American Standard 4" Centerset Lavatory and Bar Sink Faucets 5401 Series User's Manual
Contents
1. Attricam Staudard HERITAGE Aili HERITAGE SERIES 4 CENTERSET LAVATORY AND BAR SINK FAUCETS Installation Instructions 5400 SERIES 5401 SERIES 5402 SERIES 7400 SERIES 7401 SERIES 7402 SERIES 7490 SERIES Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please read these instructions carefully before you begin 5401 SERIES CENTERSET W POP UP 7401 SERIES CENTERSET WITH GOOSENECK SPOUT WASHER BRASS D WASHER LocKNUT COUPLING NUT 7490 SERIES BAR SINK WITH SWING SPOUT Certified to comply with ANSI A112 18 1M U S PATENT NOS 5 819 789 4 294 289 34063M B HANDLE ae SCREW THUMBSCREW EXTENSION TAILPIECE O DRAIN 3 FLANGE GASKET wee WASHER NUT CAUTION HANDLE SCREW Turn off hot and cold water supplies before beginning UPPER LIET ROD E Apply a bead of PUTTY along the edge of the underside of the BODY and insert faucet SHA K KS through holes of S HM Assemble RUBBER and BRASS WASHERS and LOCKNUTS from underside of SINK Drop UPPER LIFT ROD through hole in BODY models 5401 amp 7401 only align BODY as far forward as possible and secure position by tightening LOCKNUTS Plastic LOCKNUTS on model 7490 are tightened by hand Connect the HOT water supply to the left SHANK and the COLD water sup2. OD onto POP UP ROD and tighten THUMBSCREW Operate both handles to flush water lines thoroughly Check TEST INSTALLED FAUCET spout mounting and hose connections for leaks Remove AERATOR Operate LIFT ROD and check DRAIN for leaks With handle in OFF position turn on water supplies and check Turn handles into OFF position and replace AERATOR all connections for leaks SERVICE E if spout drips operate handles several times from OFF to ON position Do not force handles turn only 90 To change direction of handle rotation SPRING proceed as follows NULL m Turn valve to OFF position a Plastic SCREEN in CARTRIDGE may accumulate Sip HANDLE with ADAPTER aff f dirt causing reduced water flow To clean first Remove SPRING CLIP turn off hot and cold water supplies then Remove INSERT and HANDLE SCREW m Lift STOP WASHER turn 90 and replace m Replace SPRING CLIP Slip HANDLE with ADAPTER off CARTRIDGE m Replace ADAPTER HANDLE SCREW and INSERT Thoroughly rinse plastic SCHEEN at C AERATOR may accumulate dirt causing distorted and reduced base of CARTRIDGE water flow Remove AERATOR and rinse clean Replace CARTRIDGE until flange is tight against valve body Turn valves OFF SCREEN HOTLINE FOR HELP Replace ADAPTER HANDLE SCREW and INSERT For toll free information and answers to your questions call 1 800 223 0068 Product names listed herein are trademarks of American Standard Inc Weekday
3. ply to the right SHANK using sealant appropriate connectors and COUPLING NUTS Refer to separate Instruction Sheet for assembly of handles 1 2 0 D SLIP FLANGE DRAIN ASSEMBLY C RUBBER WASHER Models 5402 and 7402 only A aa WASHER ees Sn LOCKNUT Apply a bead of PUTTY around underside 8 o AIN PLUG flange Insert DRAIN PLUG into SINK drain hole COLD Hold DRAIN PLUG to prevent turning RUBBER A and assemble GASKET WASHER and GASKET LOCKNUT from underneath sink D NS WASHER Insert threaded end of TAILPIECE COUPLING Nur into lower end of DRAIN PLUG Connect other end to trap INSTALL POP UP DRAIN _ STOPPER Models 5401 and 7401 only FLANGE Remove one end of CLIP from PIVOT ROD by squeezing ends together while sliding Insert PIVOT ROD into second or third hole in Push TAILPIECE down into TRAP threaded end up N S EXTENSION and reassemble CLIP EXTENSION x Thread LOCKNUT WASHER and GASKET onto may need to be bent DRAIN BODY PUTTY 3 ee Adjust STOPPER height by eer ane EXTENSION Apply a bead of PUTTY to underside of FLANGE and tightening THUMBSCREW Feed DRAIN BODY up through SINK and thread SINK FLANGE fully onto BODY m GASKET Tighten LOCKNUT firmly keeping the PIVOT ROD Sth POP UP ROD pointed towards the back of the SINK C3 WASHER i Drop STOPPER into DRAIN BODY E CLIP Pull TAILPIECE up and thread tightly Port into DRAIN BODY Position EXTENSION R
4. s 8 00 a m to 4 00 p m Eastern Time American Standard Inc 1999 34063M B
Download Pdf Manuals
Related Search