Allied Telesis CG-WLBARGMO User's Manual
Contents
1. Auto obtain IP DHCP e g Cable Modem Fixed IP O Float IP PPPoE 2 Enter the network setting provided by your ISP Then click on Next Setup Wizard Fixed IP address Please manually setup your network Please configure your network from infomation provided by your ISP WAN port IP address p ooo Subnet Mask 255 255 255 0 0 0 0 0 0 0 0 0 Default Gateway DNS Server 1 WLBARGMO Manual 3 Click on Save to perform connection tests Setup Wizard setup completed Save please click on save Test result Prepare for network testing Please wait 7 seconds 4 Within seconds the result of the connection test will be appeared in the dialogue box to indicate the connection status When Connection OK appears click on Close Setup Wizard Setup completed Save please click on save Test result Prepare for network testing Please wait 0 seconds Fixed IP connection OK IP Address 10 15 1 41 Subnet Mask 255 255 255 0 Default Gateway 10 15 1 254 DNS Server 1 0 0 0 0 DNS Server 2 NA WLBARGMO Manual 5 Open the web browser IE 6 0 and test with any website for testing the connection Note If the connection to the website fails Please make sure the data you entered are correct or any mistake occured in the process of the installation such as the LAN WAN connections After verifyi2. WLBARGMO Manual 4 Wireless Network Connection Properties PR General Wireless Networks Advanced Use Windows to configure my wireless network settings Available networks To connect to an available network click Configure i corega a 4 ATT W OFFICE E ia a Prefered networks Automatically connect to available networks in the order listed below Move up Move dowr Add Remove Properties Learn about setting up wireless network 2 Go Control Panel gt Network connection again 5 Right click Wireless network connection select Available wireless network connection choose one available network e g corega and click Connect Wireless Network Connection IR The following wireless network s are available To access a wireless network select it from the list and then click Connect Available wireless networks corega ATTW OFFICE i MPMR This wireless network is not secure Because a network key WEP is not used for authentication or for data encryption data sent over this network might be subject to unauthorized access ix gt Allow me to connect to the selected wireless network even though it is not secure IF you are having difficulty connecting to a network click Advanced 3 Connection status will appear in the bottom right of the screen Wireless Network Connection corega Speed 54 0 Mbps Signal Strength
3. KEV C Keys WPA shared hey orm 53 0 3 Radus Server S tae Cancel Wack 1 Select WEP from Authentication menu 2 Select WEP from Cipher menu 3 Select 64 bit or 128 bit from the Encryption menu Type encryption code in Key1 3 4 Na SoA ee SNA X64 bit hex 0 9 a f 10 digits in total 4128 bit hex 0 9 a f 26 digits in total Or you can click Generate Key to obtain a password automatically a Enter any character in the column of Auto generate WEP b Click Generate Key c Passwords will be generated automatically in the columns of Key1 Key4 PS Every kind of network adapter might have different encryption ways so Generate Key isn t recommended Check before selection 5 Recommended to keep default value of DTIM 6 Save your settings by Save WLBARGMO Manual 5 2 WPA Setting WPA is encrypted by a periodic update making it more difficult to be hacked Home users and company users are recommended to use lt WPA PSK gt and lt WPA EAP gt respectively lt WPA PSK gt 1 Select WPA2 PSK or WPA WPA2 PSK in the column of Authentication Recommended a WPA2 PSK The 2nd generation encryption technology performs stricter protection than ever Before selection please check the function avail ability of your network adapter or select b b WPA WPA2 PSK If selected encryption type will be defined automati cally according to the corre
4. Status Log Display E mail Function When there is DoS attach auto warning email will be sent Mail Address SMTP Server Name Username Password N7 FAQ When the installation fails or the connection doesn t succeed it s recommend ed to take the following actions 1 Find your problem in the troubleshooting collection 2 Search on our official website at http www corega asia com for the latest information of this product 3 Go to our official website at http www corega asia com gt click Support gt select the Online Customer Support item gt fill the form page and note following information We will contact you as soon as possible Product name e g WLBARGMO e Firmware version access the management program to check e Your ISP service name e Windows system e g Windows98 2000 XP and so on e WEB browser Version e g IE5 0 5 5 6 0 and so on e Network adapter manufacturer and its driver version e Connection way fixed IP dynamic IP or PPPoE dial up connection e What is your problem and situation e g unable to internet e What is the error message or picture Q1 Not able to connect to the Internet Please make sure if the below processes are complete or not 1 Is your subscription to ISP expired 2 Have the powers of all relevant devices been switched on or have cables or plugs been connected correctly 3 Has th
5. 10 15 1 2 WLBARGMO Manual 5 Open the web browser IE 6 0 and test with any website for testing the connection Note If the connection to the website fails Please make sure the data you entered are correct or any mistake occured in the process of the installation such as the LAN WAN connections Mfter verifying that repeat these setps in the section 4 2 Establishing the Wireless Internet Connection So far you should be able to connect to the Internet wirelessly However please be reminded that your network is not safe and the connection is open to anyone Please consult Chapter 5 Wireless Security Configuration for security setting Wireless connection is illustrated as following 4 2 1 Adjust the Antennas In order to keep WLBARGMO in the best status please refer to the following figure Please confirm that the antennas are adjusted as the figure bellow ZN AN File Server na ADS L Cable WLBARGM O Modem 802 119 4 2 2 Setup Wireless Adapter Hereunder is the setting on Centrino Notebook as an example for wireless adapters in other brands please refers to the original manuals lt Windows XP SP1 O S gt 1 Go Control Panel gt double click on Network connection gt right click on Wireless Network Connection gt select properties gt click on Wireless Network tab gt select Use Windows to configure my wireless networks setting and press OK
