Amana NGD5800DW Dimension Guide
Contents
1. Gas Dryer Amana PRODUCT MODEL NUMBERS NGD5700B NGD5800D DRYER DIMENSIONS Front view Side view a 27 51 686 mm a 1220mm 156 mm 143 s 365 mm a 253 4 654 mm 24 in min 155 cm 383 4 Min 984 mm 39 Max 990 mm 53 4 146 mm 31 2 89 mm Back view A 61 4 A 159 mm 3 4 10 3 lt 7 18 mm 257 mm Approx measurement 1 Recommended installation clearances dryer only 297 e Water inlet 759 mm Steam Models Only p otmen 53 4 146 mm 31 2 A 89 mm 76 mm 48 in min 310 cm a G1 g A 7 5 Approx measurement 127 mm oi NS N NOTE Most installations require a minimum of 5 127 mm clearance behind dryer for exhaust vent with elbow See Venting Requirements A ae qu M4 5 A 0 0 mm spacing is allowed Installation spacing for recessed area or closet installation All dimensions show recommended and minimum spacing allowed m Additional spacing should be considered for ease of installation and servicing E Additional clearances might be required for wall door floor moldings dryer venting and gas line E Additional spacing should be considered on all sides of the dryer to reduce noise transfer For closet installation with a door minimum ventilation openings in the top and bottom of the door are requi2. mended Styles E Louvered Hood T Box Hood Acceptable Style e Angled Hood Because Whirlpool Corporation policy includes a continuous commitment to improve our products we reserve the right to change materials and specifications without notice Determine vent path Select route that will provide straightest and most direct path outdoors Plan installation to use fewest number of elbows and turns When using elbows or making turns allow as much room as possible m Bend vent gradually to avoid kinking m Use as few 90 turns as possible Determine vent length and elbows needed for best drying performance m Use the Vent System Charts on the next page to determine type of vent material and hood combinations acceptable to use NOTE Do not use vent runs longer than those specified in Vent System Charts Exhaust systems longer than those specified will Shorten life of dryer m Reduce performance resulting in longer drying times and increased energy usage Standard Vent System Chart Number of Type Angled 90 elbows of vent hoods Fo Rigid metal 64 ft 20 m L 4 Rigid metal 54 ft 16 5 m ee Rigid metal 44 ft 13 4 m Rigid metal 35 ft 10 7 m Rigid metal 27 ft 8 2 m Dimensions are for planning purposes only For complete details see Installation Instructions packed with product Specifications subject to change without notice
3. red Louvered doors with equivalent ventilation openings are acceptable W10573707B m Companion appliance spacing should also be considered 04 2014 INSTALLATION REQUIREMENTS GAS SUPPLY REQUIREMENTS Gas supply This dryer is equipped for use with Natural gas Dryer can be converted to L P as When rigid pipe is used it should be 1 2 IPS When acceptable to the gas supplier and local codes 3 8 approved tubing may be used for lengths under 20 ft 6 1 m For lengths over 20 ft 6 1 m larger tubing should be used Pipe joint compounds resistant to the action of L P gas must be used An individual manual shutoff valve must be installed within 6 ft 1 8 m of the dryer in accordance with the National Fuel Gas Code ANSI 2223 1 ELECTRICAL REQUIREMENTS A 120 volt 60 Hz AC only 15 or 20 amp fused electrical supply is required A time delay fuse or circuit breaker and a separate circuit are recommended WATER STEAM MODELS ONLY REQUIREMENTS The dryer must be connected to the cold water faucet using new inlet hoses Do not use old hoses Do not overtighten Damage to the coupling can result VENTING REQUIREMENTS Exhaust venting Exhaust your dryer to the outside 4 102 mm diameter vent is required Rigid or flexible metal exhaust vent must be used Do not use plastic or metal foil vet Exhaust hood must be at least 12 305 mm from the ground or any object that may be in the path of the exhaust Exhaust hoods Recom
Download Pdf Manuals
Related Search