AMX HD-RS User's Manual
Contents
1. humidity non condensing Indoor use only Spacing If mounting one control above another leave at least 4 1 2 114mm vertical space between them Wallplates Lutron Claroe and Satin Colorstm wallplates are recommended for best color match and aesthetic appear ance Do not paint controls or wallplates Cleaning To clean wipe with a clean damp cloth DO NOT use any chemical cleaning solutions Wallboxes Lutron recommends using 3 1 2 89mm deep wallboxes for easier installation Several controls may be installed in one multigang wallbox see Multigang Installations page 2 Remotes Use only Lutrone HomeWorks Maestro Remote Dimmers HD RD with HRD HWD 6D 6ND 10D 10ND and 5NE controls Use only Lutron HomeWorks Maestro Remote Switches HD RS with HRD HWD 8ANS controls Up to 9 HD RD or HD RS controls may be used with a HomeWorks Maestro Dimmer or Switch Mechanical 3 or 4 way switches will not work LUTRON Multigang Installations In multigang installations several controls are grouped hori zontally in one multigang wallbox e No derating is required for Remotes When ganging Remotes with dimmers or switches in the same wallbox derating is required for the dimmers or switches See the installation instructions that came with the dimmer or switch for derating requirements Note Controls do not have fins that need to be removed for multigang installations Installation Danger Locate2. 03 P N 043 134 Rev A 93 2605 02 LUTRON
3. HOMEWORKS Designer Style Maestroo Remotes Installation Instructions HD RD RS Please Read Before Installing 120 127 V 50 60 Hz Overview The HD RD Remote Dimmer and the HD RS Remote Switch are for use with HomeWorks Maestro Dimmers and Switches Up to nine HD RD Remote Dimmers may be used with a HomeWorks Wired or RF Maestro Dimmer and up to nine HD RS Remote Switches may be used with a HomeWorks Wired or RF Maestro Switch Important Notes Codes Install in accordance with all local and national elec trical codes HD RD HD RS Danger These controls must not be used to con trol equipment which is not visible from every con trol location They must also not be used to con trol equipment which could create hazardous situ ations such as entrapment if operated accidentally Examples of such equipment which must not be operated by these controls include but are not limited to motorized gates garage doors industrial doors microwave ovens heating pads etc lt is the installer s responsibility to ensure that the equipment being controlled is visible from every control location and that only suitable equipment is connect ed to these controls Overheat Damage To reduce the risk of overheating and possibly damaging other equipment do not install to control receptacles or motor operated appliances Environment Ambient operating temperature 0 40 C 32 104 F 0 90
4. LL OTHER EXPRESS WARRANTIES AND THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO TWO YEARS FROM PUR CHASE THIS WARRANTY DOES NOT COVER THE COST OF INSTALLATION REMOVAL OR REINSTALLATION OR DAMAGE RESULTING FROM MISUSE ABUSE OR IMPROPER OR INCORRECT REPAIR OR DAMAGE FROM IMPROPER WIRING OR INSTALLATION THIS WARRANTY DOES NOT COVER INCIDENTAL OR CONSEQUEN TIAL DAMAGES LUTRON S LIABILITY ON ANY CLAIM FOR DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE MANUFACTURE SALE INSTALLATION DELIVERY OR USE OF THE UNIT SHALL NEVER EXCEED THE PURCHASE PRICE OF THE UNIT This warranty gives you specific legal rights and you may also have other rights which vary from state to state Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Some states do not allow the exclusion or limi tation of incidental or consequential damages so the above limitation or exclusion may not apply to you This product may be covered by one or more of the following U S patents 5 248 919 5 399 940 5 637 930 D353 798 and corresponding foreign patents U S and foreign patents pending Lutron Claro Maestro Hi lume and HomeWorks are registered trademarks and Satin Colors HP 2 4 6 FASS and the HomeWorks Logo are trademarks of Lutron Electronics O 2003 Lutron Electronics Co Inc Lutron Electronics Co Inc 7200 Suter Road Coopersburg PA 18036 1299 Made and printed in the U S A 02
