American Standard One 2064.101 User's Manual
Contents
1. Locked mode and not be removable Unlocked Mode Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig H a LOGO gt m To install the stopper in Unlocked mode insert the Stopper into _ the Drain so that the Plastic Loop is facing toward the front of the Q Sink and the American Standard logo is facing rear Rotate Stopper slightly if necessary so that the Stopper slides all the way down Fig H 180 u E Re install the Cam into the Drain rotating the Cam if necessary A to make sure it is fully inserted Fig J 0 LOOP TOWARD FRONT OF SINK m HRe install the Gam Cap making sure the guide teeth are facing or outward If the Cam Cap does not snap into place then rotate DRAIN the Cam to make sure tt Is fully inserted Fig K m Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Unlocked Mode Troublingshooting Guide to complete installation Stopper will be in Unlocked mode and removable INSTALL CAM CAP M9688492. Soaps acid polish abrasives harsh cleaners or a cloth with a coarse surface 4 M968849 SpeedConnect Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the down position e Follow CABLE ADJUSTMENT PROCEDURE If Stopper does not raise up fully or sink drains too slowly e Follow CABLE ADJUSTMENT PROCEDURE If you need to remove the Stopper e Follow STOPPER REMOVAL PROCEDURE If you would like the ability to remove your Stopper simply by lifting it out of the drain e Follow STOPPER INSTALLATION PROCEDURE for Unlocked mode CABLE ADJUSTMENT PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 19 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam in the illustration Fig B Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go At this point the stopper should be in the UP position Fig B C Push DOWN on the Lift Knob to make sure it is fully down Fig C Re attach the Cable to the Drain Body Connection 2 by threading the Cable Connector 91 clockwise onto the Drain Body Connection 2 and hand tighten Fig A STOPPER REMOVAL PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locat
3. Amtricam Standard Installation Instructions ONE 2064 101 MONOBLOCK LAVATORY FAUCET with EverClean Finish amp SpeedConnect Drain Congratulations on purchasing your American Standard faucet with EverClean finish and SpeedConnect drain two features found only on American Standard faucets Certified to comply with ANSI A112 18 1 EverClean Finish SpeedConnect Drain M968849 e One wipe effortlessly removes spots e Fewer parts installs in less time Eliminates the need for cleaners and scrubbing e Never needs adjustment e Permanent surface protectant remains beautiful Guaranteed to seal properly the first time every time for the life of the faucet e EverClean available on Polished Chrome Satin Nickel Stainless Steel Polished Brass or any combination of these finishes Your new American Standard faucet is designed to work only with the SoeedConnect drain To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Required tools Screwdriver Channel Locks Adjustable Wrench Turn off hot and cold water 1 INSTALL FAUCET CAUTION supplies before beginning m Seat SEAL 1 into under side of ESCUTCHEON RING 2 m Seat ESCUTCHEON RING 2 with collar facing up into groove in faucet base M Feed FAUCET SUPPLIES 3 MOUNTING STUD 4 and DRAIN CABLE ASSEMBLY 8 through ESCUTCHEON RING 2 and the Figure A mounting hole of lava
4. R 3 Operate HANDLE 1 to flush water lines thoroughly Replace AERATOR 3 CHECK DRAIN CONNECTIONS Operate POP UP KNOB 4 and fill lavatory with water Check that DRAIN STOPPER 5 makes a good seal and retains water in Sink If DRAIN STOPPER 5 does not seal properly please refer to Troubleshooting section in these instructions Release POP UP KNOB 4 down and check all drain connections and P trap for leaks Tighten if necessary WASTE OUTLET 1 1 SERVICE CAUTION Turn off hot and cold water supplies before beginning m To remove or replace cartidge m Turn valve to OFF position Pull out PLUG BUTTON 1 and remove HANDLE SCREW 2 Pull off HANDLE 3 and CAP 4 Unthread CARTRIDGE NUT 5 and remove a Pull out CARTEIDGE 6 m Inspect CARTRIDGE 6 and O RINGS 7 for debris and clean if necessary Clean MANIFOLD 8 and rinse clean Reinstall CARTRIDGE 6 and O RINGS 7 onto MANIFLOD 8 Reinstall CARTRIDGE NUT 5 CAP 4 and HANDLE ASSEMBLY 3 If spout drips operate handle several times from OFF to ON and HOT to COLD position Do not force handles turn only 90 1 Pd EverClean Finish Care Instructions 1 rf ae 2 5mm HEX KEY to i Go gt INSTALL 5 American Standard s EverClean finish will wipe clean with a soft dry cloth A soft cloth with clean water may also be used if desired No additional cleaning products are required DO NOT USE
