American Standard Moments 2506.801 User's Manual
Contents
1. 8 from under side of sink Make sure SPOUT 1 is centered in the mounting hole and the slot in the BRASS WASHER 5 faces toward the rear of the sink m Tighten LOCKNUT 7 firmly Fig A g 74 INSTALL VALVE BODIES Fig B 3 m Thread MOUNTING RING NUTS 9 counter clockwise to allow enough space for the thickness of the mounting surface E Adjust the three LOCKING SCREWS 10 so that they extend about 1 2 inch above the MOUNTING RING NUTS 9 Install MOUNTING WASHERS 11 and RUBBER WASHERS 12 onto VALVE BODIES Thread VALVE BODY 14 with red band into the left side hot of the ESCUTCHEON 13 until it s seated against the stop Thread the cold VALVE BODY 14a into the opposite side m Hand tighten the MOUNTING RING NUTS 9 on valve bodies Adjust valve outlets to face the SPOUT SHANK 8 m With a flate blade screwdriver alternetly tighten the three LOCKING SCREWS 10 to secure the valve bodies Make sure there is equal pressure on all LOCKING SCREWS 10 MOUNTING SURFACE Mi 13 ol 14a 12 lt 42 VALVE OUTLET 1 2 JE re x t o 2 1 1 8 MAX 9 P POP UP DRAIN mM Remove CLEAR PLASTIC COVER 1 m Remove CARDBOARD SPACER 2 from under DRAIN POP UP 3 E Tighten TAILPIECE 4 on DRAIN BODY before installing DRAIN BODY Fig B 3 REMOVE FLANGE E Thread FLAN2. ARATELY E Thread TEE BODY 4 to SPOUT SHANK 5 E Thread HOSE CONNECTOR 6 6A to VALVE CONNECTIONS 7 7A E Connect water supply to VALVE BODIES 1 1A with 1 2 IPS FLEXIBLE SUPPLIES 2 or 3 8 0 D BULL NOSE RISERS 3 Use adjustable wrench to tighten connections Do not over tighten Be careful not to kink copper supply when bending Use tubing cutter to cut to proper length E Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant appropriate connectors and COUPLING NUTS E Connect 1 1 4 O D tailpiece on POP UP DRAIN to COUPLING waste outlet NUT 1 2 PIPE THREAD 3 80 3 BULL NOSE RISERS COMPRESSION NUT FERRULE COLD 3 8 COMPRESSION CONNECTION M368946 Rev 1 1 INSTALL HANDLES E Turn VALVE STEMS 1 to the OFF position as shown in illustration NOTE Once the HANDLES 2 are installed they are difficult to remove from the VALVE STEM 1 to make any adjustments Make sure HANDLES 2 are properly aligned before they are installed onto the VALVE STEMS 1 Only push HANDLES 2 completely down into place when alignment is satisfactory Align HANDLES 2 as shown Push HANDLE 2 onto VALVE STEM 9 The HANDLE 2 is installed properly when the top of the handle base is flush with top of ESCUTCHEON 3 1 1 TEST INSTALLED FITTING m With HANDLES 1 in OFF position turn on WATER SUPPLIES 2 and check al
3. BLY MOUNTING Ki IM953006 0070A TEE amp HOSE KIT M952430 0070A CABLE ASSEMBLY M962457 YYYOA FLANGE M952425 YYYOA E ia 024220 0070A F DRAIN ASSEMBLY SUPPLY NUT U M922872 0070A CAM SEAT INSERT a M962552 0070A J Ai CAM ASSEMBLY gt AOA Replace the YYY with appropriate finish code CHROME 002 STAINLESS STEEL 075 lt D M913207 0070A TAILPIECE INSERT lt M919660 0020A 6 TAILPIECE NOT INCLUDED A919661 0020A WITH FAUCET TAILPIECE r M962458 0070A HOT LINE FOR HELP For toll free information and answers to your questions call DRAIN MOUNTING KIT 1 800 442 1902 Weekdays 8 00 a m to 6 00 p m EST IN MEXICO 01 800 839 12 00 IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 Weekdays 8 00 a m to 7 00 p m EST Product names listed herein are trademarks of American Standard Inc American Standard Inc 2007 MS68946 Rev 1 14
