American Standard Multi-tool 2891 User's Manual
Contents
1. damage and install wax ring evenly around TIP Place 2 pieces of masking waste flange horn with tapered end of ring a ie A E pel oa closet tape on floor as shown to facing toilet Apply a thin bead of sealant i help with alignment in step 5 around toilet base b Loosely install retainer washers and nuts INSTALL TOILET BOLT COVER Position toilet squarely to wall and with a rocking motion press bowl down fully on wax ring and flange Alternately tighten nuts until toilet is firmly seated on floor CAUTION DO NOT OVERTIGHTEN NUTS OR BASE MAY BE DAMAGED Back Side Peel both protective films off Install bolt covers and stick bolt cover to toilet 1 Make sure that the bolt cover area on the toilet is clean and dry see figure Use a dry piece of cloth or soap and water A if needed P Take plastic bolt cover and peel the brown protective film off lt gt on both ends The adhesive part is now visible and ready to be placed on the toilet see figure SE See Gently place the bolt cover on the toilet area see picture and if Front Side everything is aligned push bolt cover firmly so it remains in place BOLT COVER If not aligned you can still take it off and put it back so it is aligned Repeat Step 3 for second bolt cover which is to be placed on opposite side of the toilet After 24 hours the bolt cover adhesive has completely set off and if needed you can remove replace as need2. Dual Flush Valve Seal 7381203 200 0070A Push Button Kit Tank Cover Slow Close Contemporary EL Seat Bolt Cap Cover Kit Inlet Valve TROUBLESHOOTING GUIDE POSSIBLE CAUSE CORRECTIVE ACTION Does not flush a Water supply valve closed a Open valve and allow water to fill tank b Supply line blocked b Shut off water supply disconnect supply line and inspect all gaskets and washers Reassemble c Sand or debris lodged in water control c See Fluidmaster maintenance see Step 13 Poor or sluggish flush a Tank water too low a Check that the water level is set to the mark inside the tank b Bowl water too low b Check that the refill tube is connected to the water control and flush valve port Adjust refill float down until bowl water is restored see Step 9 c Water supply valve partly closed c Open water supply valve fully Be sure that proper water supply tube size is used d Partially clogged trapway and or drain pipe and or vent d Remove obstruction Consult a plumber if necessary e Water supply pressure too low e Minimum water supply pressure 20psi Wait for tank to refill Toilet leaks a Poor supply line connection a Review Step 8a and 8b pe O aeanoea Semmens O O Toilet does not shut off a Flush valve seal leaking or deformed a Clean debris from seal surface Replace flush valve seal as needed b Sand or debris lodged in water control b See Step 13 Fluidmaster maintenance c
3. Water level set too high c Set water level to mark on back of tank 7301690 100 Rev E
4. result in breakage and PLASTIC SUPPLY LINE potential flooding DO NOT OVERTIGHTEN 7301690 100 Rev E Rod Adjustment SEE STEP 11 IMPORTANT Refill Float Adjustment If short flush does not refill the bowl turn thumbscrew CCW 1 turn flush repeat if necessary Install and adjust push button rods for about Turn on water supply 1 16 1 1 2mm Submerge the FLOAT CUP clearance between rod under the water for 30 seconds end and valve button Adjust the water to desired level WATER LEVEL Vo SEE STEP 11 TIPS by turning WATER LEVEL ADJUSTMENT ADJUSTMENT ROD and moving FLOAT CUP up or down THREADED 5 SHANK Diagram 1 FLUSH PUSH BUTTONS e The large flush button should line up over the LARGE FLUSH BUTTON SMALL FLUSH BUTTON white actuator on the flush tower in the tank FOR SOLID WASTE FOR LIQUID WASTE 1 6 gal flush 1 1 gal flush e The small flush button should line up over the 6 Liter flush 4 1 Liter flush gray actuator on the flush tower in the tank e Pressing both buttons at once will result in a short flush TIPS With the lid removed directly press the flush button in the tank to confirm that the toilet is working properly If not follow troubleshooting guide 1 Install Threaded Rods into holes in bottom of push buttons approximately 1 2 12mm Lightly snug Locking Nut Place Lid on Tank Lockn ts Push Button to test flush If more stroke is needed loosen Locknut and tur
5. EVARD DUAL FLUSH ONE PIECE TOILET FINISHED WALL 29 3 4 7 1 2 756 mm 14 1 2 192 mm 368 mm lt ae C L OF SEAT POST HOLES 5 1 2 140mm CENTERS 18 1 2 470 mm SUPPLY AS 30 7 8 REQUIRED 784 mm position 1 or position 2 16 1 2 t 419 mm 5 1 2 140mm 8 1 2 13 1 2 x 6 ao 345 mm FINISHED 14 1 4 152mm 305 mm FLOOR 364 mm IMPORTANT Water supply on the wall is required at 3 3 4 or 9 from centerline of the toilet see rough in First suggested position is hidden behind the toilet The geometry of the toilet gives space for this installation The second suggested position is next to the toilet Between these two positions the space for the supply between wall and toilet is limited to 3 1 4 In this case check your supply and hose dimensions 73016 D 90 100E Product names listed herein are trademarks of AS America Inc AS America Inc 2012 7301690 100 Rev E SAVE FOR FUTURE USE INSTALL CLOSET BOLTS Install closet bolts in flange channel turn 90 and slide into place 6 152mm apart and parallel to wall NUT OPENING oR CLOSET SEALANT WAX RING BOLT INSTALL WAX SEAL Invert toilet on floor cushion to prevent POSITION TOILET ON FLANGE
