American Standard NEW SAVONA 2097.012 User's Manual
Contents
1. l 473mm 18 1 2 HOLES 140mm 5 1 2 CTR S FINISHED ak INSTALL CLOSET BOLTS 305mm ean Install closet bolts in flange channel turn 90 and slide 12 a 343mm C L OF SUPPLY into place 6 152 mm apart and parallel to wall 13 1 2 7 AS REQUIRED WAX RING SEALANT INSTALL WAX SEAL POSITION TOILET ON FLANGE Invert toilet on floor cushion to prevent damage and a Unplug floor waste opening and install toilet on closet flange so bolts project install wax ring evenly around waste flange horn with through mounting holes tapered end of ring facing toilet Apply a thin bead of b Loosely install retainer washers and nuts Side of washers marked THIS sealant around toilet base SIDE UP must face up Product names listed herein are trademarks of AS America Inc AS America Inc 2009 7301387 100 USE FUTURE R F O SAVE INSTALL TOILET Position toilet squarely to wall and with a rocking motion press bowl down fully on wax ring and flange Alternately tighten nuts until toilet is firmly seated on floor A CAUTION DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED Install bolt covers Make sure that the bolt cover area on the toilet is clean and dry see figure Use a dry piece of cloth or soap and water if needed Take plastic bolt cover and peel the brown protective film off on both ends The adhesive part is now visible and ready to be placed on the toilet see f2. Remove obstruction Consult a plumber if necessary Supply pressure too low Normal supply pressure must be at least 20 psi Toilet leaks Poor supply line connection Review Step 8 of installation procedure Poor bowl to tank floor connection b Review Step 4 through 6 of installation procedure Toilet does not shut off Flush valve chain too tight holding flush valve open Readjust chain length as needed Review step 9 Flush valve seat and or flapper worn or deformed Replace flapper flush valve assembly as needed Sand or debris lodged in water control Shut off water supply Remove cap and clean per Step 12 ONE YEAR LIMITED WARRANTY This limited warranty applies only to the original purchaser and installation of the products In the event of a limited warranty claim proof of purchase will be required save sales receipt For this warranty to become effective the accompanying warranty registration card and proof of purchase must be completed and returned to the address on the warranty registration card within 30 days of purchase If inspection of this AS America Inc American Standard plumbing product inclusive of china and all mechanical components within five years after its initial purchase confirms that it is defective in materials or workmanship American Standard will repair or at its option exchange the product for a similar model This warranty does not apply to local building code
3. INSTALLATION INSTRUCTIONS American Standard NEW SAVONA 1 6 GPF ONE PIECE TOILET Style That Works Better Model 2097 012 Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure this product is installed properly please read these instructions carefully before you begin Certain installations may require professional help Also be sure your installation conforms to local codes A CAUTION PRODUCT IS FRAGILE TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE NOTE Pictures may not exactly define contour of china and components RECOMMENDED TOOLS AND MATERIALS Putty Knife Regular Screwdriver Adjustable Wrench Sealant Tape Measure Hacksaw Wax Ring Gasket Flexible Supply Tube Closet Bolts Carpenters Level REMOVE OLD TOILET Close toilet supply valve and flush tank completely Towel or sponge remaining water from tank and bowl Disconnect and remove supply line NOTE f replacing valve first shut off main water supply Remove old mounting hardware remove toilet and plug floor waste opening to prevent escaping sewer gases Remove closet bolts from flange and clean away old wax putty etc from base area NOTE Mounting surface must be clean and level before new toilet is installed ROUGHING IN DIMENSIONS NOTE Distance from wall to closet flange centerline must be as listed below FINISHED WALL 413mm _ CLOSET oO 16 1 4 FLANGE 23mm 355mm 14 lt CIL OF SEAT POST
