American Standard Enfield Bathtub 2742.020 User's Manual
Contents
1. 14 1 4 933mm 7 SUPPLIES 362mm C L OF DRAIN at 178mm ry ry i ra ele 5 LA 2 N fe 3 4 2 ay N I D7 ga 89mm 43 3 4 1111mm UTLINE OF ol SKID RESISTANT aie 4 26 3 4 4 679mm ala 40 3 8 1026mm SUPPORT LEGS L l CAST METAL DESIGN INSERTS 4 1 2 114mm PANELED INSERTS ae 8 108mm E 203mm 4 C L OF 76mm BATH RIM Gimi T 356mm OVERFLOW Z i Lt i H J J 25 FINISHED FLOOR 7 635mm a Ne 1 3 8 O D 1 2 N P TS nes oes TAILPIECE a em 70 1778mm view AA SUPPORT LEGS INSTALLER PLEASE LEAVE THESE INSTRUCTIONS WITH HOMEOWNER AS THEY PROVIDE IMPORTANT CLEANING INFORMATION e Drill Drill bits for wood or tile Level Tape Measure Pipe Wrench Crescent Wrench Slip Joint Pliers Screw Driver Standard Woodworking Tools Personal Safety Equipment Caulking Gun Torque Wrench with 1 2 Socket 2 Square Drive Supplies e Putty e Painter s Tape GENERAL SPECIFICATIONS FOR 2742 BATHING POOL INSTALLED SIZE 73 3 4 x 43 3 4 x 25 In 1873 x 1111 x 635mm WEIGHT 114 Lbs 66 Kg WEIGHT w WATER 748 Lbs 340 Kg GAL TO OVERFLOW 76 Gal 288 L BATHING WELL AT SUMP 41 x 21 1 2 In 1041 x 546mm BATHING WELL AT RIM 62 x 31 3 8 In 1575 x 797mm WATER DEPTH TO OVER2. 4 20 socket head bolts and hex key wrench see photo 5 Repeat for the remaining brackets Note all brackets must have the opening pointing in the same direction Slide the frame into position The leveler should touch the inside of the bracket as shown in photo 6 Tighten the lock nut onto the bracket so that it is snug Place the tub into the frame making sure that it is centered in the frame adjustments to the levelers as necessary Trace the outline of the center support onto the floor firmly tighten the jam and lock nuts and raise the tub off of the frame Apply 1 4 beads of the neutral cure silicone supplied 1 apart to the floor within the outline Lower the tub down to the floor so that center support compresses the silicone and the deck edges make contact with the frame 2 screws int the underside of the frame and into the wood blocks attached to the bathtub see photo 7 Repeat on the opposite end Wipe the excess silicone from the floor using mineral spirits Using the pre drilled holes in the frame on the long side drive four 4 wood screws thru the underside of the frame and up into the wood blocks attached to the bathtub Repeat on the other side Take two 2 of the leg covers and position them on the legs as shown in photo 8 Note the V notch should overlap and be on the outside of the legs so that the holes cover the slots photo 9 Using the 33 drill bit supplied drill a
3. 4 i RECOMMENDED TOOLS AND MATERIALS Hacksaw Tubing Cutter Drill misc bits Pipe Teflon Tape pipe sealant or Phillips Screwdriver 1 Hole Saw or Spade Bit Wrench Teflon Based Pipe Sealant Slotted Head Screwdriver Open end Adjustable Level Clear Silicone Sealant Tape Measure Wrench Torpedo Plumb Bob DO NOT USE PIPE DOPE FOR THREADED CONNECTIONS AS FINISH DETERIORATION MAY RESULT INSTALLATION MUST COMPLY WITH APPLICABLE LOCAL PLUMBING BUILDING CODES FLANGE NUT 5 DECK MOUNT GASKET SUPPLY WASHER FLANGE ADAPTER RISER FLOOR SCREWS UNION ESCUTCHEON NIPPLE l mt O i DECK MOUNT COVER HANDLE WASHER Assembly INSTALLATION PROCEDURES Step 1 Locate and mark correct centerline dimension for Bath Filler on bath deck per roughing in dimensions on installation instructions supplied with bath Plan Ahead be sure that floor joists do not interfere with water supply lines or drain connections Step 2 Extend hole centerlines from bath to floor using Plumb Bob Step 3 Drill 1 diameter holes for supply risers at locations marked in step 2 NOTE Water supplies are primarily factory assembled and water tested DO NOT attempt to disassemble supplies as surface may be damaged and warranty will be void Step 4 Assemble floor escutcheons and base flange to short pipe on supply risers Insert supply risers into floor mounting holes with shutoff valves facing outward and loosely install flat washers and locknuts on pipe nippl
4. Americam Standard Enfield Bathtub 2742 020 2742 222 Installation Instructions DuraBond Construction HIGH GLOSS ACRYLIC FITTINGS NOT INCLUDED THANK YOU for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please read these instructions carefully before you begin All you need to finish the installation are your selected fittings Certain installations may require professional help Also be sure your installation conforms to local codes GENERAL INSTALLATION INFORMATION Carefully uncrate and inspect your new bath and tub frame for any List of Required Components not included e 1593 170 295 Drain shipping damage If such damage is found report it to your vendor e 9116 017 295 Bath Filler immediately e 9117 012 295 Water Supplies w deck risers Protect all finished surfaces of the bath frame during construction Available at your American Standard Distributor and installation using a drop cloth If packaging foam is removed for inspection purposes save for frame installation procedure List of Required Tools and Supplies Fittings bath filler drain and water supplies are not provided with Tools the bath and must be ordered separately SUGGESTED LOCATION FOR BATH FILLER MOUNTING HOLES A 2 BY OTHERS 73 3 4 Mies 146mm 36 3 4 1873mm TE i 933 C L OF 1 2 NPTS a