4. GE 1 counter clockwise and remove FLANGE 1 and FOAM GASKET 2 from drain body Fig A E Thread LOCKNUT 3 clock wise to bottom of drain body Push GASKET 4 down against LOCKNUT 3 Fig B INSTALL DRAIN FROM BELOW FIXTURE E From under side of SINK SS Tighten LOCKNUT 1 firmly with Adjustable install DRAIN BODY 1 up Wrench or Channel Locks through drain outlet Note No plumber s putty or caulk is required The CABLE ATTACHMENT POINT 2 must face towards the rear of the SINK E Install FOAM GASKET 3 and FLANGE 4 onto drain body from above SINK and tighten FLANGE 4 firmly m Check DRAIN FLANGE in SINK to ensure that WHITE FOAM GASKET 3 is fully compressed and not visible Fig A f i WHITE FOAM m POP UP KNOB 1 must be fully down Fig B GASKET NOT VISIBLE FLANGE M968946 Rev 1 1 r ATTACH CABLE CONNECTOR Thread CABLE CONNECTOR 1 clockwise onto DRAIN BODY CONNECTION 2 and hand tighten Fig A Your new POP UP DRAIN installation is now complete Fig B Note Tailpeice on pop up drain is 1 1 2 O D Fig B 1 1 4 O D 8 CHECK OPERATION OF POP UP Operate LIFT KNOB 1 to verify that STOPPER 2 opens and closes Note If STOPPER 2 does not open and close properly then refer to the troubleshooting section of these instructions MAKE WATER SUPPLY AND WASTE CONNECTIONS NOTE FLEXIBLE SUPPLIES OR BULL NOSE RISERS NOT INCLUDED AND MUST BE PURCHASED SEP
5. Installation Instructions MOMENTS Spread Lavatory Faucet withthe 2906 801 EverClean Finish amp Speed Connect Drain Congratulations on purchasing your American Standard faucet with the EverClean finish and Speed Connect drain two features found only on American Standard faucets EverClean Finish Certified to comply with ANSI A112 18 1 e One wipe effortlessly removes spots a Pier Ud Eliminates the need for cleaners and scrubbing Speed Connect Drain e Permanent surface protectant remains beautiful e Fewer parts installs in less time for the life of the faucet Never needs adjustment EverClean available on Polished Chrome Satin Nickel Guaranteed to seal properly the first time every time Stainless Steel Polished Brass or any combination of these finishes Your new American Standard faucet is designed to work only with the Speed Connect drain To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Recommended tools gt Screwdriver Channel Locks Adjustable Wrench Tubing Cutter 1 INSTALL SPOUT CAUTION Turn off hot and cold water supplies before beginning NOTE No putty required Only use putty under escutcheon if mounting surface is not flat E Insert SPOUT 1 and CABLE CONNECTOR 2 through center hole of ESCUTCHEON 13 and mounting surface 3 mw Assemble RUBBER WASHER 5 BRASS WASHER 6 and LOCKNUT 7 onto SPOUT SHANK
6. either side of the Cam Cap to pry it out from the Drain Fig D Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal Fig E The Stopper can now be removed by lifting it out of the Drain Fig F A CAM REMOVE CAM CAP M968946 Rev 1 1 STOPPER INSTALLATION PROCEDURE The Stopper can be installed two ways Locked Mode Stopper cannot be removed or Unlock Mode Stopper is removable Locked Mode E Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper Fig G E To install the stopper in Locked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the Sink and the American Standard logo is facing front Rotate stopper slightly if necessary so that the Stopper slides all the way down Fig G E Re install the Cam into the Drain rotating the Cam if necessary to make sure tt is fully inserted Fig J LOOP TOWARD REAR OF SINK E Re install the Cam Cap making sure the guide teeth are facing Cor outward If the Cam Cap does not snap into place then rotate DRAIN the Cam to make sure tt Is fully inserted Fig K m Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Locked Mode Troubling Shooting Guide to complete installation Stopper will be Vandal Proof in Locked mode and not be removable Unlocked Mode m Look at the Plastic Loop at the bottom of the St
