Home
Allied Telesis SB244-03 User's Manual
Contents
1. DHCP Network affecting No Inuse DHCP entries that are displayed in the SHOW DHCP CLIENT command will now expire and be reclaimed PCR 02494 Module IPv6 Network affecting No It was possible to add the same IPv6 prefix to different IPv6 interfaces This issue has been resolved PCR 02497 Module PPP Network affecting No The wrong error message was displayed if PPP compression over L2TP was attempted The correct message is now generated stating that the CREATE PPP command is invalid PCR 02499 Module IPG Network affecting No Some parameters in the SET IP IGMP command had incorrect ranges This issue has been resolved The correct ranges are SET IP IGMP LMQT 1 255 LMQC 1 5 QUERYINTERVAL 1 65535 QUERYRESPONSEINTERVAL 1 255 ROBUSTNESS 1 5 TIMEOUT 1 65535 PCR 02502 Module Ping IPv6 Network affecting No If multiple IPv6 interfaces shared the same link local address pings to the link local address sometimes failed This issue has been resolved PCR 02503 Module NVS Network affecting No Loading files to NVS caused a fatal error This issue has been resolved PCR 02504 Module SWI Network affecting No A warning was not given if the egress limit for a port was not set to a multiple of 64 This issue has been resolved PCR 02507 Module SWI Network affecting No ARP entries on the SwitchBlade 4000 Series Switch controller card are now updated correctly if a device changes to a differen
2. for Patch SB244 01 Base Software Release File sb 244 rez Patch Release Date 23 Oct 2002 Compressed Patch File Name sb244 01 paz Compressed Patch File Size 84666 bytes Patch SB244 01 includes the following enhancements PCR 01285 Module OSPF Network affecting No When an interface went down or was disabled on an AS border router the external routes were not removed from the routing domain Such routes are now removed by premature aging PCR 02353 Module SWI Network affecting No The learning unit was locking under heavy load This could result in pings to a network device failing and over an hour all dynamic MAC addresses could be lost Sometimes a large number of pause frames were generated by the system This issue has been resolved PCR 02359 Module IPG Network affecting No When an IP Multihomed interface was used as an OSPF interface neighbour relationships were only established if the IP interface for OSPF was added first in the configuration Now OSPF establishes neighbour relationships regardless of the IP Multihomed interface configuration order PCR 02361 Module SWI Network affecting No The SwitchBlade mirror port field on the second instance of a switch chip was displaying as though it was the first instance This issue has been resolved PCR 02394 Module IPG SWI DVMRP Network affecting No The following issues have been resolved e IP route updating was not working correctly e IGM
3. CR 02428 Module IPV6 Network affecting No Link local address behaviour was incorrect Also the PUBLISH parameter was not updated by the SET IPV6 INTERFACE command or displayed in the SHOW IPV6 INTERFACE command These issues have been resolved PCR 02450 Module IPV6 Network affecting No Large local packets were not being fragmented Also the More Fragment flag in the IPv6 fragment header was not being set correctly These issues have been resolved PCR 02452 Module IPV6 Network affecting No Received Router Advertisements RAs were discarded when the interface was enabled to send RAs This issue has been resolved PCR 02458 Module SWI GUI Network affecting No The status page in the GUI was not displaying correctly This issue has been resolved PCR 02459 Module CORE Network affecting No The SLVPASSWORD string in the ENABLE SYSTEM SYSR SLVFEATURE and ENABLE SYSTEM SYSR SLVRELEASE commands was not copying correctly This issue has been resolved Patch B244 03 for Software Release 2 4 4 C613 10349 00 REV C Patch B244 03 For SwitchBlade 4000 Series Switches and AT 9800 Series Switches 5 PCR 02460 Module SWI Network affecting No Sometimes a port reported an interface as being down but the port counters kept incrementing This issue has been resolved PCR 02461 Module SWI Network affecting No The CREATE TRIGGER MODULE SWITCH command now recognises ports in x y notation when specifying the PORT parameter
4. P snooping behaviour was incorrect e The SHOW DVMRP FORWARDING command displayed incorrect port numbers PCR 02396 Module DHCP Network affecting No DHCP RENEW request messages are now unicast as defined in the RFC not broadcast PCR 02397 Module DVMRP Network affecting No After a prune lifetime had expired the interface was not joined back to the DVMRP multicast delivery tree This issue has been resolved Patch SB244 03 for Software Release 2 4 4 C613 10349 00 REV C Patch B244 03 For SwitchBlade 4000 Series Switches and AT 9800 Series Switches 7 PCR 02398 Module IPV6 Network affecting No The following issues have been resolved e It was possible to assign the same network on different IPV6 interfaces e The loopback address was being added to other interfaces e The tunnel configuration was not showing correctly in IPV6 configuration commands e RIPv6 now sets the metric of routes for interfaces that are DOWN to 16 and immediately sends responses when the link status of VLAN interfaces changes PCR 02401 Module IPV6 Network affecting No Neighbour discovery and PIM6 caused a fatal error when IPv6 was not enabled or when the IPv6 feature license was not present This issue has been resolved PCR 02406 Module IPV6 Network affecting No A Router Alert option has been added Also the SHOW IPV6 MLD INTERFACE command now works correctly PCR 02407 Module IPG Network affecting No ICMP was sending too many messa