4. TION 30800 Rancho Viejo Road GUARANTEE This Fluidmaster product is guaranteed to be free from defective materials and San Juan Capistrano CA 92675 workmanship for a period of one year Units returned to Fluidmaster will be replaced without charge 949 728 2000 800 631 2011 www fluidmaster com Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products Fluidmaster shall not be responsible or liable for any damages caused by products used with Fluidmaster valves 2001 Fluidmaster Inc that were not manufactured by Fluidmaster Inc Registered trademark of Fluidmaster Inc TROUBLESHOOTING GUIDE PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Does not flush Water supply valve closed Open valve and allow water to fill tank Supply line blocked Shut off water supply disconnect supply line and inspect all gaskets and washers Reassemble Also see Fluidmaster maintenance see step 12 Flush valve chain too loose or disconnected Readjust chain length as required Sand or debris lodged in water control Shut off water supply Remove cap and clean per Step 12 Poor or sluggish flush Bowl water level too low Check that refill tube is connected to water control and inserted into tank overflow without being kinked or damaged Supply valve partly closed Open supply valve fully Be sure that proper supply tube size is used Partially clogged trapway and or drain pipe and or vent
5. chain and eR reinsert on lift rod Make sure the chain is not too taught Turn on water supply Submerge the FLOAT CUP under the water for 30 seconds Adjust the water to desired level by turning CONE WASHER S WATER LEVEL ADJUSTMENT PARTS FOR WATER ROD and moving FLOAT CUP etd Glas at a ay rere up or down CARE AND CLEANING When cleaning your toilet wash it with mild soapy water rinse thoroughly with clear water and dry with a soft cloth Avoid detergents disinfectants or cleaning products in aerosol cans NEVER use abrasive scouring powders or abrasive pads on your toilet seat Some bathroom chemicals and cosmetics may damage the seats finish A WARNING Do not use in tank cleaners Products containing chlorine calcium hypochlorite can seriously damage fittings in the tank This damage can cause leakage and property damage American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine calcium hypochlorite FLUIDMASTER WATER CONTROL SEAT AND COVER FLUSH VALVE _ _ INCLUDES MTG KIT TANK COVER FLAPPER g ASSEMBLY g SEAT POST C MTG KIT NEW SAVONA ONE PIECE TOILET REPAIR PARTS LIST NOTE XXX represents color options Specify when ordering COMPONENT DESCRIPTION 735146 400 XXX0A Tank Cover 5205 110 XXX Seat Elongated 730835 XXX Bolt Cap Kit Cover 7381059 200 XXX Trip Lever Right Hand 738565 441 0070A Inle
6. compliance Since local building codes vary considerably the purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before installation This warranty shall be void if the product has been moved from its initial place of installation if it has been subjected to faulty maintenance abuse misuse accident or other damage if it was not installed in accordance with American Standard s instructions or if it has been modified in a manner inconsistent with the product as shipped by American Standard This warranty DOES NOT COVER any damage caused by the use of in tank cleaners American Standard s option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation nor shall American Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product all of which are expressly excluded from this warranty Some states or provinces do not allow the exclusion or limitation of implied warranties so this exclusion may not apply to you This warranty gives you specific legal rights You may have other statutory rights that vary from state to state or from province to province in which case this warranty does not affect such statutory rights For service under this warranty it is suggested that a claim be made through the contractor or dealer from o
