American Standard 1340M Series User's Manual
Contents
1. HANDLE use a 3 32 ALLEN WRENCH to loosen three set screws in the HANDLE as shown in Figure A E Remove VALVE CARTRIDGE for cleaning or replacement see in Figure B VALVE E z Reassemble in reverse order Figures C amp D CARTRIDGE TIGHTEN VALVE CARTRIDGE HANDLE L 3 32 ALLEN WRENCH 48mm 1 55 64 45mm 1 3 4DIA 21mm 53 64 DIA 1 2 14 NPSM THREAD HOTLINE FOR HELP 25mm For toll free information and answers to your questions call 1 MAX 1 800 442 1902 Weekdays 8 00 a m to 7 00 p m Eastern Time t 90mm gt IN CANADA 1 800 387 0369 TORONTO 1 905 306 1093 3 9 16 All dimensions are approximate and for reference only Product names listed herein are trademarks of American Standard Inc American Standard Inc 1996 012692D2. Armtrican Standard METERING FAUCET SINGLE TAP PUSH BUTTON FAUCET Installation Instructions 1340 SERIES 1340M SERIES 1340 SERIES FOR COLD AND TEMPERED SUPPLIES 1340M SERIES INCLUDES BELOW DECK MIXING VALVE WITH STRAINER Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please read these instructions carefully before you begin WARNING SUPPLY INLET MUST BE FILTERED WITH A GO MESH SCREEN USE AMERICAN STANDARD MIXING VALVE WITH STRAINER OR COMMERCIAL 6O MESH STRAINER MIXING STRAINER VALVE ASSEMBLY BODY AERATOR KEY ESCUTCHEON KIT OPTIONAL DECK WASHER eee BRASS LOCK RING AND SCREWS RISER TUBE _ NOT INCLUDED 1340 SERIES SET SCREWS m HANDLE so w SE SPRING Sx RETAINING RING LEVER VALVE CARTRIDGE HANDLE RETAINER 1 ASSEMBLING ESCUTCHEON KIT OPTIONAL CAUTION Turn off hot and cold water supplies before beginning Peel off paper backing from PADS and stick both PADS to underside of ESCUTCHEON about 1 4 from ends Peel off paper backing from WASHER and stick WASHER into circular groove of SUPPORT PLATE Place SUPPORT PLATE PAD WASHER of ESCUTCHEON with WASHER visible E Apply a bead of PUTTY around the inside of ESCUTCHEON edge Turn ESCUTCHEON over and center it with SUPPORT PLATE over center hole o
3. f sink deck in center SUPPORT gt ESCUTCHEON 2 ASSEMBLING MOUNTING KIT Certified to comply with ANSI A112 18 1M U S PATENT NOS 012692D LOCK RING E Thread 3 SCREWS into LOCK RING E SCREWS should extend half way thru RING Ye SCREWS MOUNTING FITTING Install faucet through the ESCUTCHEON being sure the rubber GASKET is between the FAUCET and the ESCUTCHEON Install brass WASHER and turn LOCK RING onto SHANK Tighten 3 SCREWS in the LOCK RING to secure fitting FOR 1340 SERIES ONLY Warning GO MESH STRAINER required for supply water Install RISER TUBE not included and tighten SUPPLY NUT Connect RISER TUBE to COLD or TEMPERED water supply FOR 1340M SERIES Connect FLEXIBLE FAUCET SUPPLIES 1 2 faucet cone on one end 3 8 compression on the other to the MIXING VALVE INLETS and the VALVE hot cold wall stops ADJUSTMENT The FLEXIBLE FAUCET SUPPLIES are NOT T included Turn on WALL lt FAUCET STOPS and check J E for leaks J With WALL STOPS open and water flowing adjust MIXING VALVE to temper water STRAINER COLDER 4 TO OPERATE gt 40 sec P N e S amp S aaa Stop 10 sec A Automatic minimum P v D l Lift off retaining ring then slide out lever horizontally E Press down to start Cycle time is factory set but can be changed as shown 5 TO SERVICE TIGHTEN SET SCREWS E TO remove
Download Pdf Manuals
Related Search