6. Not response to WAN ping request Disable v O High Security Firewall Medium Security O Low Security lt Security setting Connection control gt This function can limit or control some certain networking services 1 Enter the range of limited IP address 2 Select one of limit stop networking services 3 Select one of protocol Enter the range of limited port number Security Setting Connection Control 3 A ea ee NA Limited IP Range 1 192 168 1 Limited Serace 2 User Detinmten w Pratacal 3 OTCP OVOP Opeth Limited Port Range af fs Schedule Description 5 Aways 6 Cee aa Connection Conmol Table Max 10 records Status Limited IF Range Limited Service Schedule Operate 5 Select one of the time schedule limitations After clicking on Time Setting button a time schedule table will show up once complete the setting Edit Schedule Mana T Weak Start Tews Khan Ena Tina hhimmj syay CICI a Sungay JIL CH Maa io Ctr Tusasay Jt L H Wednesday em f as Tian aan Trara Cii C C pay Saron rr i Tiheda Table Mau P0 neoini j Hala Mara Operate oe I Geek 6 Please click on save button to store the information q 65 m r xsz r rr a WLBARGMO Manual Security setting filter list gt This function can forbid users to access certain website on the Internet 1 Enter the forbidden URL or keywords 2 Then click save to
7. Download Options File Helpers Cane A Network Configuration WLBARGMO Manual 4 1 Quick Network Configuration Basic configuration is required before connection your computer to the inter net via WLBARGMO The connection methods may be differed by your contract to the ISP Please reconfirm your connection conditions with your ISP prior to configure this router The configuration procedures are as follow Note Anti virus or Firewall software may prevent this router from being set up properly Please close such software through out the setting of WLBARGMO 1 Open the Web browser Internet Explorer 6 0 If you use dial up network such as PPPoE and are using Windows 2000 98 ME O S The Dial up Network window will pop up do not connect to the Internet right now and close the window 2 Type 192 168 1 1 in the browser s address bar press Enter Note 192 168 1 1 is the IP address for configuring CG WALBARGMO and is not corega s company public internet address After you have completed the configuration connect to http www corega asia com for testing the connection 3 When log in screen is appeared type root for the username and leave empty for the password Press Submit Username root J Password 4 Please select the language e g English gt Select your region e g Singapore gt Click Apply Regional amp Language Options Lan
8. Good Status Acquiring network address WLBARGMO Manual lt Windows XP SP2 O S gt 1 Go Control Panel double click on Network connection right click on Wireless Networks Connection select properties click on Wireless Network tab select Use Windows to configure my wireless networks setting and press OK 4 Wireless Network Connection Properties PR General Wireless Networks Advanced Use Windows to configure my wireless network settings Available networks To connect to disconnect from or find out more information about wireless networks in range click the button below View Wireless Networks Preferred networks Automatically connect to available networks in the order listed below Move up Move dow Remove Properties Learn about setting up wireless network configuration 2 Go Control Panel gt Network connection again gt right click Wireless network connection select Available wireless network connection e g corega and click Connect i Wireless Network Connection EET Choose a wireless network a Refresh network list Click an item in the list below to connect to a wireless network in range or to get more information 2 Set up a wireless network i RD SW TEST for a home or small office i Hf Security enabled wireless network Related Tasks EDEEORA JD Learn about wireless Y Security enabled wireless network WPA
9. form gt Click Submit Q7 How to acquire your PC s IP address A If you want to check your PC s IP address via the product you may refer to the below steps a S WLBARGMO Manual lt Windows XP 20005 1 Click Start gt Programs gt Command prompt 2 Input ipconfig gt Enter 3 Confirm IP address which sould be 192 168 1 x If the IP is incorrect please enter 1 byte character as ipconfig renew gt Press Enter lt Windows Me 98 95 gt 1 Click Start gt Click Run 2 Input winipcfg in the column gt press Enter 3 Select your network adapter to display IP address The IP should be 192 168 1 x if none please click Release gt Click Renew Q8 How to reboot the product A Reboot to get new setting values applied The steps are as follows open the management program gt Click on Management gt Click on Proceed in the Reboot column Note The definitions of Reboot Firmware update and Reset to default settings are different Please make sure of your intention before proceeding Q9 How to reset to default settings A If you forget the password get failed in setting or product hang up you can reset the product s settings to default values 1 Use a spindle item e g a clip to press Init button in the back side of the product until Status lights up with red 2 After the red light goes out the system will restore its default value
10. obtain the Ethernet card s MAC address Then press Next Setup Wizard auto obtain IP address Please manually setup your network WAN port MAC address 90 50 1 8 21 CF 8A MAC address clone WLBARGMO Manual 3 Click on Save to perform connection tests Setup Wizard Setup completed Save please click on save Test result Prepare for network testing Please wait 7 seconds 4 Within seconds the result of the connection test will be appeared in the dialogue box to indicate the connection status When Connection ok appears click on Close Setup Wizard Save please click on save Test result Prepare for testing Please wait 0 seconds DHCP connection OK IP address 10 15 1 72 subnet mask 255 255 255 0 Default gateway 10 15 1 254 DNS server 10 15 1 2 5 Open the web browser IE 6 0 and test with any website for testing the connection Note if the connection to the website fails Restart your Cable Modem and check the installation of CG WLBARGMO properly such as the LAN WAN connections After verifying that restart this chapter again for installation WLBARGMO Manual 4 1 2 Fixed IP 1 If you are subscribing Fixed IP connection from your ISP then select Fixed IP and click on Next Setup Wizard Network Connection WAN setting Please configure network connection WAN setting Please select your connection type
11. same setting otherwise the connection can t succeed 3 Recommended to keep default values of DTIM 4 You may click RADIUS Server for parameter settings but check with MIS staff before setting Wireless Setting 802 11 g b Security Setting CG Encryption Auto generate WEP WEP KEY 16 Gecenals O 9 a f KEYI gt KEY2 KEY KEY4 WPA shared key SCII ke haracter 6 decimals 64 characte Sfom egy _ J Radius Server 4 Fates Severseup SC Ca 5 Save your settings by Save Function Introduction The chapter will briefly introduce all functions of this product and spell them out Log in the management program and the below interface will appear Status Firmware Version Ver 100 Operating Time 58 Minute 27 Second MAG address DSI 18 71 6708 Subnet Mask i 265 255 255 0 IP Address 192 158 1 1 LAH Status DHCF Enable CHCP srarciF 192 168 1 71 CHEF end IF 192 166 150 MAG address Of Sh 18 21 6F 08 Mode i 11b 9 Enable Wiralasa iii Security Open System Disable Channel 11 E8810 corega Status Wireless ACCESS Enable MAG address Of Sh 18 21 EF A WAH i Fixed IP IP Addraze 00 00 WAH Status Subnet Mask 0 00 0 Default Gateway 0 0 00 DMS Server i DOO UNG Server z B D Petresh 6 1 Features lt Mode gt Mode Mode Router Mode Wireless Enable Cancel Wireless function Select and switch to Router wireless broadband router or AP Acess po
