American Standard Ardsley 4962.150 User's Manual
Contents
1. SUPPLIES 1 2 directly to wall supplies Connection on fitting supplies are 3 8 compression Connect left supply to Hot and right supply to the Cold wall supply Use adjustable wrench to tighten connections Do not over tighten Faucet supplies are 10 long from faucet base Note If additional supply length is required installer must purchase additional parts separately Important If SUPPLY HOSES 1 2 are too long loop as illustrated to avoid kinking Figure A LOOP SUPPLIES IF REQUIRED Aap a bead of PUTTY to underside of DRAIN BODY FLANGE 1 Feed DRAIN BODY 1 down through lavatory Assembly GASKET 2 WASHER 3 and LOCKNUT 4 onto DRAIN BODY 1 Tighten LOCKNUT 4 firmly Assembly TAILPIECE 5 to DRAIN BODY 1 M968847 TEST INSTALLED FAUCET AND CHECK FOR LEAKS With HANDLE 1 in OFF position turn on WATER SUPPLIES 2 and check all connections for leaks Remove AERATOR 3 Operate HANDLE 1 to flush water lines thoroughly Replace AERATOR 3 5 HOT LIMIT SAFETY STOP ADJUSTMENT E By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold the HOT LIMIT SAFETY STOP reduces risk of accidental scalding To set the maximum hot water temperature of your faucets all you need to do is adjust the setting on the HOT LIMIT SAFETY STOP Loosen SET SCREW 2 with 2 5mm hex wrench Pull HANDLE 1 off valve stem Pull off CAP 32. Use a flat blade screwdriver or your fingers to pull up and rotate red HOT LIMIT SAFETY STOP 4 Follow Step A or B to adjust min max discharge temperature O being the hottest to 7 the coldest temperature setting Factory set at O Replace ESCUTCHEON CAP 3 HANDLE 11 tighten HANDLE SCREW 2 B PRY RED RING FORWARD AND ROTATE CLOCKWISE B ADJUSTMENT WHEN WATER IS TOO COLD CARE INSTRUCTIONS To keep your new faucet looking new please follow these simple care instructions DO g Simply rinse the faucet clean with clear water m Dry the faucet with a soft cotton cloth DO NOT Do not use any abrasive cleaners cloths or paper towels Do not use ay cleaning agents containing E acids polish abrasives or harsh cleaners or soaps Regular and routine cleaning will reduce the need for heavy cleaning and polishing If heavy cleaning is required the following procedures are recommended PRY RED RING FORWARD AND ROTATE COUNTER CLOCKWISE ONE CLICK lt lt A a ADJUSTMENT WHEN WATER IS TOO HOT TEMPERATURE SETTING NUMBERS RED RING HOT LIMIT SAFETY STOP m Remove as much surface dirt and film using clear water and soft cotton cloth as described above Use any of the following to remove tough surface film and build up Mild liquid detergents Clear ammonia free liquid glass cleaners Non acidic non abrasive gentle We or fully dissolved powder cleansers mixed according to manufactu
3. Installation Instructions ARDSLEY 4962 150 TRADITIONAL VESSEL FAUCET 4962 151 Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Certified to comply with ANSI A112 18 1 M968847 Recommended Tools amp Materials Adjustable Wrench Plumbers Putty or Channel Locks Caulking INSTALL FAUCET ALEI curries betore beginning For single hole only NOTE The FAUCET with EXTENSION is used for installation with above counter sinks With the collar of the EXTENSION 1 facing up slide the EXTENSION 1 over the FAUCET SUPPLIES 2 and the MOUNTING STUD 3 The collar of the EXTENSION 1 fits into the groove of the faucet T Y paucer Seat SEAL 4 into groove in EXTENSION 1 base GROOVE Feed FAUCET SUPPLIES 2 and MOUNTING STUD 3 through mounting hole of deck COLLAR From below push RETAINING WASHER and GASKET 5 onto MOUNTING STUD 3 Secure Faucet with MOUNTING NUT 6 pulling faucet to front of sink so STUD 3 rests against mounting hole Before final tightening adjust faucet so that it is centered Tighten MOUNTING NUT 6 to complete installation GROOVE ad EXTENSION BASE MOUNTING SURFACE 2 MAKE WATER SUPPLY CONNECTIONS E Turn off hot and cold water supplies before beginning m Connect FLEXIBLE
4. rers directions Non abrasive liquid polishers a Once clean rinse faucet again with clear water to gw thoroughly remove cleaner or polish and blot dry with a soft cotton cloth Failure to follow these care instructions may damage the Faucet s finish M968847
Download Pdf Manuals
Related Search