American Standard Town Square Pressure Balance Bath/Shower Fitting 2555.602 User's Manual
Contents
1. GAIN ACCESS TO VALVE FOR SERVICING Pull INDEX CAP unscrew HANDLE SCREW and pull HANDLE off valve stem Remove two SCREWS holding ESCUTCHEON and remove ESCUTCHEON Remove COVER by pulling straight out Shut off water supply by either closing off main water supply or closing off the hot and cold CHECK STOPS on valve if present VALVE LEAKS WHEN SHUT OFF Remove CARTRIDGE 1 by removing CARTRIDGE SCREWS 2 Remove three SCREWS 3 from FIXATION RING 4 and pull out PRESSURE BALANCING 5 unit Clean SEALS 9 on base of CARTRIDGE 1 Check base of PRESSURE BALANCING UNIT 5 and clean O RINGS 6 Remove CAPS 7 and check O RINGS on inside of CAPS 7 Clean inside sealing surfaces of VALVE BODY 8 Re assemble PRESSURE BALANCING UNIT 5 and CARTRIDGE 1 Tighten all screws Turn on water supply and see above for installing TRIM and HANDLE UNABLE TO MAINTAIN CONSTANT TEMPERATURE Remove PRESSURE BALANCE UNIT 5 Remove CAPS 7 and clean valve thoroughly Examine balancing unit and check condition of O ring on end of piston Piston should move back and forth Order Repair Part M952100 0070A if balancing unit is defective Replace CAPS 7 and install PRESSURE BALANCE UNIT 5 Make sure inlets line up with two holes in bottom of casting Top flange should butt up against top of casting BACK TO BACK INSTALLATION Remove PRESSURE BALANCE UNIT 5 Rotate PRESSURE BALANCE UNIT 5 180 so that the inlets face up and the large outlet por2. Installation Instructions TOWNSQUARE 2555 602 PRESSURE BALANCING BATH AND SHOWER Built in Diverter for TUB FILLER with EverClean Finish Congratulations on purchasing your American Standard faucet with EverClean finish found only on American Standard faucets EverClean Finish One wipe effortlessly removes spots Eliminates the need for cleaners and scrubbing e Permanent surface protectant remains beautiful Certified to comply with ANSI A112 18 1 for the life of the faucet EverClean available on Polished Chrome Satin Nickel M968789 Rev 1 2 Stainless Steel Polished Brass or any combination of these finishes To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Required Tools ROUGHING IN DIMENSIONS To assure proper positioning in relation to wall note roughing in dimensions 3 1 5 8 TO 3 1 4 ne A FINISHED WALL gt Phillips Screwdriver gt OPTIONAL TO Flat Blade Screwdriver FINISHED FLOOR USUALLY BETWEEN 65 AND 78 M OUTLETS 1 2 NPT Channel Locks INLETS 1 2 NPT THREADED INLETS STOPS Adjustable Wrench BOTTOM OF TUB ROUGHING IN CAUTION Turn off water at main supply When soldering remove PLASTER GUARD CARTRIDGES and CHECK STOPS IF PRESENT When finished soldering flush valve body replace cartri
3. dges check stops if present and plaster guard to continue installation Use thread sealant or Teflon tape on threaded connections If the valve is installed on a fiberglass See Roughing in diagram before starting or other thin wall application the C PLASTER GUARD 4 can be used as a support onnections are S dels netede nal 1 2 female NPT for threaded inlets eth pans anon ie ean a naa a Drill two additional 1 holes to all Connect RISER PIPE 1 to MANIFOLD 2 aes ne Peer Wiest ener een roe top outlet marked SHA Remove PLASTER GUARD 4 rotate 180 Connect TUB FILLER PIPE 3 at bottom so that indicated screw holes fit MANIFOLD 2 outlet marked TUB Push CAP on valve place ESCUTCHEON on and For proper positioning the finished wall attach with screws must be within side wall of PLASTER Connect hot and cold water supplies GUARD 4 Cap off shower pipe 5 and tub filler pipe 6 For support use pipe BRACES 7 secured to wooden braces With valve turned off turn on water supplies Check for leaks INSTALL DIVERTER DIVERTER When finished tiling the wall remove PLASTER GUARD 1 g k Remove two screws that secure the DIVERTER LID 2 and remove Lid Inspect the inside surface of diverter port A Diverter port must be free of any dirt Clean if necessary o Install DIVERTER 3 with SCREWS 4 removed from DIVERTER LID 2 Operate DIVERTER 3 DIVERTER 3 should slide in and out smoo
4. t faces down Push PRESSURE BALANCE UNIT 5 in casting make sure inlets line up with holes in bottom of casting Top flange should butt up against top of casting m Reassemble FIXATION RING 4 and CARTRIDGE 1 ROTATE 180 LARGE SAIRE A INLETS BACK TO BACK INSTALLATION 7 EverClean Finish Care Instructions American Standard s EverClean finish will wipe clean with a soft dry cloth A soft cloth with clean water may also be used if desired No additional cleaning products are required DO NOT USE Soaps acid polish abrasives harsh cleaners or a cloth with a coarse surface M968789 Rev 1 2
5. thly Push on DIVERTER COVER 5 INSTALL TRIM Push CAP 1 over VALVE CARTRIDGE 2 Mount ESCUTCHEON 3 and gasket to valve body with SCREWS 4 Remove PIPE CAPS 5 from shower pipe and tub filler pipe Install SHOWER ARM 6 and SHOWER HEAD 7 Install TUB FILLER SPOUT 8 CAUTION Protect finish on SHOWER ARM By restricting HANDLE rotation and limiting the amount of hot SHOWER HEAD and TUB SPOUT when installing water allowed to mix with the cold the HOT LIMIT SAFETY STOP 1 reduces risk of accidentalscalding To set the maximum hot water temperature of your faucet all you need to do is adjust the setting on the HOT LIMIT SAFETY STOP 1 Turn CARTRIDGE STEM 2 to the OFF position coldest setting before making adjustment to HOT LIMIT STOP 1 Use a flat blade screwdriver to pry free the HOT LIMIT SAFETY STOP 1 Pull forward and rotate counterclockwise one number to limit hot water temperature Use ARROW 3 on CARTRIDGE 4 and NUMBERS 5 on HOT LIMIT STOP 1 for indication SS ZW S 013579111315 Smaller Numbers a a fe Larger Numbers 01357 9 11 13 15 M968789 Rev 1 2 5 INSTALL HANDLE Install HANDLE BUSHING 1 onto CAP 2 Find correct position of HANDLE 3 and push HANDLE 3 onto VALVE STEM 4 Install HANDLE SCREW 5 and push in INDEX CAP 6 Check proper operation of HANDLE Screw on DIVERTER KNOB 7 D TO
Download Pdf Manuals
Related Search