12. 802 1 1g products It also has 3 antennas which can improve transmit quality Moreover WL BARGMO supports security settings such as WEP WPA WPA2 PSK and 802 1x WDS and WMM functions are also supported With extensive functions and superior efficiency WLBARGMO is the best choice for users seeking for a high quality and broad coverage area wireless broadband Router 1 1 Package Contents Check the listed contents thoroughly before installation In case of discrepancy to the list below check with your local dealers Wireless 108Mbps Broadband Router Power Adapter Detachable Antenna Flat UTP Cable Product Stand with Mounting Screws Wall Mount Kit Quick Installation Guide 1 2 Features IEEE802 11b g standard e Intended MIMO XR technology can improve wireless coverage up to 450m coverage radius is six times than general 802 11g products Environmental factors may adversely affect wireless signal range e Detachable Antenna Design 3 antennas support TX Burst technology Can effectivly improve transmit speed when working with corega WLCBGMO or corega WLUSB2GO Supports WEP 64 128bit WPA WPA2 PSK WPA WPA2 EAP security setting Internal NAT and NAPT fuction allowing several computers access Internet compatible on line gaming and IM software at the same time e Supports WMM mode improves transmittal quailty of multimedia software e Supports WDS P to MP P to MP bridge mode and AP Repeater repeater
13. Auto obtain IP DACP nunawapumaaaaaaaniaararinbassa 17 NEA 19 4 1 3 Dynamic IP PPPOE aaa aasam mnNG 21 4 2 Establishing Wireless Internet CONNECTtION cecssessecseeseceneeseeees 23 4 2 1 Adjust the ANtenind sssssssssssssssssssssessesscssssessseessessees 23 4 2 2 Setup Wireless Adapter uu ccecsssssssscseesecseesesseeseseesesseess 23 5 Wireless Security CONFIGQUIATION cecsssesssesseessessscssessesssessesssessecsssssssssesstssseesees 27 SINE CNO e Naa 27 BZ WPA ean AA AA AN DN 28 NEON kamara Akma A E E 28 Ne ae cecsecce ceca E seat eee ee estes 29 6 Function IMTOOUCTON aNG 30 Contents aaa NOS daa ANA AA secret necator 30 lt WAN setting internet gt ssessesssessseesesssesseeseesseoseesseossossesseessee 30 KWAN setting Dynamic DNS gt ee ssssssssseseesscsecsecseeseeseeseeseess 33 lt WAN setting Other setting gt s sessssessssssssssssseeeeesesssssssssssssceeeeeee 34 LAN setting LAN IPS a mamaaanamaaa orisii 34 LAN setting DHCP S rVer gt escssssscssssesscsscssesscnsesscsscsecsscucesceseeseess 35 lt LANSettiNnG PCatabase gt ecesssssssssssssesssssssssessssscssssssesseseeseess 35 lt Wireless setting 802 119 b SCttING gt cccssssessesssesseeseesseeseeseee 36 lt Wireless setting 802 11g b security setting 37 lt Wireless setting Access CONtrOl gt sesssseesesssssssecsesssssssseeesrssssssss 37 lt Security SELINA NAA esteem seen 38 lt S
14. BF E7 92 0F 3 Ampon cance Bak 1 Enter the pc name and select PC obtain IP method 2 Configure the MAC address data of PC 3 Click Add PC Data to complete the setting WLBARGMO Manual lt Wireless setting 802 11g b setting gt Wireless Setting 802 11gib Setting ESSID corega Mode au igr Channel 11 TX Burst Enable Hidden AP Disable Ware Diane WID5 Lusabilg Remote AP MAC Cs cancer Lea _ ESSID ESSID is aname that makes wireless adapter identify this Router The default ESSID is corega Mode 802 11b g auto connect in either 802 116 or 802 11g 802 11g connect in 802 11g mode Channel When there is interruption other channels can be selected TX Burst Enable Disable frame burst function When it is checked transmit throughput will be improved Only work with corega WLCBGMO or WLUSB2GO Hidden AP when it s enabled ESSID will not be seen in the network Select Disable Enable to manage function of wireless bandwidth the other AP and set the same ESSID P to MP P to MP bridge mode setup the wireless connection with another AP Router 34 Needs to enter the MAC address of that AP and each connected AP needs to have the same setted channel AP Repeater Repeater Mode When signal is hard to reach the other AP users can set this product in AP repeater mode Need to enter the MAC address of lt Wireless setting 802 11g b security setti
15. C Ho coreg A ERANA Asa SSIES gt SRICA Baal Ris ANTS S iS corega Bx UA FB A AR RE ES Ee Goh NRA Ris Acorega mIRE RASA Bona RE RRB AYE iReees gt SAAR Oe AAAS ai C T TRAE gt coregakeisia la FERR corega K K designs develops and markets professional networking products that address the specific needs of small and medium enterprises and home user s easy to use quality and reliable services of networking solutions requirements Established in 1996 corega 100 founded by Allied Telesis Group in Yokoha ma Japan corega s core products consists of 10 100 1000 Ethernet products Wireless Networking Products 802 11 a b g series broadband access routers Bluetooth series and other networking peripheral such as IP camera and USB Phone Thank you again for purchasing corega s products Wish you would enjoy the powerful and friendly corega connecting experience Appendix 4 we Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential instal lation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference
16. CG WLBARGMO MISO Wireless broadband Router User Manual Contents WLBARGMO Manual 1 Product Introd ct AA 3 1 1 Package CONTENMG csccssssssssssscsssssssesssssssssecsscssessssosssccsecsussessassasescsussnseasenss 3 APA AA AA KA cb aes cece terete tee 3 1 3 Hardware INtroductiOn ccccssssssssssssssssssssssssssssssssssscsessscesssssesesscessenss 4 2 Productinstalati OM asnes R 5 2 1 Hardware InstallatiOn ssssessssssssssoeeesssssssseeeeessnssesseessosnssseseeessossssseeeee 5 2 2 Installation ProcedUre unuci GG GG 5 E a Olea ENa Renee eee AA AA na E ANT 6 3 1 TCP IP CONnPIQUrAatiON ccsesssssssesssssssssesssessessscssscsscssessscsssssecseesesssesseesss 6 3s WINDOWS KPO Sisssiinsnrsiissnncaiscnntasdonnnnddonusminnmnmeadiias 6 3 1 2 Windows 2000 O 5 essessssssssssesscscsssssssessesseesessesscsncescencescescseasees 8 3 1 3 Windows 98 95 ME O 5S c csesssssescsssssssssssssssscssssssessesesseseneeseees 11 3 KAMACOSO INO Daanan 12 3 LIMAGO NO Sana aaa aa 12 3 2 Browser CONPIQUIATION ce ceesessssessessscssessecssecseesesssscsssssessseestesneesees 13 3 2 1 Windows OT ccssssrsnssetesnvtstenctvnsccsniassinsansasvevsernyssietanisetiosatanitvonres 13 Sd AMAG aaa E E E T EA E 14 4 Network CONPIQUIatiON ccessesssessssssesssssscssssssessesssecssssssssssscssessscessssscseessseeseees 15 4 1 Quick Network CONFIGUIAaTION ccsssssssssssessseesessscssesssssstssseeseessceneesseess 15 4 1 1
