American Standard 2555.501 User's Manual
Contents
1. CARTRIDGE SCREWS 2 Remove three SCREWS 3 from FIXATION RING 4 and pull out PRESSURE BALANCING 5 unit Clean SEALS 9 on base of CARTRIDGE 1 Check base of PRESSURE BALANCING UNIT 5 and clean O RINGS 6 Remove CAPS 7 and check O RINGS on inside of CAPS 7 Clean inside sealing surfaces of VALVE BODY 8 Re assemble PRESSURE BALANCING UNIT 5 and CARTRIDGE 1 Tighten all screws Turn on water supply and see above for installing TRIM and HANDLE UNABLE TO MAINTAIN CONSTANT TEMPERATURE Remove PRESSURE BALANCE UNIT 5 Remove CAPS 7 and clean valve thoroughly Examine balancing unit and check condition of O ring on end of piston Piston should move back and forth Order Repair Part M952100 0070A if balancing unit is defective Replace CAPS 7 and install PRESSURE BALANCE UNIT 5 Make sure inlets line up with two holes in bottom of casting Top flange should butt up against top of casting BACK TO BACK INSTALLATION Remove PRESSURE BALANCE UNIT 5 Rotate PRESSURE BALANCE UNIT 5 180 so that the inlets face up and the large outlet port faces down Push PRESSURE BALANCE UNIT 5 in casting make sure inlets line up with holes in bottom of casting Top flange should butt up against top of casting Reassemble FIXATION RING 4 and CARTRIDGE 1 ROTATE 180 LARGE OUTLET LD Sa A 5 L ON INLETS BIY 2 4 BACK TO BACK INSTALLATION EverClean Finish Care Instructions American Standard s Ev2. IF PRESENT When finished soldering flush valve body replace cartridges check stops if present and plaster guard to continue installation Use thread sealant or Teflon tape on threaded connections If the valve is installed on a fiberglass or other thin wall application the PLASTER GUARD 3 can be used as a support m Cut a 4 dia hole in the shower stall m Drill two additional 1 holes to allow access to the stops See Roughing in diagram before starting Connections are m 1 2 female NPT for threaded inlets Connect RISER PIPE 1 to MANIFOLD 2 top outlet marked SHR n For proper positioning the finished wall Remove PLASTER GUARD 3 rotate 90 TE so that indicated screw holes fit MANIFOLD 2 HOT must pe vitii adawa oE ASTER Push CAP on valve place ESCUTCHEON on and GUARD 3 attach with screws Connect hot and cold water supplies Cap off shower pipe 4 For support use pipe BRACES 5 secured to wooden braces With valve turned off turn on water supplies Check for leaks INSTALL TRIM CAUTION Protect finish on SHOWER ARM and SHOWER HEAD when installing When finished tiling the wall remove PLASTER GUARD A and turn off water supply Push CAP 1 over VALVE CARTRIDGE 2 Mount ESCUTCHEON 3 and gasket to valve body with SCREWS 4 Remove PIPE CAP 5 from shower pipe Install SHOWER ARM 6 and SHOWER HEAD 7 ADJUST HOT LIMIT STOP By restricting HANDLE rotation and limiting the amou
3. Installation Instructions PRESSURE BALANCING SHOWER SET 2555 501 with EverClean Finis Congratulations on purchasing your American Standard faucet with EverClean finish found only on American Standard faucets EverClean Finish One wipe effortlessly removes spots Eliminates the need for cleaners and scrubbing Permanent surface protectant remains beautiful for the life of the faucet es Certified ly with ANSI A112 18 1 e EverClean available on Polished Chrome Satin Nickel Freee ee Stainless Steel Polished Brass or any combination of these finishes M968790 REV 1 2 To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Required Tools ROUGHING IN DIMENSIONS To assure proper positioning in relation to wall note roughing in dimensions 3 pt 1 5 8 TO 3 1 4 FINISHED WALL Phillips Screwdriver 1 2 PS Ol 3 Flat Blade Screwdriver i lt 7 OPTIONAL TO Plumbers Putty or Caulking SEE ILLUSTRATION 74 FOR HEAD CLEARANCE ed VERET 3 ae Y INLETS E 1 2 NPT Channel Locks f 40 to 54 SHOWER ONLY OPTIONAL Pee a AN _ THREADED INLETS STOPS Adjustable Wrench BOTTOM OF SHOWER ROUGHING IN eJ fgg 0 Turn off water at main supply heid When soldering remove PLASTER GUARD CARTRIDGES and CHECK STOPS
4. erClean finish will wipe clean with a soft dry cloth A soft cloth with clean water may also be used if desired No additional cleaning products are required DO NOT USE Soaps acid polish abrasives harsh cleaners or a cloth with a coarse surface M968790 REV 1 2
5. nt of hot water allowed to mix with the cold the HOT LIMIT SAFETY STOP 1 reduces risk of accidental scalding To set the maximum hot water temperature of your faucet all you need to do is adjust the setting on the HOT LIMIT SAFETY STOP 1 Turn CARTRIDGE STEM 2 to the OFF position coldest setting before making adjustment to HOT LIMIT STOP 1 Use a flat blade screwdriver to pry free the HOT LIMIT SAFETY STOP 1 Pull forward and rotate counterclockwise one number to limit hot water temperature Use ARROW 3 on CARTRIDGE 4 and NUMBERS 5 on HOT LIMIT STOP 1 for indication INSTALL HANDLE Install HANDLE BUSHING 1 onto CAP 2 Find correct position of HANDLE 3 and push HANDLE 3 onto VALVE STEM 4 Install HANDLE SCREW 5 and push in INDEX CAP 6 Check proper operation of HANDLE Turn on water supply on and test installed fitting Operate valve and diverter spout COLDER Larger Numbers 01357 9111315 Smaller Numbers 9111315 rf M968790 REV 1 2 5 TO GAIN ACCESS TO VALVE FOR SERVICING Pull INDEX CAP unscrew HANDLE SCREW and pull HANDLE off valve stem Remove two SCREWS holding ESCUTCHEON and remove ESCUTCHEON Remove COVER by pulling straight out Shut off water supply by either closing off main water supply or closing off the hot and cold CHECK STOPS on valve VALVE LEAKS WHEN SHUT OFF Remove CARTRIDGE 1 by removing
Download Pdf Manuals
Related Search