Amana UMTK30 User's Manual
Contents
1. S SS 27 Trim Frame 30 Trim Frame2. e Locate and disconnect the power to any electrical circuits that could be affected by installing this oven IF YOU DO NOT DISCONNECT THE POWER YOU COULD GET AN ELECTRICAL SHOCK A WARNING To avoid personal injury wear gloves when handling the metal parts Parts are sharp and can cause cuts and abrasions Electrical rating of this oven e 120 VAC 60 Hz 13A 1100W e You need a DEDICATED 120 VAC 60 Hz 20 A fused electrical supply located in the cabinet with the microwave as close as possible to the microwave serving only the microwave e Check with a qualified electrician if you are not sure whether the oven is properly grounded or if you do not completely understand the grounding instructions e Do not use a fuse in the neutral or grounding circuit A WARNING Improper grounding could result in electric shock or other personal injury e Save these instructions for the local electrical inspectoris use e f there is an electrical short circuit grounding reduces the risk of electrical shock by providing an escape wire for the electric current This appliance is equipped with a cord having a grounding wire with a grounding plug e Place the plug into a properly installed and grounded outlet Amana does not recommend use of an extension cord e Keep the power cord dry and do not pinch or crush it e Do not under any circumstances remove the power supply cord grounding prong e This appliance MU
3. ST be grounded Three prong Grounding plug Properly polarized and grounding outlet A WARNING If you do not use the microwave oven as instructed you could be exposed to excessive microwave en ergy Do not expose yourself to excessive microwave energy e DO NOT try to operate the microwave oven with the door open e DO NOT tamper with or defeat the safety interlocks e DO NOT place objects between the microwave oven front face and the door e DO NOT allow soil or cleaner residue to build up on the flat surfaces around the microwave oven door e DO NOT operate the microwave oven if it is damaged e The microwave oven door must close properly to operate safely e DO NOT USE THE MICROWAVE OVEN e If the door is bent e f the hinges or latches are broken or loose e If the door seals sealing surfaces or glass is broken e DO NOT ATTEMPT TO ADJUST OR REPAIR THE OVEN YOURSELF e t should be adjusted and repaired by a qualified technician who can check for microwave leakage after repairing the oven A WARNING If you do not mount the oven as instructed you risk personal injury and or property damage A WARNING Before you begin installing the oven PLACE A PIECE OF THE CARTON OR OTHER HEAVY MATERIAL a blanket over the countertop or cooktop to protect it Do not use a plastic cover Failure to protect these surfaces could result in property damage 1 SET installment in Brack
4. UMTK30 27 Built In Trim Kit Installation Instructions For use with the following microwave oven ACM2260B and UMC5200BA UMC5200 Proper installation is the installer s responsibility Write the model amp serial numbers on the owner s manual The model number label is located on the oven front UL Listed For use over electric heat source models Wall Ovens UMC5200BAB BAW BAS e JMC5200BAW e AMC2206BAB BAW BAQ BAS A WARNING To avoid risk of electrical shock personal injury or death disconnect power to wall outlet before begin ning installation Parts Tools and Materials The following parts are supplied with the oven Trim Frame Template 1 template 2 Bracket Base Bracket Left Bracket Top 1 required 1 extra v2 Screw 14 required 6 extra Tools required to perform installation e Phillips Screwdriver e Saw Electric or Hand e Drill with 7 64 drill bits Electric or Hand e Tape Measure e Pencil e Framing Square e Level Shipping Weight e Approximate shipping weight is Ibs Cutout Dimensions Dimensions ae o W Electric Heat Source Model A WARNING To avoid risk of electrical shock personal injury or death e Before drilling into the wall note where electrical outlets are and where electrical wire might be concealed behind the wall YOU COULD GET AN ELECTRICAL SHOCK if you contact electrical wire with the drill bit
5. et Base Leave the screws protruding from With product use boxed screw 4 x 20 mm a minimum of 3 5 to a maximum of 4 5 mm 4 Remove 4 screws from the lower right and left parts Fix 1 screw at the bottom of cabinet with use of of outer panel place SET in Bracket Base and fix template 1 it by tightening 4 screws again 2 Installment of Bracket Left 4 SET installment in cabinet Push SET into the cabinet inside so that the fixed bottom screw of cabinet can place in the hole of Bracket Bottom Push SET in until the bent part of front Bracket Base touches the front of cabinet Assemble the Bracket Left to outer panel Installment of Bracket Bottom 7 Place Bracket Bottom on Bracket Base like picture B Make holes of position A fit to Bracket Base s and fix screws after making holes with a 7 64 drill or a 35 drill l i 8 Installment of Trim Frame Install Bracket Bottom by tightening screws at screw points Install Trim Frame to make contact cabinet 6 Installment of Bracket Top Fix 2 screws each at the upper and lower parts of Trim Frmae with the door open Fix it by color screw With template 2 make 2 holes each at the upper right and left parts of cabinet Others for the extra Fix Bracket Top according to the holes Trim Frame Dimensions Depth of trim Frame is 7 8
Download Pdf Manuals
Related Search