17. LAN setting LAN IP gt LAN Setting LAN IP MAC address 00 50 18 21 CF 8B LAN IP address 192 168 1 1 Subnet Mask 255 255 255 0 MAC address Displays the MAC address of LAN LAN IP address The device IP address not recommended to change this address Default setting 192 168 1 1 Subnet mask Deafult setting 255 255 255 0 WLBARGMO Manual lt LAN setting DHCP servers LAN setting DHCP Server DHCP Server 1 Enable DHCP start IP 192 168 1 492 1681 50 3 DHCP end IP 1 Select Enable to enable DHCP server function Default is enable 2 Enter DHCP servers start IP and end IP 3 Then click on save button to save the setting lt LAN setting PC database gt the following table display the current connected users information you can add edit delete users data PC database Canaan CU EF PC name IP address i Sa MAC address DHCP Client Operate x MAK EA A IC p ALLIED SANDY 192 168 1 22 LAN 00 50 BF E7 92 0F Autoontain Edit DHCP client Add a pc data click on add to add a new user data LAN setting PC database advanced setting Add Edit Delete PC list f new added pc cant be connected please enter its MAC address 1 PCname IP address Auto obtain DHCP client Manual obtain DHCP client 192 168 1 Connection Type LAN Na MAC address Auto searching connection mode O MAC address 00 50
18. NS Configuration Gateway WINS Configuration P Address An IP address can be automatically assigned to this computer If your network does not automatically assign IP addresses ask your network administrator for an address and then type it in the space below WLBARGMO Manual 4 Click Gateway tab remove all the gateways and press OK to close the window TCP IP Properties 21x Bindings Advanced NetBIOS DNS Configuration Gateway wins Configuration IF ddress The first gateway in the Installed Gateway list will be the default The address order in the list will be the order in which these machines are used New gateway Remove lt Remove all of the gateways 5 Go to Network and press OK to close the page 6 The Restart the windows screen will pop up press OK to restart the PC If the PC is not shown this message restart the PC manually 3 1 4 Mac OS 8 x 9 x O S 1 Open the TCP IP configuration from Control Panel 2 Select Ethernet Network in the connection methods select DHCP server in Configuration and close this page 3 1 5 Mac OS X O S 1 Go System Configuration in Macintosh category 2 Open Network configuration in System Configuration If there is no Network configuration select Display all 3 Select Built in Ethernet in Display from Network window Select Use DHCP in Setting from TCP IP 4 Press Apply
19. Timeout 5 Minute 5 300 Back to default setting Save setting Load setting Language Firmware Update Time Setup Remote Control PING Testing Save Cancel Back Admin login name User name for login this management program Default setting is root Save Setting Click Save to save your setting values as a file Load Setting Click Load to load the files of your setting values that you saved earlier Time Setup Select one of the time setup models If user is in Day light saving region please select enable WLBARGMO Manual Management Time Setup Time Setup Set Date and Time manually v Date 2006 3 1 year Month Day Time 0 0 0 Hour Minute Second Daylight Saving Daylight Saving Disable v Start 1 vis 1 l0 Month Day Hour End 1 vis 1 l o Months Day Hour Firmware update 1 Click Browse to open the data folder Follow the route that the firmware saves to select the file Management Firmware update File location Browse 2 After selection click Firmware update 3 When the countdown starts do not click any button The update will complete soon afterward Upckabng Bremene Fleare dont shut down power while updating Enl have 37 seconds remanung please war Note You may proceed Check for updates to look up the lat
20. WLBARGMO Manual 3 2 Browser Configuration 3 2 1 Windows O S The following examples are for Windows XP O S skip this chapter if you are using Windows 2000 98 ME 1 Open Internet Explorer IE 6 0 select Tools menu and click Internet Options If a Dial up Connection window is pop up close it and do not connect to the Internet now 2 Cannot find server Microsoft Internet Explorer File Edit View Favorites Help Ku Mail and News gt ey i ts x Synchronize K FEREN iE Medi Windows Update Address Ea http fie microso ver 6 amp ar msnhome E Show Related Links 2 The page car AT 2 Click Connections tab 5 select Never dial a connection 5 click LAN Settings Internet Options PJ General Security Privacy Content Connections Programs Advanced To set up an Internet connection click Setup Add Choose Settings if you need to configure a proxy Settings server For a connection CJ Dal whenever a network connection is not present O Always dial my default connection Current Virtual Private Connection Set Default Local Area Network LAN settings LAN Settings do not apply ko dial up connections LAN Settings Choose Settings above For dial up settings WLBARGMO Manual 3 Unselect all three options in the Local Area Network LAN Setting Local Area Network LAN Settings Automatic configuration Automatic configuration
21. ations Applications User Defiralion ky Trigger Incoming ports Remark Special Applications List Max 10 records Status Applic atians Trigger Inecming ports Remark Operate Back lt Advanced setting DMZ gt If the online game s port range is unknown or its parameter is different every login DMZ function is recommended While this function starts select the us ers being allowed to connect with then click Save Advanced Setting DMZ DMZ Server Please select a PC v Note 1 The PC becomes vulnerable to being hacked if DMZ function starts Please only use it in need 2 The PC with DMZ function needs a fixed IP address 3 DMZ function can only be used in one PC lt Avanced setting Routing Table Static Routing gt Add Edit Delete static routing can be set in the table After key in of static routing information click Save The setting log will be displayed afterward Advanced Setting Routing Table Static Routing Destination Subnet Mask Detaut Gataway Save Cancel Statie Routing List Max 8 recordz Destination Subnet Mask Detank Gateway Operate Back lt Advanced setting Routing Table Dynamic Routing RIP gt The table allows dynamic routing setting Select RIP version in the below column this product supports both RIPv1 and RIPv2 then Save to complete the setting Advanced Setting Routing Table Dynamic Routing RIP LAN RIP Transferring Receiving RiPvi WLBARGMO Manua
22. channels 1 through 11 This equipment has been SAR evaluated for use in laptops notebooks with side slot configuration www corega com tw www corega asia com corega Taiwan Inc 7F No 10 Lane 345 YangGuang St Nei Hu Chiu Taipei City 114 Taiwan R O C TEL 886 2 8751 9164 FAX 886 2 8751 9174 PN T30 UM841 1 00 Rev B