5. FLOW 15 3 4 In 400mm FLOOR LOADING 36 Lbs Sq Ft 174 Kgs Sq m PROJECTED AREA PTS 27 8 CUBE FT 55 7 FOR AFTER SALES SERVICE CALL 1 800 442 1902 WEEKDAYS American Standard Inc 2004 All product names listed herein are trademarks of American Standard Inc unless otherwise noted 752846 100 Rev C 1 1 Identify desired location of the tub Please note the floor area supporting the tub and frame must be capable of supporting a load in excess of 2000 Ibs The supplies and drain must not interfere with the floor joists see rough in for dimensions 2 Place the wood frame finished side down on a soft surface to prevent scratching an old blanket or quilt may be suitable 3 Remove the unfinished shipping supports from each corner by remov ing the four 4 wood screws in each corner Save the screws for attaching the legs 4 Take a leg and insert it into the underside of the frame Be sure to have the studs protrude thru the opening in the corner of the frame see photo 1 5 Using the wood screws from step 3 attach the leg to the frame 6 Slide the corner bracket over the studs and using the nuts and wash ers provided secure the bracket to the frame see photo 2 Alternating between the nuts tighten to 10 ft lbs Do not overtighten 7 Repeat steps 4 thru 6 for the remaining legs 8 Assemble the jam nuts and lock nuts on the leveler bol
6. ade through the contractor or dealer from or through whom the product was purchased or that a service request including a description of the product model and of the defect be sent to the following address In the United States In Canada In Mexico American Standard Inc American Standard Ideal Standard S A de C V P O Box 6820 2480 Stanfield Road Planta Santa Clara Piscataway New Jersey 08855 Mississauga Ontario Via Morelos 330 Attention Director of Consumer Affairs Canada L4Y 1S2 Santa Clara Coatitla Ecatepec de Morelos 55540 For residents of the United States Toronto Area 905 306 1093 Estado de Mexico Mexico warranty information may also be Toll Free 800 387 0369 obtained by calling the following toll free number 800 442 1902 752846 100 Rev C 6 INSTRUCTIONS BATH FILLER SUPPLIES MODEL 9117 012 To ensure this product is installed properly please read these instructions carefully before you begin DESCRIPTION Bath Filler Supplies Model 9117 012 includes 6 deck mount supply adapters riser tubes couplings shutoff valves and all fittings and supports needed to install and connect the 9116 E Series Bath Filler to the water supplies pr s at Adjust centerline spacing of supports and water supply lines 7 as needed to accommodate American Standard 9116 Series Bath Filler Please refer to Bath Filler Installation Instructions for this dimension Amrican Standard INSTALLATION
7. ection of this American Standard plumbing product within one year after its initial purchase confirms that it is defective in materials or workmanship American Standard will repair or at its option exchange the product for a similar model Variations in actual wood color and finishes which may result from natural characteristics of the wood such as grain patterns mineral streaks and the like are not defects and are not covered by this warranty This warranty applies only to the original purchaser and installation of these products This limited warranty does not apply to local building code compliance Since local building codes vary considerably the purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before installation This warranty shall be void if the product has been moved from its initial place of installation if it has been subjected to faulty maintenance abuse misuse accident or other damages if it was not installed in accordance with American Standard s instructions or if it has been modified in a manner inconsistent with the product as shipped by American Standard American Standard s option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation nor shall American Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange
8. ed in connection with product removal or installation under this limited warranty 5 ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTIAL DAMAGES ALL OF WHICH ARE HEREBY EXPRESSLY DISCLAIMED OR THE EXTENSION BEYOND THE ONE YEAR DURATION OF THIS LIMITED WARRANTY OF ANY IMPLIED WARRANTIES INLCUDING THOSE OF MER CHANTABILITY OR FITNESS FOR PURPOSE INTENDED Some jurisdictions do not allow limita tions on how long an implied warranty lasts or the exclusion or limitation of incidental or consequen tial damages so these limitations and exclusions may not apply to you 6 Responsibility for compliance with local code requirements Since local code requirements vary greatly distributors dealers installation contractors and users of plumbing products should determine whether there are any code restrictions on the installation or use of a specific product 7 If a unit is purchased by a dealer and used as a demonstration unit the Warranty takes effect as soon as the dealer uses the product as a demo If this demonstration unit is subsequently sold to a customer the dealer may transfer the remaining period of the Warranty to the buyer only with American Standard written approval This warranty gives you specific legal rights You may have other statutory rights that vary from state to state or from province to province in which case this warranty does not affect such statutory rights For service under these warranties it is suggested that a claim be m
9. es from beneath floor Product names listed herein are trademarks of American Standard Inc 752870 100 Rev A American Standard Inc 2004 Step 5 Disassemble union assembly with 4 long threaded nipple Assemble brass flange nuts and flat rubber gasket onto threads of 4 long union nipple Protect surface finish of union coupling or cover wrench jaws to prevent marring of finish on coupling and assemble coupling to the top of the supply riser BE SURE TO USE TEFLON TAPE OR TEFLON PIPE SEALANT AT THIS CONNECTION Step 6 APPLY TEFLON TAPE OR TEFLON PIPE SEALANT to threads on union nipple 4 long threaded union nipple Insert 4 long threaded nipple up through hole in bath deck and assemble to union nut on top of supply riser DO NOT OVERTIGHTEN Tighten flange nuts and rubber gaskets to underside of bath Clear silicone sealant may also be used to provided a watertight seal between the bath and the water supply connection Step 7 Adjust the base flange as necessary to acquire proper height for assembled supply riser Shutoff valve stems should be aligned so that they are accessible 1 of threads maximum should be protruding through the bath deck to accommodate the 6 deck mounted supply adapters Drill 1 8 pilot holes through floor flange anchor holes and secure each flange to floor with four 10 x 2 screws Fully tighten under floor nipple locknuts Step 8 Assemble the 6 deck mounted supply adapters to 4 union
10. leaks around all drain connections POST INSTALLATION CLEAN UP Remove all construction debris from bath Do not use wire brushes or any other metal implement on bath surface Post installation clean up generally can be completed using warm water and liquid dishwashing detergent Stubborn dirt or stains may be removed using granular Spic and Span mixed with water Painter s naphtha can be used to remove excess adhesives and or wet oil base paint HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES Abrasive cleaners must not be used since they will scratch and dull the surface Dulled areas can be restored by rubbing with a white automotive type polishing compound and waxing with a liquid wax Do not allow compound to contact the wood frame If a scratch should occur in the backing material it is easily repaired by using paste or liquid shoe polish followed by buffing CARE AND CLEANING OF THE BATHTUB SUPPORT FRAME Please note that some chemicals may damage the finish on the frame Take care to avoid having the frame come into contact with the following iodine hair dye after shave lotion Lestoil Lysol Tub and Tile Cleaner Lysol Spray Disinfectant Dow Disinfectant acetone paint remover Formula 409 Tile X and Nair Use the Milsek Furniture Polish and Cleaner sample included to care for the support frame and panels 752846 100 Rev C 4 AMERICAN STANDARD ENFIELD BATHTUB FURNITURE WARRANTY If insp
11. nipple aligning coupling nuts toward bath sump Assemble bath filler per manufactures instructions Step 9 Remove shutoff valve handle lockscrews and assemble handle to stem Replace handle lockscrews and handle lockscrew cover on handle Step 10 Connect hot and cold water supplies to 1 2 inlets Step 11 When bath and drain installation is complete open shutoff valves and bath filler Flush lines check for leakage Close bath filler valves Repair leaks as required CARE AND CLEANING Please use the following care and cleaning procedures to ensure maximum enjoyment and use of your brass fixtures After every use wipe fittings gently with a soft damp cloth and dry thoroughly with a soft towel It is important to dry base areas where he fixtures come in contact with wet surfaces Fixtures should be cleaned with mild soapy water rinsed thoroughly with clear water and dried with a soft cloth Avoid detergents disinfectants or cleaning products in aerosol cans NEVER use acids abrasive scouring powders detergents or chemicals on brass fixtures FOR AFTER SALE SERVICE In the United States In Canada In Mexico American Standard Inc American Standard Customer Service Manager P O Box 6820 2480 Stanfield Rd Ideal Standard S A de C V Piscataway New Jersey 08855 Mississauga Ontario Via Morelos 330 Attention Director of Consumer Affairs Canada L4Y 1S2 Col Santa Clara For residents of the United States warranty T