5. PCR 02462 Module SWI Network affecting No A fatal error occurred on SwitchBlade 4000 Series Switches when booting from a script that added ports to a trunk group that was hot swapped out This issue has been resolved PCR 02463 Module DVMRP IPG Network affecting No Support for multi homed interfaces has been added PCR 02467 Module CORE Network affecting No The board descriptions have changed for some instances of AT 9800 Series Switches PCR 02468 Module SWI Network affecting No Whena Telnet session was closed SWITCH debug was not disabled if it had been enabled for the Telnet session This issue has been resolved PCR 02469 Module TM Network affecting No After an ASYN port test the port is now reset to its pre test state if the test was started by a user connected to the same ASYN port PCR 02470 Module SWI Network affecting No The Built in Self Test failed on SwitchBlade chassis This issue has been resolved PCR 02476 Module VRRP CORE Network affecting No The configuration was not restored correctly after a line card was hot swapped out This issue has been resolved PCR 02478 Module SCRIPT Network affecting No A string compare error was occurring in the conditional statement of the script This issue has been resolved Patch SB244 03 for Software Release 2 4 4 C613 10349 00 REV C Patch Release Note Features in SB244 01 Patch file details are listed in Table 3 Table 3 Patch file details
6. PCR 02471 Module IPG Network affecting No The counter for transmitted ARP packets was incorrect This issue has been resolved PCR 02480 Module SWI Network affecting No On SwitchBlade 4000 Series Switches the MIB browser could not see the slave controller card This issue has been resolved PCR 02483 Module SWI TM Network affecting No When SwitchBlade 4000 Series Switches were operating with a full set of line cards and the test module was enabled for all interfaces an excessive amount of traffic was generated This issue has been resolved PCR 02486 Module SWI Network affecting No VLAN number 4077 could not be created This issue has been resolved PCR 02487 Module SWI Network affecting No When there were 4000 VLANs executing the DESTROY VLAN ALL command caused a fatal error This issue has been resolved PCR 02490 Module IPv6 Network affecting No The ADD IPV6 ND command was not displayed by the SHOW CONFIGURATION DYNAMIC command This issue has been resolved PCR 02491 Module IPG Network affecting No The ARP cache is now updated when a gratuitous ARP request or reply packet is received Patch SB244 03 for Software Release 2 4 4 C613 10349 00 REV C Patch B244 03 For SwitchBlade 4000 Series Switches and AT 9800 Series Switches 3 PCR 02492 Module SWI Network affecting No 288MB RDRAM was initialised incorrectly resulting in unpredictable behaviour This issue has been resolved PCR 02493 Module
7. Patch Release Note Patch SB244 03 For SwitchBlade 4000 Series Switches and AT 9800 Series Switches Introduction This patch release note lists the issues addressed and enhancements made in patch SB244 03 for Software Release 2 4 4 on existing models of SwitchBlade 4000 Series Switches and AT 9800 Series Switches Patch file details are listed in Table 1 Table 1 Patch file details for Patch SB244 03 Base Software Release File sb 244 rez Patch Release Date 26 Nov 2002 Compressed Patch File Name sb244 03 paz Compressed Patch File Size 250571 bytes This release note should be read in conjunction with the following documents E SwitchBlade Documentation Set for Software Release 2 4 3 Document Number C613 03042 00 Rev E and Release Note for Software Release 2 4 4 for SwitchBlade 4000 Switches and AT 9800 Series Switches Document Number C613 10342 00 Rev A available on the Documentation and Tools CD ROM packaged with your switch or from www alliedtelesyn co nz documentation documentation html m AT9800 Series Switches Documentation Set for Software Release 2 4 3 Document Number C613 03044 00 Rev B and Release Note for Software Release 2 4 4 for SwitchBlade 4000 Switches and AT 9800 Series Switches Document Number C613 10342 00 Rev A available on the Documentation and Tools CD ROM packaged with your switch or from www alliedtelesyn co nz documentation documentation html WARNING Using a patch for a diffe