23. complete the configuration All the forbidden data will be displayed in the table below Security Setting Filter List Url Address or key words Save Cancel Filter List Max 10 records Status Limited Url Address Operate lt Advanced setting virtual servers Virtual server is an appointed port opened by the PC in connection with the product allowing other users connecting up via WAN Open servers or special online games can take advantage of this function Setting processes are as follows 1 Select a PC to be the virtual server 2 Select Service 3 Enter Port Range of internet connection with the server and Port Range used by the server software 4 Select Protocol 5 Remark column can be filled in with an explanation of the server 6 Click Submit after setting All info will show in the below table Advanced Setting Virtual Server 4 Connecting with ape Please select aPC w 2 Service User Definaton 3 Port Range pa 165535 L Advanced Setting 4 Protocol TCR 5 Remark G Submit Cancet Virtual Server List Maw 20 records LAH WAN Status Connecting with a pc Service Port Port Protocol Remark Action Back lt Advanced setting Special Applications gt Add Edit Delete the setting of special application in the table After key in re lated information please click save and the setting will be displayed in the list WLBARGMO Manual Advanced Setting Special Applic
24. e cable line between the modem and internet been connected correctly 4 Have the cable lines among the modem product and PC been connected correctly gt When the product and modem have been connected correctly WAN LED will light up If no light please remove cable line then re plug in If the modem has a MDI MDI X button please try to switch it gt When the connection between PC and the product is normal the Link Act LED of the front LAN port will light up after the PC s power is turned on 5 Has the connection with ADSL s splitter been linked up correctly There are two kinds of splitter Telephone and ADSL modem 6 Does the PC s network adapter function normally gt Right click on My Computer and select properties gt Device manager gt Display Network adapter If there is a marking of X or it means that the network adapter doesn t perform normally Please re install it 7 Is your network setting correct gt Check if TCP IP setting is correct or not Please refer to 3 1 TCP IP Configuration to check your setting WLBARGMO Manual 8 Has all information provided by your ISP been entered correctly 9 Are the settings of your web browser correct Q2 Can not access the management program A Please confirm the following settings 1 ls the TCP IP address correct Please refer to 3 1 2 Is the cardbus successfully installed Right click my computer select properties gt click d
25. ecurity setting Connection COntrol gt sssssssssesssssssseeesssssssses 38 cSecurity setting filter LISTS esceessssssssesssessesscssssssesseeseesseesesses 39 Advanced setting virtual Serv f gt ssssssssssssssssssscsesssssssseersessssssss 39 lt Advanced setting Special ApplicationS gt sssssssssecesssssssse 39 lt Advanced SettiNG DMZ gt ccscsessssssesssessssssssesssssessseseseesssessesees 40 lt Avanced setting Routing Table Static Routing 5 40 lt Advancedsetting Routing Table DynamicRouting RIP 5 40 lt Advancedsetting Routing Table Routing Tables 41 lt Advanced SettING UPNP gt c csessssssssssssssssssessssssssecsssssessscsscseceseesens 41 Advanced setting SNMP gt cssssssssssssssssssssssssssecsssssssssesscsecsseeseens 41 SIVAN CS VMI AA deuateesapstute 42 KOI AA AA AA 44 lt Status Log Display DOSAttacklOg gt sessssssessesssessesesesseeseens 44 lt Status Log Display system lOG gt csssssssssssessssecssessssseesssesssesseess 45 lt Status Log Display E mail fUNCtION gt ee essssseesseecseeseeesees 45 ALA AA AP NO NAA 46 Product Introduction WLBARGMO Manual Corega WLBARGMO is a MISO wireless broadband Router with IEEE802 11g wireless access point standard Its MIMO XR technique can improve transmit speed and coverage area The maximum transmit length is up to 450m and the coverage area can be six times more than general
26. efresh lt Status Log Display Dos Attack log gt Dos attack log is displayed in a table Statua i Log Dieplay DoS Attack Lag WAM Type Flood IP War 1 00 Display time Wed Mar 0i 00 58 45 3006 WLBARGMO Manual lt Status Log Display system log gt System log is displayed in the table Status Log Display System Log WAN Type Fixed IP Ver 1 00 Display time Wed Mar 01 00 59 11 2006 Wed Mar 01 00 53 43 2006 DOD is disabled e Wed Mar 01 0053 45 2006 DOO is disabled Wed Mar 01 00 53 45 2006 DOD is disabled Wes Mar 01 0053 45 2006 DOO is disabled Wed Mar 01 D0 83 45 2006 DOO ts disabled Wed Mar 01 00 53 45 2006 DOD is disabled Wed Mar 01 NO 53 45 2006 DOD is disabled Wes Mar 01 00 53 45 2006 DOO is disabied Wed Mar 01 00 53 45 2006 DOD is disabled Wed Mar 01 00 83 46 2006 DOO ts disabled Wed Mar 01 00 53 46 2006 DOO is disabled Wed Mar D1 00 53 48 2006 DOD is disabled Wed Mar 01 00 59 49 2006 DOO is disabled Wed Mar 01 00 53 51 2006 DOD is disabled Wed Mar 01 00 53 51 7006 DOO ts disabled Wed Mar 01 00 53 51 2006 DOD is disabled Wed Mar 01 005351 2006 DOO is disabled Wed Mar 01 00 53 51 2006 DOO is dtsables Wed Mar 01 00 53 51 2006 DOD is disabled Wed Mar D1 0053 51 2006 DOO is disabled lt Status Log Display E mail function An E mail address can be set below Special incidents will be recorded and sent to the appointed E mail address After entering all information click Save to save and complete the setting
27. emove The following three settings are applied to all connections with TCP IP enabled For resolution of unqualified names Append primary and connection specific DNS suffixes IV Append parent suffixes of the primary DNS suffix Append these DNS suffixes in order 3 Add Edit Remove DNS suffix for this connection I Register this connection s addresses in DNS Use this connections D Please do not WLBARGMO Manual 3 1 3 Windows 98 95 ME O S The configurations in all Windows 98 95 ME are the same and this manual takes Windows 98 as an example 1 Enter Control Panel and double click Network 2 Click Configuration tab and select TCP IP click Properties Network Ux Configuration Identification Access Control The following network components are installed Client for Microsoft Networks Microsoft Family Logon Dial Up Adapter 8 Intel R PRO 100 VE Network Connection 3 TCP IP gt Dial Up Adapter Y TCP IP gt Intel R PRO 100 YE Network Connection Add Remove Properties Primary Network Logon Microsoft Family Logon File and Print Sharing r Description TCP IP is the protocol you use to connect to the Internet and wide area networks OK Cancel 3 Select IP Address and select Obtain IP address automatically Press OK TCP IP Properties 7 x Bindings Advanced NetBIOS D