7. er tight coupling nut cone washer washers already connection Use of existing and washer Fluidmaster cone included No coupling nut may result in washer may not additional washers water leakage Water supply seal completely on needed tube or pipe must extend at spiral type supply least 1 2 inside threaded line A P shank of valve does not apply With correct washers in place to flanged tubing see Step 8a tighten COUPLING NUT 1 4 turn beyond i CAUTION Overtightening of hand tight DO NOT CAUTION DO NOT USE LOCK NUT or COUPLING NUT OVERTIGHTEN CONE WASHER WITH could result in breakage and PLASTIC SUPPLY LINE potential flooding A WARNING Do not use plumbers putty pipe dope or any other sealant on the water supply connection to this tank If the connection leaks after hand tightening replace the supply line If the connection continues to leak with the new supply line replace the fill valve Warranty is void if any type of sealant is used on the water supply connection s 2s 7301387 100 ARM Nipple REFILL ADJUSTMENTS U Q a Adjust water level Water level should be adjusted to level indicated Ooa ig on tank by adjusting float cup ABOVE a OVERFLOW PIPE st See Step 10 for water level adjustment g 3 method b If bowl fails to siphon an adjustment may be required with the lift chain Simply remove the bead chain from 3 the retainment clip see Fig 9A and ADJUSTMENT amp take up slack on the
8. igure Gently place the bolt cover on the toilet area see picture and if everything is aligned push bolt cover firmly so it remains in place If not aligned you can still take it off and put it back so it is aligned Repeat Step 3 for second bolt cover which is to be placed on opposite side of the toilet After 24 hours the bolt cover adhesive has completely set off and if needed you can remove replace as needed The dual lock technology is now in place Smooth off the bead of sealant around base Remove excess sealant Back Side Peel both protective films off and stick bolt cover to toilet BOLT COVER Front Side FA INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer s directions 8a Before continuing determine the type of water supply connecation you have from the chart below and use the appropriate assembly parts required to properly reconnect the water supply DO NOT use plumber s putty to seal these fittings METAL COPPER METAL FLANGED METAL SPIRAL VINYL BRAIDED FLARED TUBING TUBING TUBING CONNECTOR E LOCK NUT N LOCK NUT N LOCK NUT SPS Lock NUT CONE XS EXISTING EXISTING COUPLING lt WASHER WASHER CONE NUT WASHER COUPLING _ EXISTING COUPLING COUPLING NUT WATER WATER WATER WATER N SHUT OFF SHUT OFF SHUT OFF AN SHUT OFF I r D S p These parts must be used as Use existing Use existing spiral Captive cone illustrated to insure wat
9. r through whom the product was purchased or that a service request including a description of the product model and of the defect be sent to the following address In the United States In Canada In Mexico American Standard Brands AS Canada ULC Customer Service Manager P O Box 6820 2480 Stanfield Rd AS Maauilia Mexico S A de C V Piscataway New Jersey 08855 Mississauga Ontario Via Morelos 330 Attention Director of Consumer Affairs Canada L4Y 1S2 Col Santa Clara For residents of the United States warranty information may also be Toll Free 800 387 0369 Ecatepec 55540 Edo Mexico obtained by calling the following toll free number 800 442 1902 www americanstandard ca www americanstandard com mx www americanstandard us com 4 7301387 100
10. t Valve 738942 1000A Flush Valve 1 6 GPF 738920 0070A Flapper Assembly 1 6 GPF eje je e amp jea je agd 7301387 100 TROUBLESHOOTING IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK SLOWLY repeat Step 12 IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF NON USE it is a signal you are wasting water because e The end of the refill tube is inserted into overflow pipe below water level in tank Attach refill tube to overflow pipe using S clip provided e The flush valve is leaking because it s worn dirty or misaligned with tank ball or flapper replace with a new flapper IF FILL VALVE WON T TURN ON OR SHUT OFF or REFILL OF TANK WATER IS SLOW after valve has been in use for IMPORTANT Always e While holding a e Replace TOP by engaging some time Fluidmaster Model 242 Replacement Seal may be clear sand and rust from container over the lugs and rotating 1 8 turn needed system uncapped VALVE to clockwise MAKE e Make sure water supply is prevent splashing turn CERTAIN TIP IS TURNED Go to our website at www fluidmaster com for more off Remove valve TOP by water supply on and off TO THE LOCKED solutions to toilet problems lifting arm and rotating top a few times Leave POSITION VALVE MAY For troubleshooting information please contact and arm 1 8 turn water supply off NOT TURN ON IF TOP IS counterclockwise pressing NOT FULLY TURNED TO Flu dmaste rime down slightly on cap THE LOCKED POSI
Download Pdf Manuals
Related Search