5. SINK to ensure that WHITE FOAM GASKET 3 is fully compressed and not visible Fig A WHITE FOAM m POP UP KNOB 1 must be fully down Fig B GASKET RAIN D NOT VISIBLE FLANGE M968849 r ATTACH CABLE CONNECTOR E Thread CABLE CONNECTOR 1 clockwise onto DRAIN BODY CONNECTION 2 and hand tighten Fig A Your new POP UP DRAIN installation is now complete Fig B Note Tailpeice on pop up drain is 1 1 4 O D Fig B 8 CHECK OPERATION OF POP UP E Operate LIFT KNOB 1 to verify that STOPPER 2 opens and closes Note If STOPPER 2 does not open and close properly then refer to the troubleshooting section of these instructions Q MAKE WATER SUPPLY AND WASTE CONNECTIONS E Connect FLEXIBLE SUPPLIES 1 2 directly to wall supplies Connection on fitting supplies are 3 8 compression Connect left SUPPLY 1 to Hot Marked with a Red Band and right supply to COLD 2 wall supply m Faucet supplies are 20 long from faucet base Note If additional supply length is required installer must purchase additional parts separately Important If SUPPLY HOSES 1 2 are to long loop as illustrated to avoid kinking m Connect 1 1 4 O D tailpiece on POP UP DRAIN to APPROX 20 waste outlet BLUE BAND 3 8 COMPRESSION M968849 1 0 TEST INSTALLED FITTING With HANDLE 1 in OFF position turn on WATER SUPPLIES 2 and check all connections for leaks Remove AERATO
6. e the component labeled as Cam and Cam Cap in the illustration Fig B Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain Fig D Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal Fig E The Stopper can now be removed by lifting it out of the Drain Fig F REMOVE CAM CAP M968849 STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways Locked Mode Stopper cannot be removed or Unlock Mode Stopper is removable Locked Mode m Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig G E To install the stopper in Locked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front Rotate stopper slightly if necessary so that the Stopper slides all the way down Fig G E Re install the Cam into the Drain rotating the Cam if necessary to make sure it is fully inserted Fig J jpop TOWARD REAR OF SINK E Re install the Cam Cap making sure the guide teeth are facing or outward If the Cam Cap does not snap into place then rotate DRAIN the Cam to make sure it is fully inserted Fig K m Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Locked Mode Troubling Shooting Guide to complete installation Stopper will be Vandal Proof in
7. tory or mounting surface Figure A E From below push GASKET 7 and RETAINING WASHER 5 onto MOUNTING STUD 4 Secure Faucet with MOUNTING NUT 6 pulling faucet to front of sink so SUPPLIES 3 rests against mounting hole Before final tightening make sure collar on MOUNTING NUT 6 is seated into RETAINING WASHER 5 Figure B GROOVE FAUCET E Adjust Faucet so that it is centered Tighten MOUNTING NUT 6 BASE to complete faucet mounting 4 MOUNTING SURFACE COLLAR ON MOUNTING NUT Figure B Pd POP UP DRAIN Remove CLEAR PLASTIC COVER 1 Remove CARDBOARD SPACER 2 from under DRAIN POP UP 3 Tighten TAILPIECE 4 on DRAIN BODY before installing DRAIN BODY Fig B 3 REMOVE FLANGE E Thread FLANGE 1 counter clockwise and remove FLANGE 1 and FOAM GASKET 2 from drain body Fig A mM Thread LOCKNUT 3 clockwise to bottom of drain body Push GASKET 4 down against LOCKNUT 3 Fig B INSTALL DRAIN FROM BELOW FIXTURE D TIGHTEN LOCKNUT E From under side of SINK Tighten LOCKNUT 1 firmly with Adjustable install DRAIN BODY 1 up Wrench or Channel Locks through drain outlet i Note No plumber s putty or caulk is required The CABLE ATTACHMENT POINT 2 must face towards the rear of the SINK Install FOAM GASKET 3 and FLANGE 4 onto drain body from above SINK and tighten FLANGE 4 firmly FLANGE GASKET AND POP UP KNOB Check DRAIN FLANGE in
Download Pdf Manuals
Related Search