28. est firmware from corega s web page Remote control The setting allows accessing the management program via remote control Management Remote Control Remote Central 1 Disable Port 2 1 3600 3 Save Cancel Gack WLBARGMO Manual The activation processes are as follows 1 Select Enable 2 Indicate 1 9600 for parameters of port range e g 8080 Recommended keeping default values 3 Click on Save after completing settings e g Assume the port value is 8080 enter IP address as the type http XXX XXX XXX XXX 8080 to access the management program by remote control PING testing Enter the IP address into the Target IP Address box then click on Ping It will display the ping testing result Targat IP Address lt Status gt Management PING Testing Back Connection status log is displayed in the table Firmware Version Status Ver 1 00 Orerating Time 58 Minute 27 Second MAC adcress 00 50 18 21 CF 88 Sudret Mask 255 255 255 0 n I Add ess 19216011 pra O LAN Bitin CHC Enable CRC start iP 192 168 1 21 CHC end iP 19 168 150 MAC accress 00 50 16 21 CF 88 Mace 11b g Enable Wireless Status Security Open System Disable Charnel t1 ESSIC corega Suns Wireless access Enable MAC azcress 00 S0 18 21 CF 84 WAN Fed P I Addre35 0000 Wal Status Susret Wask 0000 CefauW Gateway 0000 CNS Saruvar 0000 CNS Saway 2 0000 R
29. evice manager if a x appears symbol on the network adapter icon please re install the product 3 Make sure the Proxy server box is unchecked refer to chapter 4 Q3 Not able to log in the management program A You have 4 ways to check and solve the problem 1 Close and re open the IE browser and login the program again 2 Log out and re login the Windows OS Then login the program again 3 Probably the management program is accessed from the other user Wait until that user exits the program 4 Reset to default settings Refer to Q9 for more details and re login the program Q4 Forget the password A If you ever changed the password of the management program please enter the one you set If you forget the password please reset to default settings Please refer to Q9 for more details Q5 How to set or change the password of the management program A Access the management program and then click Management Enter new password in the columns of Admin login passowrd and password confirmation then click Save When you re access the management program you must enter new username and password The default username is root and no password Q6 Failure in firmware update A If the firmware update fails please contact us by Online Customer Support webpage Please go to the website of http www corega asia com gt click on Support and right click the Online Customer Support item gt Filling the
30. guage English v Region Singapore Apply WLBARGMO Manual 5 Click Quick Installation Setting ad OLR WAN Sating gond wide wab DE LAN Sinig E Wireless Setting DE Stiu Setting EHE Advanced Seting ag Managamant Mig Sts 6 When seeing this screen shot click on Next Setup Wizard Setup wizard will ep you bo configure your network Please hayo Wi the networking documents ready PIESS make Sure the Device is connected with modem click on Next 7 Select your connection type Please make sure that your ADSL connection type is correct as you enter the correct information can be obtained from the documents given by your ISP If not consult with your ISP before setting Setup Wizard Network Connection WAN setting Please configure network connection WAN setting Please select your connection type Auto obtain IP DHCP e g Cable Modem O Fixed IP Float IP PPPoE WLBARGMO Manual 4 1 1 Auto obtain IP DHCP 1 If you are subscribing to auto obtain IP service or DHCP Dynamic IP from your ISP such as Cable Modem that obtain an IP automatically for connection please select Auto obtain IP DHCP Click on Next Setup Wizard Network Connection WAN setting Please configure network connection WAN setting Please select your connection type Auto obtain IP DHCP e g Cable Modem Fixed IP Float IP PPPoE 2 Press MAC address clone to
31. in order of use Add Edit Remove The following three settings are applied to all connections with TCP IP enabled For resolution of unqualified names Append primary and connection specific DNS suffixes Append parent suffixes of the primary DNS suffix Append these DNS suffixes in order Se Add Edit Remove DNS suffix for this connection _ Register this connection s addresses in DNS amp Please do not Jse this connecton s DNS suthix m DNS registration check this box 6 Go back to Internet Protocol TCP IP and press OK 7 Press OK to close Local Area Connection Properties 3 1 2 Windows 2000 O S 1 Go to My Computer and enter Control Panel click open Network and Dial Up Connections elo Gf search Pader gta GS ara EB Address Control Pana is S F5 amp aaa Magee Control Panel Option Mandan poe rams Canned li other congue Pai Printers Begoral metab and the niema bii taya options arn a gt 4 iras Hali opt m ener oe heed fou ink al pilar Caress Tasks Mikire WLBARGMO Manual 2 Right click Local Area Connection and select Properties CH a A Make New ANG Connection Disable Statis Create Shortcut Delete Rename Note Please check if TCP IP had been installed in the Local Area Connection 3 Click Internet protocol TCP IP and click Properties Local Area Connection Pr
32. ing all installation data and or equipment Install the hardware gt PC setting gt Open the browser such as IE 6 0 and type 192 168 1 1 in the browser s address bar and press enter gt User name Root leave Password empty and press Submit gt Select Quick Installation Setting for quick installation gt Setting the Wirless Security gt Use PC with compatible wireless card for wireless connection PC Setting 3 1 TCP IP Configuration The following steps and screenshots maybe dissimilar in different operat ing systems This manual takes Windows XP 2000 95 98 ME and Mac O S as examples 3 1 1 Windows XP O S 1 Enter Control Panel 5 click Network Connection 5 right click and select Open Help Search Key Folders fii G6 X D G6 PY A DW Accessibility Add Hardware Add or Administrative Date and Time Display Folder Options Options Remov Tools A a O Y eri B Intel R Internet Keyboard Mouse r Options Extre Options a A Cc ft Create Shortcut Yo g Scheduled SoundM4x Sounds and Speech gs Taskbar and User Accounts Tasks Audio Devices Start Menu 2 Click Local Area Connection and right click and select Properties eB LZ L dhe Make New Local Area Connection Connection Ceman m Local Area Disable Status Create Shortcut Delete Rename WLBARGMO Manual 3 Click General 5 click Internet Protocol TCP IP and click Pro
33. int mode Note When switch to AP mode the product will stop sending IP the WAN port will not be function The LAN port will also turn to general Hub function Therefore we suggest user to use the default setting Wireless Enable enable the wireless function Wireless Disable disable the wireless function Wireless Function lt WAN setting internet gt The internet setting can be configured according to your internet connection type Link connection speed default setting is recommended WLBARGMO Manual A For PPPoE WAN setting Connection Mode Wan Speed auto w PPPoE O Auto obtain IP DHCP Fixed IP PPPoE Session Setting Connection Status Disconnected MAC address 00 50 18 21 CF 8A Username l Password Password Confirm Service name Ni Optional Connection type j Manual Setup I paaa Idle Timeout 10 minute 0 60 Authentication auto w MTU value 1454 bytes 576 1492 DNS Server Auto Setup Manaul Setup DNS Server 1 0 01 DNS Server 2 0 0 0 0 Save Cancel Please enter username given by your ISP Please enter password given by your ISP Confirm Please type your password again password Connection Auto Reconnect always on line recommended type On Demand connect when accessing to Internet manual connection manually connecting to internet Authentication Maximum Transmission Uni