6. INSTALLATION INSTRUCTIONS American Standard BOULEVARD Dual Flush One Piece Toilet ote THAT tke Barres Model 2891 Elongated Right Height with Seat Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure A S this product is installed properly please read these instructions carefully before you begin Certain oe we installations may require professional help Also be sure your installation conforms to local codes cored by IAPMO R amp T A CAUTION PRODUCT IS FRAGILE TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE NOTE Pictures may not exactly define contour of china and components RECOMMENDED TOOLS AND MATERIALS Regular Screwdriver Adjustable Wrench Putty Knife Sealant Carpenters Level Wax Ring Gasket Flexible Supply Tube Closet Bolts Hacksaw Tape Measure REMOVE OLD TOILET a Close toilet supply valve and flush tank completely Towel or sponge remaining water from tank and bowl b Disconnect and remove supply line NOTE f replacing valve first shut off main water supply c Remove old mounting hardware remove toilet and plug floor waste opening to prevent escaping sewer gases d Remove closet bolts from flange and clean away old wax putty etc from base area NOTE Mounting surface must be clean and level before new toilet is installed ROUGHING IN DIMENSIONS NOTE Distance from wall to closet flange centerline must be as listed below Model 2891 BOUL
7. ed The dual lock technology is now in place c Smooth off the bead of sealant around base Remove excess sealant NUT CLOSET BOLT 7 INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer s directions SEM Before continuing determine the type of water supply connection you have from the chart below and use the appropriate assembly parts required to properly reconnect the water supply DO NOT use plumber s putty to seal these fittings RECOMMENDED METAL COPPER METAL FLANGED METAL SPIRAL VINYL BRAIDED FLARED TUBING TUBING TUBING CONNECTOR LOCK NUT N LOCK NUT N LOCK NUT CONE XS EXISTING EXISTING COUPLING 7 WASHER WASHER CONE WASHER _ COUPLING _ EXISTING NUT COUPLING COUPLING NUT NUT WATER WATER WATER WATER SHUT OFF SHUT OFF SHUT OFF SHUT OFF These parts must be used as Use existing Use existing spiral cone Captive cone washers illustrated to insure water tight coupling nut washer Fluidmaster already included No connection Use of existing and washer cone washer may not additional washers needed coupling nut may result in seal completely on water leakage Water supply spiral type supply line tube or pipe must extend at least 1 2 inside threaded shank of valve does not apply to flanged tubing With correct washers in place see CAUTION Overtightening of Step 8a tighten COUPLING NUT CAUTION DO NOT USE LOCK NUT or COUPLING NUT 1 4 turn beyond hand tight CONE WASHER WITH could
8. he refill tube is inserted into overflow pipe below water level in tank Attach refill tube to overflow pipe using S clip provided e The flush valve is leaking because it s worn dirty or misaligned with tank ball or flapper replace with a new flapper IF FILL VALVE WON T TURN ON OR SHUT OFF or REFILL OF TANK WATER IS SLOW after valve has been in use for some time Fluidmaster Model 242 Replacement Seal may be needed Go to our website at www fluidmaster com for more solutions to toilet problems For troubleshooting information please contact POSITION VALVE MAY NOT TURN ON IF TOP IS NOT FULLY TURNED TO THE LOCKED POSITION a few times Leave water supply off lifting arm and rotating top and arm 1 8 turn counterclockwise pressing down slightly on cap Fluidmaster nc 30800 Rancho Viejo Road San Juan Capistrano CA 92675 949 728 2000 800 631 2011 www fluidmaster com 2001 Fluidmaster Inc Registered trademark of Fluidmaster Inc Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products Fluidmaster shall not be responsible or liable for any damages caused by products used with Fluidmaster valves that were not manufactured by Fluidmaster Inc REPAIR PARTS LIST NOTE XXX represents color options Specify when ordering PART NUMBER DESCRIPTION 735169 XXX0A 5218 110 XXX 7381073 XXX0A 738565 457 0070A 7381206 400 0070A Dual Flush Valve Assembly 7381213 200 0070A
9. n Threaded Rod counterclockwise one 1 turn Replace Lid Repeat until flush action is achieved Threaded Rods If Valve stays open turn Threaded Rod clockwise one 1 turn and lightly snug Locknut CARE AND CLEANING When cleaning your toilet wash it with mild soapy water rinse thoroughly with clear water and dry with a soft cloth Avoid detergents disinfectants or cleaning products in aerosol cans NEVER use abrasive scouring powders or abrasive pads on your toilet seat Some bathroom chemicals and cosmetics may damage the seat s finish A WARNING Do not use in tank cleaners Products containing chlorine calcium hypochlorite can seriously damage fittings in the tank This damage can cause leakage and property damage American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine calcium hypochlorite 3 7301690 100 Rev E IMPORTANT Always clear sand and rust from system e Make sure water supply is off Remove valve TOP by e While holding a container over the uncapped VALVE to prevent splashing turn water supply on and off e Replace TOP by engaging lugs and rotating 1 8 turn clockwise MAKE CERTAIN TIP IS TURNED TO THE LOCKED TROUBLESHOOTING IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK SLOWLY repeat Step 13 IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF NON USE it is a signal you are wasting water because e The end of t
Download Pdf Manuals
Related Search