8. eated as 0 0 0 0 PCR 02420 Module SWI Network affecting No On GBICs the link was forced up when the transmit fibre was removed Once up the link could not be taken down again by removing the transmit fibre This issue has been resolved PCR 02423 Module SWI Network affecting No IGMP messages sometimes caused a fatal error This issue has been resolved PCR 02425 Module IPG Network affecting No Multicast downstream groups are now added and deleted correctly Errata AT 9800 Series Switches do not have Ethernet interfaces for example eth0 Previously released documentation incorrectly states that these interface types are valid AT 9800 switch ports are Ethernet ports and these are referenced in commands with the PORT parameter IPSec and ISAKMP are not available on the 2 4 4 release for SwitchBlade 4000 Series Switches and AT 9800 Series Switches Availability Patches can be downloaded from the Software Updates area of the Allied Telesyn web site at www alliedtelesyn co nz support updates patches html A licence or password is not required to use a patch Patch B244 03 for Software Release 2 4 4 C613 10349 00 REV C
9. ges back as responses to fragmented packets This issue has been resolved PCR 02409 Module IPG Network affecting No A warning now appears when the DELETE IP INTERFACE command is executed before the DELETE DVMRP INTERFACE command PCR 02410 Module VRRP Network affecting No VRRP pre empt mode was not working with advertisement updates of 1 second or more because this did not allow for interface start time on startup Now a check is made to verify that interfaces are UP before timers are started PCR 02413 Module IPG IPX2 Network affecting No Static IP ARP entries could not be added to hardware at boot time Also an IPX circuit could not be deleted from hardware These issues have been resolved PCR 02416 Module DVMRP IPG Network affecting No Multicasting forwarding was not working correctly This issue has been resolved PCR 02417 Module VLAN IPG Network affecting No The IGMP port list was not updating correctly when a port went down This issue has been resolved PCR 02418 Module IPV6 Network affecting No ICMPv6 was returning an error for non zero fragment offsets This issue has been resolved Patch SB244 03 for Software Release 2 4 4 C613 10349 00 REV C Patch Release Note PCR 02415 Module IPG Network affecting No Packets with a RIP source address and next hop address that are not on the same subnet as the interface will now be processed If the received next hop is not on the same subnet it is tr
10. rent model or software release may cause unpredictable results including disruption to the network Information in this release note is subject to change without notice and does not represent a commitment on the part of Allied Telesyn International While every effort has been made to ensure that the information contained within this document and the features and changes described are accurate Allied Telesyn International can not accept any type of liability for errors in or omissions arising from the use of this information MAW Allied Telesyn Simply connec ting the world Patch Release Note Features in SB244 03 Patch SB244 03 includes all issues resolved and enhancements released in previous patches for Software Release 2 4 4 and the following enhancements PCR 02414 Module IPV6 SWI IPG VLAN Network affecting No MLD snooping is now supported on AT 9800 Series Switches and Rapier i Series Switches PCR 02451 Module IPG PIM VLAN SWI Network affecting No The following issues have been resolved e PIM was disabled when the RESET IP command was executed e PIM reverse path check was not working correctly e PIM_DM assert was not working correctly e DVMRP messages were not being flooded correctly e Executing the SHOW PPP command sometimes caused a fatal error e IP forwarding was not working correctly on SwitchBlade 4000 Series Switches e Changes have been made for supporting non contiguous IP subnetworks
11. t line card PCR 02509 Module DVMRP Network affecting No The source net mask has been removed from DVMRP prune graft and graft ack messages PCR 02511 Module Ping Network affecting No Executing the PING command sometimes caused a memory leak This issue has been resolved PCR 02516 Module IPG Network affecting No Untagged IGMP packets were erroneously sent out of tagged ports This issue has been resolved Patch SB244 03 for Software Release 2 4 4 C613 10349 00 REV C Patch Release Note Features in SB244 02 Patch file details are listed in Table 2 Table 2 Patch file details for Patch SB244 02 Base Software Release File sb 244 rez Patch Release Date 1 Nov 2002 Compressed Patch File Name sb244 02 paz Compressed Patch File Size 57728 bytes Patch SB244 02 includes all issues resolved and enhancements released in previous patches for Software Release 2 4 4 and the following enhancements PCR 02406 Module IPV6 Network affecting No Some parameters in MLD specific query messages were not working correctly This issue has been resolved PCR 02426 Module IPV6 Network affecting No The ENABLE IPV6 MTUDISCOVERY and SET IPV6 MTU INTERFACE commands were not displayed in the SHOW CONFIGURATION DYNAMIC command This issue has been resolved PCR 02427 Module DHCP Network affecting No DHCP entry reclaim checks are now delayed by 10 seconds if the entry is unroutable because the interface is not up P
Download Pdf Manuals
Related Search
Related Contents
Conseils pour des vacances d`été sans soucis Télécharger - Digivue France 多回路電力レコーダ - 東光東芝メーターシステムズ株式会社 Manuale di istruzioni Bosch Power Tools Laminator 36 User's Manual M•ONE & M•ONE XL Organe de réglage 115 à 230 V/1 kW 734 22 Bea-fon SL215 Sony VGN-BX500 User's Manual Copyright © All rights reserved.
Failed to retrieve file