34. l lt Advanced setting Routing Table Routing Tables All routing logs are displayed in the table Advanced Setting Routing Table Routing Table Connecting with a pe Subnet Mask Default Gateway 192 168 1 0 255 255 255 0 192 168 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 lt Advanced setting UPnP gt Activating this function can detect the device or software of LAN supporting UPnP For example online games supporting UPnP or Windows Messenger Ver 4 7 or above MSN Messenger Ver 5 0 or above and so forth Set its status usable The default value is Enable Advanced Setting UPnP Use UPnP Enable Rj lt Advanced setting SNMP gt There are two ways of SNMP Syslog UDP and SMTP TCP 1 Start SNMP User can select two ways to start SNMP function If select Local the product will respond from LAN If select Remote the product will resoond from WAN 2 Get Community this box is in response to the setting of Get group of GetRequest 3 Set Community this box is in response to the setting of Set group of SetRequest 4 WAN assign IP address Enter the IP access the product from WAN Advanced Setting SNMP SNMP Local Get Community public Set Community private WAN assign IP address 0 0 0 0 WLBARGMO Manual lt Management gt Management Admin login name root i Admin login password Password confirmation Connection
35. may override manual settings To ensure the use of manual settings disable automatic configuration Automatically detect settings se automatic configuration script bddress g ae kan m Proky server se a proxy server for your LAN These settings will not apply to dial up or YPN connections 4 Press OK in the Internet Options 3 2 2 Mac O S 1 Open Internet Explorer IE 5 0 Go to Edit in the menu bar select Internet Explorer Preferences 2 Select Proxies options in Network on the left side configuration items 3 Do not select Web Proxy press OK Internet Explorer Preferences If you are accessing the Internet from a private network you can set gateways to allow Internet access Contact your network manager Browser Display for more information Note These settings are shared with other Web Content applications through Internet Config Language Fonts Use Proxy Servers Subscriptions 7 Web Proxy f Settings 3 Java amp Use Web Proxy for all Interface Extras i Bypass Web Proxy for FTP Security F Secure Proxy F Settings gt Security Zones s Mail Proxy Settings 3 Q Ratings puna sa Advanced Gopher Proxy f Settings gt Y Forms Autofill List the sites you want to connect to directly bypassing the proxies Forms AutoComplete set above Put a space or comma between each site AutoFill Profile wW Receiving Files
36. mode e Advanced SPI DoS Firewall e Chinese and English version utility e Supports UPnP and on line broadband applications Such as Windows Messenger MSN Messenger Yahoo Mesenger Skype ICQ and etc WLBARGMO Manual 1 3 Hardware Introduction 0909 1 Initial Button Press this button it will reset to default setting 2 WLAN LED Green ON Connected 3 Power LED Green Indicate power status 4 Status LED Red Blink Working normal ON Firmware upgrade 5 WAN LED Green ON Connected Blink Transmitting or receiving data 6 Speed LED Green ON 100Mbps Off 10Mbps 7 Link LED Green ON Connected Blink Transmitting or receiving data 8 Detachable Antenna Connector 9 WAN port Connected with modem 10 LAN ports 1 4 Connected with PC 11 ACIN Socket Connect with power adapter Product Installation WLBARGMO Manual 2 1 Hardware Installation Following the steps below to set up WLBARGMO and the connection 1 Insert the cable connector into the Network Adapter embeded in PC and insert the other side into one of LAN ports 1 4 of the Router 2 Insert the connect into the WAN port of the Router and insert the other side into the modem 3 Connect the Power Adapter and plug in the AC power lt ADSL gt WLBARGMO Modem 2 2 Installation Procedure To ensure successful installation following the below steps after confirm
37. networking corega testing She Change the order of preferred networks FF Security enabled wireless network G Change advanced LANKom Electronics Co Ltd settings Unsecured wireless network ATTW OFFICE H Security enabled wireless network WPA MPMR Unsecured wireless network WLBARGMO Manual 3 Connection status will appear in the bottom right of the screen Wireless Network Connection corega Speed 54 0 Mbps Signal Strength Good Status Acquiring network address Note The wireless connection has been established now Please go to corega s website at http www corega asia com to check the connection to the Internet Wireless Security Configuration WLBARGMO Manual To prevent from unlawful access to your network you are recommended to perform wireless security setting Type 192 168 1 1 in the browser s address bar press Enter Enter the function menu ad click on 802 1 1g b Security set ting item And select WEP or WPA setting amp NN Wireless Setting DJ 802 11 g b Setting GG 80211 94b Security setting Connection control 5 1 WEP Setting In order to prevent your information from being hacked it is recommended to use WEP encryption when using wireless connection Wireless Se ing BZ 1gb Security Setting Authente ation 1 wer Cipher Type 2 m Encryption 3 ant Auto generate WEP a Genecate Key ces WEP KEY 16 CecimalnG SY af Jj ten G KEV
38. ng gt WLBARGMO Manual This section contains WEP WAP PSK WPA2 PSK WPA EAP and WPA2 EAP encryption setting please refer to Chapter 5 to get detail information Wivelens Setting BGP 11g Security Setting Aumastieanen ho Emcrypion O m Gipher Tyee Dianie Enerypiics Auto Generate WEF WEP HEY 16 derimaiaji 0 a f HEYA RETZ KEYS oT J 1 37 Sme Cee Hk Wireless setting Access control gt Wireless Setting Connection Control Wireless to wireless connection Enable v Wireless to wire connection Enable w MAC address filter list Disable Only allow authorised client to access To configure authorised clients please edit add from client database ID Enable PC name IP address MAC address DHCP Client Wireless to wireless connection Wireless to wire connection MAC address filter list Configure wireless communication between clients Enable Disable enable or disable wireless communication between clients Configure wireless and wired communication between clients Enable Disable enable or disable communication between wireless and wired client Use MAC address filter to control network communication Enable only users on the list can access the network Disable all users can access the network E a U OO a N WLBARGMO Manual lt Security setting gt Configuring firewall and no response to WAN Ping requests Security Setting
