American Standard Arch Control Kitchen Faucet 4101.301 User's Manual
Contents
1. AL 14 into underside of ESCUTCHEON 12 From underside of sink or mounting surface thread LOCKNUT 13 onto SPRAY HOLDER 11 shank and tighten Install SPOUT ASSEMBLY Insert SEAL WASHER 1a into ESCUTCHEON 2a Insert SPOUT HOSE 10 and SHANK 11 through ESCUTCHEON 2a and mounting surface Make sure slot in spout base aligns with tab on ESCUTCHEON 2a Figure 2 Assemble RUBBER WASHER 5a BRASS WASHER 6a and threaded LOCKNUT 7a onto SHANK 11 from underside of sink or mounting surface Hand tighten LOCKNUT 7a Use a screwdriver to tighten SCREWS 9a on LOCKNUT 7a the same as fitting installation above Figure 1 Figure 2 ALIGN SLOT AND TAB ALIGN SLOT AND TAB 2 MAKE WATER SUPPLY CONNECTIONS Push HOSE END 1 with compression fitting onto COPPER TUBE 2 Make sure HOSE and COPPER TUBE are fully engaged approx 1 2 engagement Use adjustable wrench to tighten connections Do not over tighten Turn off hot and cold water supplies before beginning Connect FLEXIBLE SUPPLIES 3 directly to wall supplies Connection on fitting supplies are 3 8 compression Connect left supply Marked with a Red Stripe to Hot and right supply to Cold wall supply Use adjustable wrench to tighten connections Do not over tighten Faucet supplies are 24 1 2 long from faucet base Note If additional supply length is required installer must purchase those parts separately Important If SUPPLY HOSES 3 are too long loop as2. D 7 and remove CARTRIDGE SEALS 8 Clean MANIFOLD 7 CARTRIDGE 6 ports and SEALS 8 Place SEALS 8 into CARTRIDGE PORTS 6a Place CARTRIDGE 6 onto MANIFOLD 7 and tighten MOUNTING SCREWS 5 alternately Replace ESCUTCHEON CAP 4 HANDLE 3 tighten HANDLE SCREW 1 and install INDEX BUTTON 2 Test fitting CARE INSTRUCTIONS DO SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER DRY WITH A SOFT COTTON FLANNEL CLOTH DO NOT DO NOT CLEAN THE PRODUCT WITH SOAPS ACID POLISH ABRASIVES HARSH CLEANERS OR A CLOTH WITH A COARSE SURFACE M968583 ARCH Americam Standard HI FLOW KITCHEN FAUCET with SIDE SPRAY MODEL NUMBERS M962717 YYYOA fj B HANDLE KIT M962716 0070A _ BUTTON AND SCREW KIT M907305 YYYOA CARTRIDGE COVER M918521 0070A CARTRIDGE SCREWS A951470 0070A CARTRIDGE 042850 0070A DIVERTER M9627415 YYYOA j AERATOR Replace the YYY with appropriate finish code CHROME 002 STAINLESS STEEL 075 M953578 YYYOA HAND SPRAY AND HOSE 4101 301 M962725 YYYOA ESCUTCHEON KIT M923651 YYYOA 4101 301 SPRAY HOLDER M907610 YYYOA j z M962726 YYYOA SPRAY ESCUTCHEON ER ESCUTCHEON KIT 4101 301 WITH PUTTY PLATE z 4101 000P 060467 0070A MOUNTING KIT M923276 0070A SUPPLY HOSE M962722 0070A SPRAY HOSE AND SEAL HOT LINE FOR HELP For toll free inf
3. Installation Instructions ARCH 4101 301 HI FLOW KITCHEN FAUCET with SIDE SPRAY Thank you for selecting American Standard 4101 301 shown with 4101 301 the benchmark of fine quality for over 100 years aptipnal essuterean A101 600k To ensure that your installation proceeds smoothly Certified to comply with ANSI A112 18 1M please read these instructions carefully before you begin M968583 RECOMMENDED TOOLS Adjustable Wrench Regular Screwdriver Phillips Screwdriver Channel Locks INSTALL FAUCET WITH DECK ESCUTCHEON 410 351 ELE Installation with DECK ESCUTCHEON Apply a light bead of plumbers putty to underside of ESCUTCHEON 1 if mounting surface is uneven Place ESCUTCHEON 1 onto sink or mounting surface with large opening to the right as shown Insert supply HOSES 2 and SHANK 3 through ESCUTCHEON 1 and mounting surface Make sure slot in fitting base aligns with tab on ESCUTCHEON 1 Figure 1 Assemble RUBBER WASHER 4 BRASS WASHER 5 and threaded LOCKNUT 6 onto SHANK 3 from underside of sink or mounting surface Hand tighten LOCKNUT 6 and check that rotation of HANDLE 7 from HOT to COLD is centered Use a screwdriver to tighten SCREWS 8 on LOCKNUT 6 Work your way around LOCKNUT 6 tightening the SCREWS 8 slightly each time until all are snug to ensure even pressure Install SPRAY HOLDER Insert SPRAY HOLDER 11 into ESCUTCHEON 1 From un
