American Standard Ranaissance El Total Toilet 2446 User's Manual
Contents
1. 3 7301186 100 Rev C INSTRUCTIONS TO INSTALL TOILET SEAT Place seat on bowl Be careful to Attach the nut from below center hinge over holes in bowl TOILET SEAT CARE AND CLEANING When cleaning your toilet seat wash it with mild soapy water rinse the seat thoroughly with clear water and dry with a soft cloth Avoid detergents disinfectants or cleaning products in aerosol cans NEVER use abrasive scouring powders on your seat Some bathroom chemicals and cosmetics may damage the seat s finish After installation check the tightness of the bolts from time to Use a screwdriver to tighten bolt Close the hinge covers 3 l time to ensure a tight fit NOTE Pictures are representative and may not exactly depict the flush valve TROUBLESHOOTING IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK SLOWLY repeat Step 13 IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF NON USE it is a signal you are wasting water because e The end of the refill tube is inserted into overflow pipe below water level in tank Attach refill tube to overflow pipe using S clip provided e The flush valve is leaking because it s worn dirty or misaligned with tank ball or flapper replace with a new flapper IF FILL VALVE WON T TURN ON OR SHUT OFF or REFILL OF TANK WATER IS SLOW after valve has been in use for some time Fluidmaster Model 242 Replacement Seal may be needed ae e While holding a e Replace TOP by engaging2. REGON INSTALL CLOSET BOLTS Install closet bolts in flange channel and slide FLOOR into place parallel to wall NUT TAPERED fo WASHER CLOSET we POSITION TOILET ON FLANGE a Unplug floor waste opening and install toilet on closet flange so bolts project through mounting holes b Loosely install retainer washers and nuts Side of washers marked THIS SIDE UP must face up INSTALL WAX SEAL Invert toilet on floor cushion to prevent damage and install wax ring evenly around waste flange horn with tapered end of ring facing toilet Apply a thin bead of sealant around toilet base Product names listed herein are trademarks of AS America Inc AS America Inc 2008 7301186 100 Rev C USE FUTURE R F O SAVE RUBBER RUBBER GASKET BOLT CAP CLOSET BOLT INSTALL TANK WASHER NUT a Install large rubber gasket over INSTALL TOILET a Position toilet squarely to wall and with a rocking motion press bowl down fully on wax ring and flange Alternately tighten nuts until toilet is firmly seated on floor A CAUTION DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED b Install caps on washers If necessary cut bolt height to size before installing caps c Smooth off the bead of sealant around base Remove excess sealant t INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer s directions Before continuing determine the type of water supply
3. from system container over the lugs and rotating 1 8 turn Make sure water supply uncapped VALVE to clockwise MAKE Go to our website at www fluidmaster com for more is off Remove valve TOP prevent splashing turn CERTAIN TIP IS TURNED solutions to toilet problems by lifting arm and rotating water Supply on angoli TO THE TOGKED For troubleshooting information please contact a few times Leave POSITION VALVE MAY top and arm 1 8 turn g A water supply off NOT TURN ON IF TOP IS counterclockwise pressing NOT FULI V TURNED TO Fluidmaster me Conn slighty on Gap THE LOCKED POSITION 30800 Rancho Viejo Road San Juan Capistrano CA 92675 949 728 2000 800 631 2011 GUARANTEE This Fluidmaster product is guaranteed to be free from defective materials and www fluidmaster com workmanship for a period of one year Units returned to Fluidmaster will be replaced without charge 2001 Fluidmaster Inc Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products Fluidmaster Di Hegistoted egeman NFIdmosten Me shall not be responsible or liable for any damages caused by products used with Fluidmaster valves that were not manufactured by Fluidmaster Inc 7301186 100 Rev C TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Does not flush Water supply valve closed Supply line blocked Flush valve chain too loose or disconnected Sand or debris lodged in water con
