American Standard 2775E User's Manual
Contents
1. GENERAL INSTALLATION INFORMATION Carefully uncrate and inspect your new bath for any shipping damage If such damage is found report it to your vendor immediately THANK YOU for selecting an American Standard bath Your new bath is shipped to you after careful inspection The whirlpool version is completely assembled with pump motor and system piping All you need to finish the installation are your selected fittings and electrical connections for a whirlpool To insure maximum performance and pleasure from this product please follow the instructions and cautions List of Optional Components not included e Flex Jet Pulse Jet Kit e Flex Jet Soft Jet Kit e E Z Install Heater e Tile Bead Kit List of Required Components not included Drain see your Home Depot Retailer e Bath Filler List of Required Tools and Supplies Tools Level Tape Measure Pipe Wrench Slip Joint Pliers Screw Driver Standard Woodworking Tools Personal Safety Equipment Caulking Gun Supplies Nails Putty Caulking waterproof 1x3o0r2xe Stringers Drop Cloth 20 amp GFI Outlet Cement Plaster Grout After inspection and during installation protect the bath from construction damage After installation and before enclosing with wallboard tile etc water test the unit and check for leaks Do not make modifications to the whirlpool system or remove pump from factory mounting This coul2. All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other applicable codes WARNING When using electrical products basic precautions should always be observed including the following 1 DANGER RISK OF ELECTRIC SHOCK Connect only to a circuit protected by a ground fault circuit interrupter 2 Grounding is required The unit should be installed by a licensed electrician and grounded 3 Install to permit access for servicing 4 All building materials and wiring should be routed away from the pump body and heater if equipped The whirlpool should be installed on a 120 vac 20 amp dedicated circuit The circuit should be hard wired from the electrical power supply panel The circuit must be a three 3 wire circuit from the electrical supply panel A grounded neutral wire and a third wire earth ground are essential HEATER EQUIPPED MODELS REQUIRE A SEPARATE 15 AMP MAXIMUM GFCI CIRCUIT ELECTRICAL INSTALLATION SEPARATE 20 AMP GFCI OUTLET WHIRLPOOL MOUNTED 120 VAC AIR SWITCH OR WALL TIMER ELECTRICAL DIAGRAM READ AND FOLLOW ALL INSTRUCTIONS 752874 100 Rev C 3 WIRE SELECTION GUIDE Maximum distance from fusebox to motor The sizes shown on this chart are recommendations Motor for copper conductors Hi Performance only Always follow Rating 120V Power Line local and national electrical codes DRAIN CONNECTION AND SYSTEM TEST Using recommended drain
3. opening connect whirlpool drain to waste line Tighten all drain joints securely Check the pump couplings and make sure they are hand tight Clean the whirlpool and fill with water to a point 2 above the top of the highest jet Recheck the pump couplings and make certain that they are not leaking Although the pump couplings are factory tightened and inspected some loosening may have occured during transit Make sure the whirlpool is connected to the electrical supply and turn the whirlpool on Check for leaks around all piping connections while the whirlpool is running POST INSTALLATION CLEAN UP Remove all construction debris from bath Tile grout can be removed with a wooden popsicle stick or tongue depressor Do not use wire brushes or any other metal implement on bath surface Post installation clean up generally can be completed using warm water and liquid dishwashing detergent Stubborn dirt or stains may be removed using granular Spic and Span mixed with water Painter s naphtha can be used to remove excess adhesives and or wet oil base paint HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES Abrasive cleaners must not be used since they will scratch and dull the surface Dulled areas can be restored by rubbing with a white automotive type polishing compound and waxing with a liquid wax 752874 100 Rev C 4 SPIC AND SPAN Is A REGISTERED TRADEMARK OF PROCTER amp GAMBLE