7. l connections for leaks m m Remove AERATOR 3 Operate both HANDLES 1 to flush water lines thoroughly m Replace AERATOR 3 UY q A oer He T SS 1 Pd CHECK DRAIN CONNECTIONS on C CTO rv l a RRA NAAN lt 5 co d E Operate POP UP KNOB 5 and fill Sink with water Check that DRAIN STOPPER 4 makes a good seal and retains water in Sink If STOPPER 4 does not seal properly please refer to Troubleshooting Guide in these instructions TE m f III INIIINN EI INV WASTE M N E IV Oo Cc r m VV OAA E Release POP UP KNOB 5 down and check all drain connections and P trap for leaks m Tighten if necessary We LETT HOT M NX Io N amp EverClean Finish Care Instructions American Standard s EverClean mM To change direction of handle rotation finish will wipe clean with a soft pone ene dry cloth m Turn valve to OFF position Pull HANDLE 1 A soft cloth with clean water up to remove Remove SCREW 2 and three STEM may also be used if desired No additional cleaning products PIECES 3 Remove SPRING CLIP 4 are required Lift STOP WASHER 5 turn 90 and replace Replace SPRING CLIP 4 DO NOT USE Soaps acid polish abrasives harsh Replace items 3 and SCREW 2 cleaners or a cloth with a Push HANDLES 1 onto valve stem coarse surface M968946 Rev 1 1 Speed Connect Drain Tro
8. opper and notice that the Loop is on one side of the Stopper Fig H m To install the stopper in Unlocked mode insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the Sink and the American Standard logo is facing rear Rotate Stopper slightly if necessary so that the Stopper slides all the way down Fig H E Re install the Cam into the Drain rotating the Cam if necessary to make sure tt is fully inserted Fig J LOOP TOWARD FRONT OF SINK E Re install the Cam Cap making sure the guide teeth are facing I outward If the Cam Cap does not snap into place then rotate DRAIN the Cam to make sure it is fully inserted Fig K m Re attach Cable See CABLE ADJUSTMENT PROCEDURE in Unlocked Mode Troublingshooting Guide to complete installation Stopper will be in Unlocked mode and removable INSTALL CAM CAP M968946 Rev 1 1 American Standard MOMENTS WIDESPREAD LAVATORY FAUCET MODEL NUMBER M962565 YYYOA SPOUT KIT 2506 801 M962568 YYYOA AERATOR a MS962566 YYYOA POP UP ROD M962567 YYYOA HANDLE KIT x see g M962569 YYYOA ESCUTCHEON WITH SA D gt PUTTY PLATE 3 TS M961733 0070A SPOUT MOUNTING KIT M918324 0070A HANDLE SCREW M962570 0070A HANDLE ADAPTER KIT 994053 0070A oat CARTRIDGE SS Ly 15 ee M962544 YYYOA STOPPER M962571 0070A ASSEM
9. ubleshooting Guide If sink does not hold water even though Stopper is in the down position e Follow CABLE ADJUSTMENT PROCEDURE If Stopper does not raise up fully or sink drains too slowly e Follow CABLE ADJUSTMENT PROCEDURE If you need to remove the Stopper e Follow STOPPER REMOVAL PROCEDURE If you would like the ability to remove your Stopper simply by lifting it out of the drain e Follow STOPPER INSTALLATION PROCEDURE for Unlocked made CABLE ADJUSTMENT PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam in the illustration Fig B Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go At this point the Stopper should be in the UP position Fig B C Push DOWN on the Lift Knob to make sure it is fully down Fig C Re attach the Cable to the Drain Body Connection 2 by threading the Cable Connector 1 clockwise onto the Drain Body Connection 2 and hand tighten Fig A STOPPER REMOVAL PROCEDURE Disconnect the Cable from the Drain by threading the Cable Connector 1 counter clockwise Fig A Look at the area on the Drain Body where the Cable was attached and locate the component labeled as Cam and Cam Cap in the illustration Fig B Use fingers or small screwdriver under
Download Pdf Manuals
Related Search