4. and nuts With tank parallel to wall alternately tighten nuts until tank is snugged down evenly against bowl surface A CAUTION DO NOT OVERTIGHTEN NUTS MORE THAN REQUIRED FOR A SNUG FIT With correct washers in place see Step 9a tighten COUPLING NUT 1 4 turn beyond hand tight DO NOT OVERTIGHTEN A WARNING Do not use plumber s putty pipe dope or any other sealant on the water supply connection to this tank If the connection leaks after hand tightening replace the supply line If the connection continues to leak with the new supply line replace the fill valve Warranty is void if any type of sealant is used on the water supply connection 7301186 100 Rev C ADJUSTMENTS a Adjust water level Water level should be adjusted to level indicated CRITICAL LEVEL lt i MARK CLS on tank by adjusting float cup OVERFLOW PIPE See Step 11 for water level adjustment method b If bowl fails to siphon an adjustment may be required with the lift chain 3 Simply remove the bead chain from WERE S the retainment clip see Fig 10A e A ENT og and take up slack on the chain and reinsert on lift rod Make sure the chain is not too taught Turn on water supply Submerge the FLOAT CUP under the water for 30 seconds Adjust the water to desired level by turning CONE WASHER SA WATER LEVEL ADJUSTMENT PARTS FOR WATER CONNECTION ROD and m
5. INSTALLATION INSTRUCTIONS American Standard Style That Works Better RENAISSANCE EL TOTAL TOILET 2446 COLONY 2388 2399 2359 SONOMA 2454 Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure this product is installed properly please read these instructions carefully before you begin Certain installations may require professional help Also be sure your installation conforms to local codes A CAUTION PRODUCT IS FRAGILE TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE NOTE Pictures may not exactly define contour of china and components RECOMMENDED TOOLS AND MATERIALS Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure Hacksaw Wax Ring Gasket Flexible Supply Tube Closet Bolts Carpenters Level REMOVE OLD TOILET Close toilet supply valve and flush tank completely Towel or sponge remaining water from tank and bowl Disconnect and remove supply line NOTE f replacing valve first shut off main water supply Remove old mounting hardware remove toilet and plug floor waste opening to prevent escaping sewer gases Remove closet bolts from flange and clean away old wax putty etc from base area NOTE Mounting surface must be clean and level before new toilet is installed ROUGHING IN DIMENSIONS NOTE Distance from wall to closet flange centerline must be as listed below A 12 305mm FINISHED WALL CLOSET FLANGE CLOSET BOLTS SUPPLY AS
6. connecation you have from the chart below and use the appropriate assembly parts required to properly reconnect the water supply DO NOT use plumber s putty to seal these fittings METAL COPPER FLARED TUBING METAL FLANGED TUBING E LOCK NUT N LOCK NUT CONE gt EXISTING lt WASHER WASHER EXISTING COUPLING NUT COUPLING NUT WATER SHUT OFF These parts must be used as illustrated to insure water tight connection Use of existing coupling nut may result in water leakage Water supply tube or pipe must extend at least 1 2 inside threaded shank of valve does not apply to flanged tubing Use existing coupling nut and washer CAUTION DO NOT USE CONE WASHER WITH PLASTIC SUPPLY LINE METAL SPIRAL TUBING A Lock NUT EXISTING COUPLING CONE NUT WASHER COUPLING NUT VINYL BRAIDED CONNECTOR LOCK NUT WATER SHUT OFF WATER SHUT OFF Use existing spiral cone washer Fluidmaster cone washer may not seal completely on spiral type supply line Captive cone washers already included No additional washers needed CAUTION Overtightening of LOCK NUT or COUPLING NUT could result in breakage and potential flooding threaded outlet on bottom of tank and lower tank onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening Insert tank mounting bolts and rubber washers from inside tank through mounting holes and secure with metal washers