4. derside of sink or mounting surface thread LOCKNUT 12 onto SPRAY HOLDER 11 shank and tighten Install SPOUT ASSEMBLY Insert SPRAY HOSE 9 and SHANK 10 through ESCUTCHEON 1 and mounting surface Make sure slot in spout base aligns with tab on ESCUTCHEON 1 Figure 2 Assemble RUBBER WASHER 4a BRASS WASHER 5a and threaded LOCKNUT 6a onto SHANK 10 from underside of sink or mounting surface Hand tighten LOCKNUT 6a Use a screwdriver to tighten SCREWS 8a on LOCKNUT 6a the same as fitting installation above Figure 2 ALIGN SLOT AND TAB ALIGN SLOT AND TAB INSTALL FAUCET WITHOUT ESCUTCHEON PLATE 4101 115 with soap dish 4101 350 less soap dish B Insert SEAL WASHER 1 into ESCUTCHEON 2 Place ESCUTCHEON 2 onto sink or mounting surface Insert supply TUBES 3 and SHANK 4 through ESCUTCHEON 2 and mounting surface Make sure slot in fitting base aligns with tab on ESCUTCHEON 2 Figure 1 Assemble RUBBER WASHER 5 BRASS WASHER 6 and threaded LOCKNUT 7 onto SHANK 4 from underside of sink or mounting surface Hand tighten LOCKNUT 7 and check that rotation of HANDLE 8 from HOT to COLD is centered Use a screwdriver to tighten SCREWS 9 on LOCKNUT 7 Work your way around LOCKNUT 7 tightening the SCREWS 9 slightly each time until all are snug to ensure even pressure Install SPRAY HOLDER Insert SPRAY HOLDER 11 into ESCUTCHEON 12 Insert SE
5. illustrated to avoid kinking M968583 CONNECT SPRAY HOSE AND SPOUT HOSE B Feed HAND SPRAY HOSE 1 through SPRAY HOLDER 2 Use wrench to tighten COUPLING NUT 3 on SPRAY HOSE 1 to SIDE SPRAY CONNECTION 4 on fitting m Make sure SEAL WASHER 5 is installed in COUPLING NUT 6 Connect threaded end of HOSE 7 to SPOUT HOSE COUPLING NUT 6 from fitting Use wrench to tighten 4 CHECK CONNECTIONS FOR LEAKS m Move HANDLE 1 down into off position W Turn on water supplies and check connections for leaks CHECK CONNECTIONS m FOR LEAKS M968583 5 TEST INSTALLED FAUCET Move HANDLE 1 down into off position Remove AERATOR 2 Operate handle up and down in COLD and HOT positions to flush water lines thoroughly m Replace AERATOR 2 m With HANDLE 1 down in off position pull HAND SPRAY 3 from holder and direct SPRAY END 3 into sink Check HAND SPRAY 3 operation m With faucet on push BUTTON 4 to activate HAND SPRAY 3 m Release BUTTON 4 to stop spray and return HAND SPRAY 3 to holder SERVICE If faucet drips operate HANDLE several times from off to on Do not apply excessive force Clogged CARTRIDGE outlets or inlets may cause reduced flow To clean first turn off water supply then m Remove INDEX BUTTON 1 loosen HANDLE SCREW 2 and remove HANDLE 3 Unthread ESCUTCHEON CAP 4 Unthread three MOUNTING SCREWS 5 Lift CARTRIDGE 6 off MANIFOL
6. ormation and answers to your questions call 1 800 442 1902 Weekdays 8 00 a m to 6 00 p m EST IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 Weekdays 8 00 a m to 7 00 p m EST IN MEXICO 01 800 839 12 00 Product names listed herein are trademarks of American Standard Inc AS America Inc 2008 M968583
Download Pdf Manuals
Related Search