5. and remove fuse or lock circuit A breaker in the OFF position before proceeding Wiring with power ON may result in personal injury Short Circuit Check Check the installation for short cir cuits before installing control s With power OFF install standard mechanical switch es between Hot and load Restore power If lights do not work or a breaker trips check wiring Correct wiring and check again Install con trol s only when short is no longer present Warranty is void if control is turned ON with a shorted circuit 1 Turn power OFF at fusebox or circuit breaker 2 Prepare wires When making wire connections follow the recommended strip lengths and combinations for the supplied wire connectors Note Wire connectors provid ed are suitable for copper wire only 3 Wire controls using Wiring Diagrams 1 and 2 page 3 When using power boosters or interfaces use Wiring Diagrams 3 4 and 5 page 4 Up to nine HD RD or HD RS remotes may be connected to the 6D 6ND 10D 10ND 5NE or 8ANS controls Large Strip insulation 1 2 18mm for 10 AWG 6mm 12 AWG 4mm or 14 AWG 2 5mm Strip insulation 5 8 16mm for 416 AWG 1 5mm or 18 AWG 1 0mm Use to join one or two 12 or 14 AWG sup ply wires with one 10 12 14 16 or 18 AWG control wire 4 Push all wires back into the wallbox and loosely fasten the control to the wallbox using the control mounting screws provided Do not pinch th
6. d then turn OFF Light turns ON and OFF con tinuously Lights don t switch when tap switch is pressed Lights don t switch ON OFF when HD RD or HD RS tap switch is pressed Lights don t switch ON OFF from Keypad Cause and Action Power not present Circuit breaker OFF or tripped Perform Short Circuit Check see page 2 FASSm in the OFF position Move FASS to the ON position by sliding it to the right Check both the dimmer switch and all of the remote dimmers switches Wiring Wires shorted Make sure the blue wires are not grounded or shorted to any other wires Wiring error Check wiring to be sure it agrees with installation instructions and wiring diagrams Lamps burned out Replace lamps Dioded lamps If dioded lamps are being used replace with non dioded lamps Wiring Wiring error Check wiring to be sure it agrees with installation instructions and wiring diagrams Tapswitch stuck Tapswitch stuck at another location Check to see that tapswitches are not sticking for all control loca tions in the circuit Load is less than minimum load requirement Make sure the load connected to the dimmer or switch meets the appropriate minimum load require ment for that control See Load Specifications in the Installation Instructions for the dimmer or switch Wiring Wires shorted Make sure the blue wires are not grounded or shorted to any other wires Wiring error Check wiring to be sure i
7. e wires 5 Attach Lutron Claros or Satin Colorst wallplate adapter and wallplate a Loosely install control mounting screws b Tighten wallplate adapter mounting screws snug c Tighten control mounting screws until wallplate adapter is flush to wall do not over tighten d Snap wallplate onto wallplate adapter and verify that control is not submerged e If control is submerged loosen mounting screws appropriately 6 Complete wiring for all dimmers switches and remotes in this circuit 7 Restore power Check for correct local operation see Local Operation page 5 Mounting Diagram Included Wire Connectors 4 namm Mounting Screws 2 am Wallplate Adapter purchased separately Control a Mounting Mounting Screws Screws a oe rin 1 Al 7 i A IN l l I 33 UB 1 1 o l Wallbox i 1 i 9 i Control i 1 i i I l l l l I I I I I LUTRON Wiring Diagram 1 Multi Location Installation 6D 10D with HD RD Remote Dimmer Dimmer Remote Dimmer Hot Black Red Black gt Red Black X Lighting Load 120 127VAC 50 60Hz Green Neutral Wiring Diagram 2 Multi Location Installation with Neutral 6ND 10ND 5NE with HD RD 8ANS with HD RS Remote Remote Dimmer Dimmer Switch Dimmer Switch Switch Hot Q Black Red Black Red Black az m Lighting _ Load 120 127VAC Green Blue Green Blue Gre
