American Standard Ceramix 2021.831 User's Manual
Contents
1. A ADJUSTMENT WHEN SETTING NUMBERS Ii WATER IS TOO HOT B ADJUSTMENT WHEN E f hand spray water WATER IS TOO COLD flow is restricted lift DIVERTER 10 using long nose pliers Clean and replace RED RING HOT LIMIT SAFETY STOP PRY RED RING UPWARD AND ROTATE CLOCKWISE 9 CARE INSTRUCTIONS DO SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER DRY WITH A SOFT COTTON FLANNEL CLOTH DO NOT DO NOT CLEAN THE PRODUCT WITH SOAPS ACID POLISH ABRASIVES HARSH CLEANERS OR A CLOTH WITH A COARSE SURFACE M66241 REV 1 22. irmly spread TUBES 6 for better access to LOCKNUT 3 27 32 DIA Bend TUBES 6 to meet supplies Use palm of hand to support TUBES 6 while bending to avoid kinking 1 1 8 DIA awe 127 Attach VALVE NIPPLE 1 with SEAL oe WASHER 2 to threaded STUD 5 J 3 8 OD COPPER gt BENDABLE T SPOUT BASE INSTALLATION SINK OR Remove ESCUTCHEON 1 with RUBBER MOUNTING RING 2 and insert SPOUT BASE 3 through SURFACE hole from underside of Sink Threads of SPOUT BASE 3 should extend at least 5 16 inch above mounting surface If necessary adjust LOCKNUT 4 Place RUBBER RING 2 into ESCUTCHEON 1 recess and thread ESCUTCHEON 1 onto SPOUT BASE 8 until snug against internal stop Turn SPOUT BASE 3 so that the side INLET NIPPLE 5 is directed towards valve Center SPOUT BASE 3 and tighten LOCKNUT 4 Place SEAL WASHERS 6 into coupling nuts of FLEXIBLE HOSE 8 and connect to side INLET NIPPLE 5 and VALVE NIPPLE 7 Check that both O RINGS 1 are properly seated on the valve center Check that the DIVERTER PLUG 2 is fr
3. Installation ey Instructions CERAMIX kaeraan KITCHEN FAUCETS HI FLOW SPOUT Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Certified to comply with ASME A112 18 1M M66241 REV 1 1 TOOLS REQUIRED ITA Channel Locks Adjustable Wrench Phillips Screwdriver 1 FAUCET INSTALLATION CAUTION Turn off hot and cold water supplies before beginning Remove VALVE NIPPLE 1 SEAL WASHER 2 LOCKNUT 3 This faucet permits an interchangeable mounting of d STUD tS cf velva rom each integral all ele spout valve and hand spray to suit the particular installation requirements Before starting installation ee each component loosely into the holes of the kitchen sink to select the most desirable arrangement ROUGHING IN DIMENSIONS Insert supply TUBES 6 and threaded STUD 5 through hole in sink Make sure black RUBBER RING 7 is properly seated in recess of base Orient valve so that threaded STUD 5 is centrally located towards the rear of sink then assemble MOUNTING ASSEMBLY 4 and thread LOCKNUT 3 onto STUD 5 from underside of sink i Hand tighten LOCKNUT 3 and check Sais aya MINA that rotation of HANDLE 8 from HOT MTG HOLE to COLD is centered Secure valve osition by tightening LOCKNUT 3 T SURFACE
4. ee and can move up and down D Push the SPOUT SUB ASSEMBLY 3 on to the SPOUT BASE 4 ni and tighten the SPOUT NUT 5 until snug on SPOUT BASE 4 i Place SPRAY HOLDER 6 into the appropriate mounting hole assemble WING NUT 7 onto shank of SPRAY HOLDER 6 from underside of sink and secure by tighting WING NUT 7 Feed SPRAY HOSE 8 through SPRAY HOLDER 6 and attach COUPLING NUT 9 of SPRAY HOSE 8 to HOSE ADAPTER 10 Tighten COUPLING NUT firmly 9 Make certain that SPACER WASHER 11 and RUBBER WASHER 12 are attached to SPRAY HOSE 8 and thread SPRAY HEAD 13 to NUT 14 Tighten NUT 14 firmly 5 SUPPLY CONNECTIONS E Bend 3 8 SUPPLY TUBES to meet water supplies valves Use palm of hand to support TUBES while bending to avoid kinking m Connect inlet TUBES to water supplies with appropriate connectors Connect left TUBE to HOT water supply and the right TUBE to the COLD water supply Note If additional supply length is required installer must purchase additional parts separately COMPRESSION NUT 3 8 O D SUPPLIES FERRULE M66241 REV 1 2 TEST INSTALLED FITTING With HANDLE 1 in OFF position turn on WATER SUPPLIES 2 and check all connections for leaks Remove AERATOR 3 Operate HANDLE 1 up and down in COLD and HOT positions to flush water lines thoroughly Direct SPRAY HEAD 4 into sink Open faucet and activate spray Check SPRAY HOSE 5 connections for leaks Re
5. place AERATOR 8 ADJUST HOT LIMIT STOP Clogged CARTRIDGE 1 inlets or outlets may cause reduced By restricting handle rotation and limiting the amount of flow in full on hot or cold To clean ports first turn off Hot hot water allowed to mix with the cold the HOT LIMIT and Cold water supplies then SAFETY STOP reduces risk of accidental scalding To set Remove BUTTON 2 loosen HANDLE SCREW 3 and pull the maximum hot water temperature of your faucet HANDLE 4 off i i i Remove ESCUTCHEON CAP 5 ae aa is adjust the setting on the HOT LIMIT Remove three MOUNTING SCREWS 6 Lift CARTRIDGE 1 off MANIFOLD 7 remove SEALS 8 f Clean ports SEALS 8 Use a flat blade screwdriver or your fingers to pull up and Insert SEALS 8 back into CARTRIDGE 1 Place CARTRIDGE rotate red HOT LIMIT SAFETY STOP 1 Follow Step A or 1 onto MANIFOLD 7 and alternately tighten the three B to adjust min max discharge temperature 0 being MOUNTING SCREWS 6 f the hottest to 7 the coldest temperature setting Factory Replace ESCUTCHEON CAP 5 HANDLE 4 and tighten set at 0 HANDLE SCREW 3 Replace PLUG BUTTON 2 AERATOR 9 may accumulate dirt causing distorted and reduced water flow Remove clean and replace AERATOR 9 a If faucet drips operate HANDLE 4 several times from PRY RED RING UPWARD a ta non i h AND ROTATE COUNTER off to on Do not apply excessive force CLOCKWISE ONE CLICK GAE A
Download Pdf Manuals
Related Search