4. CADET ELITE CORNER HIGH GLOSS ACRYLIC SHOWN LESS ALL FITTINGS 2775E SERIES WHIRLPOOL Amirieam Standard INSTALLATION INSTRUCTIONS 42 1 2 t 229 X 305mm 1080mm 9X12 CUTOUT IN FLOOR FOR DRAIN 1076mm IN LINE HEATER 42 3 8 REMOVABLE 1524mm BLANK d RECOMMENDED FITTING LOCATION 64 X 330mm 2 1 2 X 13 ON OFF swen A 60 PROVIDE ACCESS TO PUMP FOR SERVICING ON ALL INSTALLATIONS y OUTLINE OF j CUTOUT cL 1080 mm u2 7i C L OF DRAIN OUTLET 2159mm 85 76mm m LEVELING STRINGER Ci OF NOT FOR SUPPORT 38 mm REF OVERFLOW 3 F 1 1 2 NV 7 j as K j 502mm INTEGRAL SUPPORT FEET 112NP TM THREADS 1 1 2 O D TAILPIECE 2 3 4 19 3 4 464mm 18 1 4 INSTALLED SIZE WEIGHT WEIGHT w WATER GENERAL SPECIFICATIONS FOR 2775E WHIRLPOOL 85 X 60 X 19 3 4In 2159mm X 1524 mm X 502mm 130 Lbs 59 Kg 756 Lbs 343 Kg GAL TO OVERFLOW 75 Gal 284 L MIN OPERATING GAL 60 Gal 227 L BATHING WELL AT SUMP____ 32 X 32 In 813 mm X 813 mm BATHING WELL AT RIM WATER DEPTH TO OVERFLOW FLOOR LOADING 46 X 46 In 1168 X 1168mm 14 In 356 mm 34 Lbs Sq Ft 115 Kgs Sq m PROJECTED AREA PTS 41 7 CUBE FT 70 4 PUMP WHIRLPOOL ELECTRICAL SPECIFICATIONS 2 1 HP 14 4 AMPS 120V
5. d adversely affect the safety and performance of the whirlpool and void the warranty Do not handle or move the whirlpool by the pump motor or piping system Fittings bath filler shower arm etc are not provided with the bath and must be ordered separately Framing and enclosing materials are provided by others Check for availability of optional American Standard wall tiling bead required for recess installations Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth WARNING Do not lift whirlpool by the piping harness at any time FOR AFTER SALES SERVICE CALL 1 800 223 0068 WEEKDAYS 752874 100 Rev C American Standard Inc 2003 All product names listed herein are trademarks of American Standard Inc unless otherwise noted INSTALLATION AND FRAMING INSTRUCTIONS The variety of installations possible for this whirlpool may require framing procedures other than those shown Locate studs as required Ensure roughing in dimensions are proper plumb and square Provisions must be made in all installations for an access opening for servicing the pump and controls It is strongly recommended that an additional opening be provided for access to the drain components NOTE The apron should not be used as the primary access opening 1 Position the whirlpool into the installation opening and level the deck shimming the integral support feet as necessary Mark the final position of
6. the underside of the deck by tracing a line on to the studs see Figure 1 2 Remove the whirlpool and attach a 2 x 4 stringer to the studs with the top of the stringer touching the traced line 3 Install drain components to the whirlpool following the manufacturers instructions Before replacing your whirlpool for final installation be certain that an opening has been provided in the sub floor for the drain See the roughing in drawing for suggested opening size and location dimensions 4 Replace whirlpool and re shim the integral support feet shimming the entire length of the support feet Secure the shims using construction adhesive silicone mortar or equivalent materials While not a necessity the use of a foundation base consisting of cement e g Sakrete mortar or grout will help provide a solid and secure installation FIG 1 TYPICAL CORNER INSTALLATION 58 1 2 ah 58 1 2 1486mm 1486mm SUGGESTED INSTALLATION METHODS LEVELING SURFACE TILE WATERPROOF WATERPROOF SEALANT SEALANT LEVELING STRINGER BATH BATH V N HEIGHT OF FRAMEWORK INCLUDES PLYWOOD TILES ETC SUNKEN OR ISLAND RECESSED INSTALLATION INSTALLATION FRONT OR SIDE ACCESS PANEL REQUIRED FOR SEE CUTOUT TEMPLATE PROVIDED PUMRSERYICING UNLESS AN ACCESS OPENING OF AT LEAST 12 X 24 305 X 610MM IS PROVIDED WARRANTY SERVICE WILL NOT BE PERFORMED 752874 100 Rev C 2 ELECTRICAL INSTALLATION INSTRUCTIONS
Download Pdf Manuals
Related Search