8. en 50 60Hz ak E L Neutral U 1 Up to 9 HomeWorkse Maestros Remote Dimmers Switches may be connected to the HomeWorks Maestro Dimmer Switch Total Blue wire length may be up to 250 76m Switches 2 Remote Dimmers Switches must be connected on the Line side of a multi location installation when used with Neutral wire Dimmers or LUTRON Wiring Diagram 3 Installation with Power NGRX PB Booster or ELV Interface Remote or Dimmer Dimmer ELVI 1000 6ND 10ND with HD RD Hot Live Lighting Load 120 127VAC 50 60 Hz Neutral Wiring Diagram 4 Installation with Fluorescent Dimming Ballast Interface Remote 6ND 10ND with HD RD Dimmer Dimmer FDBI 16A 120 Lutron Hi lume Fluorescent Dimming Ballast s Hot Live 120 127VAC 50 60 Hz Neutral Wiring Diagram 5 Installation with Neutral and E Hi Power Module eee 6ND 10ND with HD RD I HP 2 4 61m 8ANS with HD RS o Hi Power Module Lighting Load Remote Dimmer Switch Dimmer Switch Load Control Terminals Terminals Ni H DH SH Load Circuit E Control Circuit Neutra 120 277VAC Hot Live 50 60 Hz Hot Live Neutral 120 127VAC 50 60 Hz 1 Up to 9 HomeWorkse Maestros Remote Dimmers Switches may be connected to the HomeWorks Maes
9. t agrees with installation instructions and wiring diagrams Wiring Wires shorted Make sure the blue wires are not grounded or shorted to any other wires e Wiring error Check wiring to be sure it agrees with installation instructions and wiring diagrams Improper programming Check programming in HomeWorkss Utility Wiring Wires shorted Make sure the blue wires are not grounded or shorted to any other wires Wiring error Check wiring to be sure it agrees with installation instructions and wiring diagrams LUTRON Notes LUTRON Technical and Sales Assistance If you need assistance call the toll free Lutron Technical Support Center Please provide exact model number when calling 800 523 9466 U S A Canada and the Caribbean Other countries call Tel 610 282 3800 Fax 610 282 3090 Visit our Web site at www lutron com LIMITED WARRANTY Lutron will at its option repair or replace any unit that is defective in materials or manufac ture within two years after purchase For warranty service return unit to place of purchase or mail to Lutron at 7200 Suter Rd Coopersburg PA 18036 1299 postage pre paid Telephone the Lutron Technical Support Center toll free at 800 523 9466 After the two year period a pro rated warranty applies to this product until eight years after the purchase For more infor mation regarding this warranty contact your Lutron representative THIS WARRANTY IS IN LIEU OF A
10. tro Dimmer Switch Total blue wire length may be up to 250 ft 76m 2 Remote Dimmers Switches must be connected on the Line side of a multi location installation when used with Neutral wire Dimmers or Switches LUTRON Local Operation Pressing the Tapswitch on any Dimmer Switch or Remote will alternately turn the lights ON and OFF For HD RD the ON level will be the level previously set using the Dimming Rocker Press and hold the top or bottom of the Dimming Rocker to raise or lower the light level Double tapping the Tapswitch on the HD RD will turn the lights ON to full Pressing and holding the Tapswitch for 1 2 second while ON activates a 10 second long fade to off Remote Dimmer Operation Tapswitch fl on off Dimming Rocker Press to Brighten Press to Dim N PASS OFF ON Front Accessible Service Switch Remote Switch Operation Tapswitch Tap on off NX FASS OFF ON Front Accessible Service Switch LUTRON Lamp Replacement For routine lamp replacement remove power from the fixture s by sliding the Front Accessible Service Switch FASS to the OFF position left After replacing lamps slide the FASS back to the ON position right to restore power Danger For any procedure other than routine lamp replacement power must be disconnected at the main electrical panel Troubleshooting Guide Symptom No lights at all Lights turn ON when tap switch is presse
Download Pdf Manuals
Related Search