12. of a defective product all of which are expressly excluded from this warranty Some states or provinces do not allow the exclusion or limitation of implied warranties so this exclusion may not apply to you This warranty gives you specific legal rights You may have other statutory rights that vary from state to state or province to province in which case this warranty does not affect such statutory rights See next page for more warranty information 752846 100 Rev C 5 AMERICAN STANDARD LIMITED WARRANTY ACRYLIC PRODUCTS American Standard warrants to the original consumer purchaser that it will at its option repair or replace any of its plumbing products found by it to be defective under normal use and maintenance within the following periods from date of purchase Shell three 3 years This limited warranty DOES NOT COVER the following 1 Defects or damage arising from shipping installation alterations accidents abuse misuse lack of proper maintenance and use of other than genuine American Standard replacement parts in all cases whether caused by a plumbing contractor service company the owner or any other person 2 Deterioration through normal wear and tear 3 Expense of normal maintenance periodic replacement of washers seals etc is a normal main tenance requirement 4 Postage or shipping costs for returning products for repairs or replacement under this limited war ranty and labor or other costs incurr
13. oll Free 800 387 0369 Ecatepec 55540 Edo Mexico information may also be obtained by calling the following toll free number 800 442 1902 www AmericanStandard US com h www AmericanStandard com mx www AmericanStandard ca PA 752870 100 Rev A
14. pilot hole 1 2 deep into the outside of the leg at the top hole Attach the cover to the leg where the pilot hole was drilled using the 6 x 3 8 pan head screws provided 752846 100 Rev C 3 34 Attach a screw in the bottom hole threading the screw into the slot 35 Repeat steps 32 thru 34 on the inside of the leg 36 Repeat for remaining legs 37 Install the faucet and drain per manufacture s instructions 38 Place the wood inserts or cast grilles into the opening in the center of the 6 side of the frame 39 Secure the panels to the frame with the deadbolt locks see photo 10 40 Apply painters tape to the frame 1 8 from the deck edge around the perimeter of the tub 4 Apply silicone sealant to the edge of the tub where it contacts the wood frame and using water to dampen your finger remove excess sealant to form a smooth line Apply additional sealant as necessary to provide a uniform bead from the deck edge to the masking tape 42 Carefully remove tape Dampen finger and run it lightly over the sealant to remove any high spots Use mineral spirits to remove excess silicone from the tub and frame DRAIN CONNECTION ASSEMBLY AND LEAK TEST Follow instructions provided with drain for proper assembly procedure Provide a 1 3 4 dia hole through floor in location specified in Fig 1 connect bath drain to waste line Tighten all drain joints securely Clean the bath and fill with water and check for
15. t and screw it into the threaded insert located on the bottom of the leg see photo 3 Note the bottom of the leveler bolt should be 1 from the bottom of the leg 9 Repeat for the other legs 10 Turn the frame over and place it in position on the floor Adjust the levelers so that frame is level Please note that the maximum adjustment is 1 8 up or down Shimming the legs is prohibit ed Additional adjustment must be accommodated in the floor as required 11 Slide the anti tip bracket over the leveler as shown in photo 4 12 Trace the outline of the bracket onto the floor 13 Repeat for the remaining legs 14 Move the frame about 1 ft in the direction of the opening on the anti tip bracket Note all brackets must have the opening pointing in the same direction 15 Place the anti tip bracket on the floor within the outline drawn in step 16 and trace the two holes onto the floor Note all brackets must have the opening pointing in the same direc tion 16 Drill the holes in the floor using a 3 8 drill bit and install the inserts using the supplied hex key wrench 752846 100 Rev C 2 17 18 19 20 2 _ 22 23 24 25 26 27 28 29 30 3 32 33 Check to see if the center support is within 1 16 of the floor Make Using a non marring clamp tighten the covers against the leg see Attach the anti tip bracket to the floor using the 1
Download Pdf Manuals
Related Search