American Standard PORTSMOUTH 7415.101 User's Manual
Contents
1. Fig B PUTTY IF REQUIRED MOUNTING SURFACE m From below push GASKET 7 and RETAINING WASHER 5 onto MOUNTING STUD 4 Secure Faucet with MOUNTING NUT 6 pulling faucet to front of sink so SUPPLIES 3 rests against DEED RON Before final tightening make sure collar on MOUNTING NUT 6 is seated into RETAINING WASHER 5 Fig C Adjust Faucet so that it is centered Tighten MOUNTING NUT 6 to complete faucet mounting 2 POP UP DRAIN m Remove CLEAR PLASTIC COVER 1 BH Remove CARDBOARD SPACER 2 from under DRAIN POP UP 3 m Tighten TAILPIECE 4 on DRAIN BODY before installing DRAIN BODY Fig B 3 REMOVE FLANGE B Thread FLANGE 1 counter clockwise and remove FLANGE 1 and FOAM GASKET 2 from drain body Fig A B Thread LOCKNUT 3 clockwise to bottom of drain body Push GASKET 4 down against LOCKNUT 3 Fig B INSTALL DRAIN FROM BELOW FIXTURE From under side of SINK OF SINK m Tighten LOCKNUT 4 firmly with Adjustable install DRAIN BODY 1 up Wrench or Channel Locks through drain outlet Note No plumber s putty HY g M or caulk is required The CABLE ATTACHMENT POINT 2 must face towards the rear of the SINK N UTL Install FOAM GASKET 3 and cM FLANGE 4 onto drain body from above SINK and tighten FLANGE 4 firmly FLANGE GASKET AND POP UP KNOB Check DRAIN FLANGE in SINK to ensure that WHITE FOAM GASKET 3 is fully compressed and not visible Fig A2. WHITE FOAM POP UP KNOB 1 must be fully down Fig B GASKET D FLANGE M965016 REV 1 6 7 ATTACH CABLE CONNECTOR W Thread CABLE CONNECTOR 1 clockwise onto DRAIN BODY CONNECTION 2 and hand tighten Fig A Your new POP UP DRAIN installation is now complete Fig B Note Tailpeice on pop up drain is 1 1 4 O D Fig B CHECK OPERATION OF POP UP Operate LIFT KNOB 1 to verify that STOPPER 2 opens and closes Note If STOPPER 2 does not open and close properly then refer to the troubleshooting section of these instructions 9 MAKE WATER SUPPLY AND WASTE CONNECTIONS W Connect FLEXIBLE SUPPLIES 1 2 directly to wall supplies Connection on fitting supplies are 3 8 compression Connect left SUPPLY 1 to Hot Marked with a Red Band and right supply to COLD 2 wall supply Faucet supplies are 2O long from faucet base Note If additional supply length is required installer must i purchase additional parts separately Important If SUPPLY HOSES 1 2 are to long loop as illustrated to avoid kinking Connect 1 1 4 O D tailpiece on POP UP DRAIN to waste outlet OX 20 M965016 REV 1 6 1 0 TEST INSTALLED FITTING With HANDLE 1 in OFF position turn on WATER SUPPLIES 2 and check all connections for leaks m Remove AERATOR 3 Operate HANDLE 1 to flush water lines thoroughly Replace AERATOR 3 CHECK DRAIN CONNECTIONS Operate POP UP KNOB 4 and fill lavatory wi
3. be removable Unlocked Mode Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig H To install the stopper in Unlocked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the Sink and the American Standard logo is facing rear Rotate Stopper slightly if necessary so that the Stopper slides all the way down Fig H Re install the Cam into the Drain rotating the Cam if necessary to make sure it is fully inserted Fig J LOOP TOWARD FRONT OF SINK Re install the Cam Cap making sure the guide teeth are facing a outward If the Cam Cap does not snap into place then rotate DRAIN the Cam to make sure it is fully inserted Fig K Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Unlocked Mode Troublingshooting Guide to complete installation Stopper will be in Unlocked mode and removable INSTALL CAM CAP M965016 REV 1 6 M917161 0070A SET SCREW M962951 YYYOA HANDLE KIT M907063 YYYOA CARTRIDGE COVER M904528 0070A CARTRIDGE NUT A918462 0070A M962810 YYYOA POP UP ROD M962682 0070A CARTRIDGE M952425 YYYOA DRAIN ASSEMBLY M922881 YYYOA AERATOR 911903 0070A SEAL M962492 0070A MOUNTING KIT M91 2452 0070A L CABLE ADAPTER 7420101P ESCUTCHEON AND PUTTY PLATE M919660 0020A 6 TAILPIECE NOT INCLUDED WITH FAUCET PORTSMOUT
4. H Momoblock Lavatory Faucet with Speed Connect Drain MODEL NUMBERS 7415 101 Series D M962544 YYYOA STOPPER ASSEMBLY M952430 0070A 4 CABLE ASSEMBLY r M962457 YYYOA FLANGE ASSEMBLY M922872 0070A CAM SEAT INSERT a M962552 0070A f2 CAM ASSEMBLY o 2 M913207 0070A TAILPIECE INSERT A919661 0020A TAILPIECE e C M962458 0070A DRAIN MOUNTING KIT i No Replace the YYY with appropriate finish code CHROME 002 OIL RUBBED BRONZE 224 SATIN NICKEL PVD 295 HOT LINE FOR HELP For toll free information and answers to your questions call 1 800 442 1902 Weekdays 8 00 a m to 6 00 p m EST IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 Weekdays 8 00 a m to 7 00 p m EST IN MEXICO 01 800 839 1200 Product names listed herein are trademarks of American Standard Inc AS America Inc 2010 M965016 REV 1 6
