American Standard One 2064.451 User's Manual
Contents
1. 4 onto HANDLE ESCUTCHEON 3 until seated tightly against HANDLE ESCUTCHEON 3 4 DRAIN INSTALLATION Apply a bead of PUTTY to underside of FLANGE on DRAIN BODY 1 Feed DRAIN BODY 1 down through lavatory Assembly GASKET 2 WASHER 3 and LOCKNUT 4 onto DRAIN BODY 1 Tighten LOCKNUT 4 firmly Assembly TAILPIECE 5 to DRAIN BODY 1 M968852 5 SERVICE E To change direction of handle rotation proceed as follows Turn valve to OFF position Thread counter clock wise HANDLE BASE 1 to remove HANDLE ASSEMBLY 2 from ESCUTCHEON BASE 3 a Use a flat blade screw driver to remove SPRING CLIP 4 TO REMOVE a Lift STOP WASHER 5 turn 90 and replace HANDLE a Replace SPRING CLIP 4 A a Reinstall HANDLE ASSEMBLY 2 If spout drips operate handles several times from OFF to ON position Do not force handles turn only 90 6 TEST INSTALLED FAUCET Turn HANDLES to off position Remove AERATOR 1 using TOOL 2 supplied Turn hot and cold water supplies on Operate both HANDLES to flush water lines thoroughly Check spout connections for leaks Check all drain connections for leaks m Turn handles to OFF position Replace AERATOR 1 F EverClean Finish Care Instructions American Standard s EverClean finish will wipe clean with a soft dry cloth A soft cloth with clean water may also be used if desired No additional cleaning productsare required DO NOT USE Soaps a2. Amstrican Standard Installation ONE Instructions WALL MOUNT FAUCET 2064 451 IN WALL LAVATORY FITTING with EverClean Finish Congratulations on purchasing your American Standard faucet with EverClean finish found only on American Standard faucets EverClean Finish One wipe effortlessly removes spots p pa Certified to comply with ASME A112 18 1M Eliminates the need for cleaners and scrubbing U S Patent No 5 819 789 e Permanent surface protectant remains beautiful for the life of the faucet EverClean available on Polished Chrome Satin Nickel Stainless Steel Polished Brass or any combination of these finishes M968852 To ensure that your installation proceeds smoothly please read these instructions carefully before you begin ROUGHING IN DIMENSIONS a g 2 MIN 3 MAX 514mm 76mm al 203mm 4 CROSS A HANDLE N P Y p i 25mm FINISHED DN WALL 1 2 NPT INLETS 2 1 8 D D 54mm FINISHED WALL 2 D 52mm 1 1 4 0 D 82mm 0 D Required Tools N Adjustable Wrench Pipe Wrench j oS Plumbers Putty or R 3 C KC a Caulking SO c Tubing Cutter Channel Locks Teflon Tape Flat Blade Screwdriver 1 INSTALL VALVE BODY CAUTION Turn off hot and cold water supplies before beginning Determine where the finished wall locati
3. cid polish abrasives harsh cleaners or a cloth with a coarse surface M968852
4. on will be This measurement is very important Note The rough in measurement from the finished wall is 2 minimum and 3 maximum This is a 1 tolerance See rough in illustration above Secure FAUCET BODY 1 to cross brace of wall structure at required height using two wood screws V Connect HOT water supply to left VALVE inlet and COLD water supply to oat VALVE inlet Use pipe sealant or Teflon tape for all threaded connections For sweat connections do not make sweat connections directly to valve body Damage to seals and and valve cartridge may occur aaron Turn valves to off position Turn hot and cold supplies on and check fitting connections for leaks Complete wall construction INSTALL WALL SPOUT Remove PLASTER GUARDS 1 from valve bodies Inspect that SPOUT NIPPLE O RING 2 is seated in groove of SPOUT NIPPLE 3 Thread SPOUT MOUNT 4 onto SPOUT NIPPLE 3 Align groove on SPOUT MOUNT 4 with face of finished wall See Figure A Install SEAL 5 into SPOUT ESCUTCHEON 6 Place SPOUT ESCUTCHEON 6 with SEAL 5 onto SPOUT MOUNT 4 Push SPOUT 7 onto SPOUT MOUNT 4 Align SPOUT 7 and tighten SPOUT SET SCREW 8 with 8mm HEX WRENCH 9 supplied Figure A ie INSTALL HANDLES m Turn VALVE STEMS 1 to off position E Place O RING 2 into HANDLE ESCUTCHEON 3 Thread HANDLE ESCUTCHEON 4 onto VALVE 5 until snug against finished wall E Thread HANDLE BASE
Download Pdf Manuals
Related Search