using instructions and functionality Operation indication The Back UPS RS indicates operating status using a combination of audible and visual indicators leds Refer to the Troubleshooting section to get further information y oOo lt pi i i ners SO 3 soan B a lt E ff Back UPS RS a im i7oo SS P lt TA 15A O ot E ay i Wa soo Om a j 7 Frontal Rear Legend 6 110V Circuit breaker 7 Power cable 1 Power LED 2 Tension adjustment LED
9. uters and peripherals not for equipment with motor Back UPS is using the battery to provide power to connected equipment UPS is regularly working You have to save your documents shutdown your equipment and the UPS When the power supply regularly return on you can restart the UPS and your equipment Disconnect non essential equipment Consult Connect the Battery section Recharge UPS at least 12 hours Restarting the UPS an automatic test will be run If the overload verify battery indicator still flashing and beeping a continuous and short tons after the automatic test batteries must be replaced Warranty The standard warranty is 2 years from the date of purchase APC s standard procedure is to replace the original unit with a factory reconditioned unit Customers who must have the original unit back due to assigned asset tags and set depreciation schedules must declare such a need at first contact with APC Technical Support APC will ship the replacement unit once the defective unit is received by the repair department or cross ship upon the provision of a valid credit card number The customer pays for shipping to APC and APC pays ground freight transportation costs back to the customer How to buy a AP9937 Communication Kit The AP9937 Communication Kit can be purchased at any APC dealer or local dealer How to order replacement battery New package battery can be bought from your local dealer Hold your Back UPS R
Download Pdf Manuals
Related Search