5. IVES HARSH CLEANERS OR A CLOTH WITH A COARSE SURFACE M965016 REV 1 6 Speed Connect Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the down position Follow CABLE ADJUSTMENT PROCEDURE If Stopper does not raise up fully or sink drains too slowly Follow CABLE ADJUSTMENT PROCEDURE If you need to remove the PD Follow STOPPER REMOVAL PROCEDURE If you would like the ability to remove your Stopper simply by lifting it out of the drain Follow STOPPER INSTALLATION PROCEDURE for Unlocked mode CABLE ADJUSTMENT PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam in the illustration Fig B Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go At this point the Stopper should be in the UP position Fig B C Push DOWN on the Lift Knob to make sure it is fully down Fig C Re attach the Cable to the Drain Body Connection 2 by threading the Cable Connector 1 clockwise onto the Drain Body Connection 2 and hand tighten Fig A Fig B Fig C STOPPER REMOVAL PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled
6. Installation Instructions PORTSMOUTH 7420 101 MONOBLOCK LAVATORY 7415 101 FAUCET with Speed Connect Drain Series 7415 101 Congratulations on purchasing your American Standard faucet with Speed Connect drain a feature found only on American Standard faucets Speed Connect Drain e Fewer parts installs in less time e Never needs adjustment e Guaranteed to seal properly the first time every time Corned er comely wt Nak E181 Your new American Standard faucet is designed to work only with the Speed Connect drain To ensure that your installation proceeds smoothly please read these instructions carefully before you begin M965016 REV 1 6 o eo Screwdriver Channel Locks Adjustable Wrench INSTALL FAUCET CAUTION Turn off hot and cold water 7420 101 amp 7415 101 CAUTION supplies before beginning Recommended tools Installation with ESCUTCHEON PLATE Apply a light bead of plumbers putty to underside of ESCUTCHEON PLATE 8 if mounting surface is uneven Place ESCUTCHEON PLATE 8 onto sink or mounting surface Feed FAUCET SUPPLIES 3 MOUNTING STUD 4 and DRAIN CABLE ASSEMBLY 8 through ESCUTCHEON PLATE 8 and mounting hole of lavatory or mounting surface Fig A Installation less ESCUTCHEON PLATE Seat SEAL 11 into under side of FAUCET BASE 2 Feed FAUCET SUPPLIES 3 MOUNTING STUD 4 and DRAIN CABLE ASSEMBLY 8 through the mounting hole of lavatory or mounting surface
7. as Cam and Cam Cap in the illustration Fig B Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain Fig D Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal Fig E The Stopper can now be removed by lifting it out of the Drain Fig F Mo can REMOVE CAM CAP M965016 REV 1 6 STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways Locked Mode Stopper cannot be removed or Unlock Mode Stopper is removable Locked Mode Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig G To install the stopper in Locked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front Rotate Stopper slightly if necessary so that the Stopper slides all the way down Fig G Re install the Cam into the Drain rotating the Cam if necessary to make sure it is fully inserted Fig J LOOP TOWARD REAR OF SINK Re install the Cam Cap making sure the guide teeth are facing outward If the Cam Cap does not snap into place then rotate DRAIN the Cam to make sure it is fully inserted Fig K Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Locked Mode Troubling Shooting Guide to complete installation Stopper will be Vandal Proof in Locked mode and not
8. th water Check that DRAIN STOPPER 5 makes a good seal and retains water in SINK If DRAIN STOPPER 5 does not seal properly please refer to Troubleshooting section in these instructions Release POP UP KNOB 4 down and check all drain connections and P trap for leaks Tighten if necessary SERVICE CAUTION Turn off hot and cold water supplies before beginning W To remove or replace cartidge Fig A Turn valve to OFF position Remove HANDLE SCREW 2 Pull off HANDLE 3 and CAP 4 a Unthread CARTRIDGE NUT 5 and remove a Pull out CARTEIDGE 6 a Inspect CARTRIDGE 6 and O RING 7 for debris and clean if necessary a Clean MANIFOLD 8 and rinse clean Reinstall CARTRIDGE 6 and O RING 7 onto MANIFLOD 8 a Reinstall CARTRIDGE NUT 5 CAP 4 and HANDLE ASSEMBLY 3 If spout drips operate handle several times from OFF to ON and HOT to COLD position Do not force handles turn only 90 7420 101 ONLY SPOUT CAN BE FIXED OR SWIVEL CONVERT TO A FIXED SPOUT IF DESIRED Fig B To change from swivel to fixed spout proceed as follows m Remove SET SCREW 1 using Hex Wrench supplied VIEW A a Install FIXING SET SCREW 2 using Hex Wrench supplied m Align SPOUT 3 and tighten SET SCREW 2 to secure SPOUT 3 1 2 CARE INSTRUCTIONS DO SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER DRY WITH A SOFT COTTON FLANNEL CLOTH DO NOT DO NOT CLEAN THE PRODUCT WITH SOAPS ACID POLISH ABRAS
Download Pdf Manuals
Related Search