7. oving FLOAT CUP coupuno wur T eas up or down I CARE AND CLEANING When cleaning your toilet wash it with mild soapy water rinse thoroughly with clear water and dry with a soft cloth Avoid detergents disinfectants or cleaning products in aerosol cans NEVER use abrasive scouring powders or abrasive pads on your toilet seat Some bathroom chemicals and cosmetics may damage the seat s finish A WARNING Do not use in tank cleaners Products containing chlorine calcium hypochlorite can seriously damage fittings in the tank This damage can cause leakage and property damage American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine calcium hypochlorite REPAIR PARTS LIST Repair parts are determined by toilet tank number which can be found marked inside tank NOTE XXX represents color or trim finish options Specify when ordering PART NO DESCRIPTION 735076 400 XXX 4037 TANK COVER 735098 400 XXX 4392 TANK COVER 738565 433 0070A FLUIDMASTER 400A VALVE 738570 1030A FLUIDMASTER REFILL TUBE 7381009 0070A FLUIDMASTER REFILL CLIP 7381007 402 0070A FLUIDMASTER FLUSHVALVE 7381007 404 0070A FLUIDMASTER FLUSHVALVE 730512 0070A TANK COUPLING KIT 232 7381024 400 0070A FLUIDMASTER FLAPPER ASSEMBLY 7381024 402 0070A FLUIDMASTER FLAPPER ASSEMBLY 047192 XXX0A TRIP LEVER ASSEMBLY LH 034783 XXX0A BOLT CAP KIT 128 5329 XXX SEAT
8. plumbing product within one year after its initial purchase confirms that it is defective in materials or workmanship American Standard will repair or at its option exchange the product for a similar model This warranty does not apply to local building code compliance Since local building codes vary considerably the purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before installation This warranty shall be void if the product has been moved from its initial place of installation if it has been subjected to faulty maintenance abuse misuse accident or other damage if it was not installed in accordance with American Standard s instructions or if it has been modified in a manner inconsistent with the product as shipped by American Standard American Standard s option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation nor shall American Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product all of which are expressly excluded from this warranty Some states or provinces do not allow the exclusion or limitation of implied warranties so this exclusion may not apply to you This warranty gives you specific legal rights You may have other statutory rights that vary from state to state or from province to
9. province in which case this warranty does not affect such statutory rights For service under this warranty it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased or that a service request including a description of the product model and of the defect be sent to the following address In the United States American Standard Brands P O Box 6820 Piscataway New Jersey 08855 Attention Director of Consumer Affairs For residents of the United States warranty information may also be obtained by calling the following toll free number 800 442 1902 www americanstandard us com In Canada AS Canada ULC 2480 Stanfield Rd Mississauga Ontario Canada L4Y 1S2 Toll Free 800 387 0369 www americanstandard ca In Mexico Customer Service Manager AS Maquila S A de C V Via Morelos 330 Col Santa Clara Ecatepec 55540 Edo Mexico www americanstandard com mx 7301186 100 Rev C
10. trol Open valve and allow water to fill tank Shut off water supply disconnect supply line and inspect all gaskets and washers Reassemble Also see Fluidmaster maintenance see step 13 Readjust chain length as required Shut off water supply Remove cap and clean per Step 13 Poor or sluggish flush Bowl water level too low Supply valve partly closed Supply pressure too low Partially clogged trapway and or drain pipe and or vent Check that refill tube is connected to water control and inserted into tank overflow without being kinked or damaged Open supply valve fully Be sure that proper supply tube size is used Remove obstruction Consult a plumber if necessary Normal supply pressure must be at least 20 psi Toilet leaks Poor supply line connection Poor bowl to tank floor connection Review Step 9 of installation procedure Review Step 4 through 7 of installation procedure Toilet does not shut off Flush valve chain too tight holding flush valve open Readjust chain length as needed Review step 10 Flush valve seat and or flapper worn or deformed Replace flapper flush valve assembly as needed Sand or debris lodged in water control Shut off water supply Remove cap and clean per Step 13 AS AMERICA INC AMERICAN STANDARD ONE YEAR LIMITED WARRANTY If inspection of this AS America Inc American Standard
Download Pdf Manuals
Related Search