39. ng that repeat these setps in the section 4 1 3 Dynamic IP PPPoE 1 If you are subscribing dynamic IP connection or known as PPPoE from your ISP you need to obtain a set of username and password from your ISP and acquire a IP address each time your connect to the Internet select PPPoE and then Next Setup Wizard Network Connection WAN setting Please configure network connection WAN setting Please select your connection type Auto obtain IP DHCP e g Cable Modem Fixed IP Float IP PPPoE 2 Enter the username and password provided by your ISP and click on Next Please configure your network from infomation provided by your ISP Please enter your password and username which are given by your ISP Username Password Password Confirmation Service name Optional SS BU WLBARGMO Manual 3 Click on Save to perform connection tests Save please click on save Test result Prepare for network testing Please wait 7 seconds 4 Within seconds the result of the connection test will be appeared in the dialogue box to indicate the connection status When Connection OK appears click on Close Setup Wizard Setup complete Save please click on save Test result Prepare for testing Please wait 0 second PPPoE IP address 11 15 1 14 Subnet mask 255 255 2550 Default gateway 10 15 1 254 DNS server
40. operties ajx General Connect using BY Intel R PRO 100 YE Network Connection i Configure Components checked are used by this connection Client for Microsoft Networks EU File and Printer Sharing tor Microsoft Networks Y Internet Protocol TCPYIP Install Uninstall Properties Description Transmission Control ProtocolAntemet Protocol The default Wide area network protocol that provides communication across diverse interconnected networks f4 Show icon in taskbar when connected WLBARGMO Manual 4 Select Obtain an IP address automatically and Obtain DNS server address automatically And click Advance Internet Protocol TCP IP Properties a 2 xi General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically C Use the following IP address P address Subnet mask Default gateway Obtain DNS server address automatically C Use the following DNS server addresses Preferred DNS server R i Altemate DNS serwer 5 Click DNS tab in Advance TCP IP setting page and unselect Register this connection s DNS address and press OK Adyanced TCP IP Settings IP Settings DNS wins Options DNS server addresses in order of use 5 2 Add Edit R
41. p Manaul Setup DNS Server 1 0 0 0 0 DNS Server 2 0 0 0 0 WAN IP address Subnet mask Default gateway Please refer to your ISP internet service information Maximum Transmission Unit Deafault setting 1500 Byte DNS server When Manual Connection is enable two DNS server addresses can be inserted DNS1 and DNS2 Multi NAT Setup corresponding sets of external IP and public IP lt WAN setting Dynamic DNS gt Dynamic DNS is a connection of LAN s virtual server through URL internet access or called dynamic IP No fixed IP address that also can connect through URL internet ac cess WAN setting Dynamic CHS Virtual server deviess can be connected through URL internet acess Dynamie DNS 1 Glsabie DONE Provider DmDN5 0rg Tymamic Lagin nama 3 Login password 4 Domain nama 5 6l sae Cancel Bak WLBARGMO Manual 1 2 3 select enable dynamic DNS services Select one DDNS Provider enter login name enter login password Domain name Click Save Note Corega does not provide DDNS service Please register on one DDNS provider web site before you setup this function 4 5 6 SA th hd lt WAN setting Other setting gt WAN setting Other setting VPN PPTP Pass Through VPN IPSec Pass Through Enable VPN PPTP pass through VPN pass through function enable disable VPN IPSec pass through VPN pass through function enable disable lt
42. perties 4 Local Area Connection 2 Properties PR General Authentication Advanced Connect using E9 Intel R PRO 100 VE Network Connection This connection uses the following items E Client for Microsoft Networks A File and Printer Sharing for Microsoft Networks 2 QoS Packet Scheduler Internet Protocol TCP IP Uninstall Properties Description Transmission Control Protocol nternet Protocol The default wide area network protocol that provides communication across diverse interconnected networks Show icon in notification area when connected 4 Click General select Obtain an IP Address Automatically and Obtain DNS Server address automatically and press Advance Internet Protocol TCP IP Properties General Alternate Configuration You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP addres S ubnet mast Default gateway Obtain DNS server address automatically Use the following DNS server addresses WLBARGMO Manual 5 Click DNS tab unselect Register this connection s address in DNS and press OK Advanced TCP IP Settings IP Settings DNS WINS Options DNS server addresses
43. s Specifications WLBARGMO Manual Compliance Standard WLAN IEEE802 11 IEEE802 1 1b IEEE802 11g LAN IEEE802 3 IEEE802 3u IEEE802 3x Interface WAN 10 100Mbps x 1 Port RJ 45 Auto MDI MDI X LAN 10 100Mbps x 4 Ports RJ 45 Auto MDI MDI X Frequency Band 2 412 2 472 GHz Transmission speed IEEE802 11b 11 5 5 2 1Mbps IEEE802 1 19 54 48 36 24 18 12 9 6Mbps Transmission Power 20dBm 1 1b 16dBm 11g Coverage Area Indoor 150m Outdoor 450m MIMO XR Function Enable Range Environmental factors may adversely affect wireless signal range Transmission method DS SS OFDM BPSK QPSK CCK Protocol CSMA CD Security ESSID WEP 64 1 28bit WPA PSK WPA2 PSK WPA WPA2 PSK WPA EAP WPA2 EAP WPA WPA2 EAP TKIP AES Antenna Type Detachable Antenna SMA Connector Antenna Gain 2dBi Power Specifications Power Requirement AC 12V 5 Power Current 0 48A Power Consumption 6W Environment Requirements Operating Temperature 0 40 C Humidity 29096 non condensing Storage Temperature 20 60 C Humidity lt 95 non condensing Physical Specifications Support OS Windows98 SE 2000 SP4 ME XP SP1 SP2 Case Material Plastic Dimension 28 5 W x 120 D x 165 H mm Weight 285g bo Aboutcorega ag corega corega 7 mI 1 996TERVIT TRA ASTI gt BIER S ITI CAAA arson DIO ASS FRR EEA All ae KUA HF RIE DARE ES 8 kA NYE oo BRASS e coreg BeeT gt FABER amp co Abe mh gt IA 20027 2AKRGItMIL MER FH ERE ESE S SAA RAABHESE
44. sponding wireless network adapter 2 Select Cipher Type Recommended to keep the default Note The wireless network adapter is required to have the same setting otherwise the connection will fail 3 After selecting WPA shared key key in the Pre Shared Key in connection with the communication device in the below column Please enter 8 63 alphabets or numbers Note The password of the device in connection with the product must be the same otherwise the connection doesn t work out Wireless Setting 802 11 g b Security Setting 1 Authentication WPA WPA2 PSK 2 Encryption Auto generate WEP WEP KEY KEY KEY2 KEYI KEY4 WPA shared key ASCII key 8 63 characters O 16 decimals 64 characters H OTIM 3 1 5 Radius Server Save Cancel Back 5 Cancel 4 Recommended to keep default value of DTIM 5 Press Save to save setting WLBARGMO Manual lt WPA EAP gt 1 Select WPA2 EAP or WPA WPA2 EAP Recommended in the column of Authentication a WPA2 EAP The 2nd generation encryption skill performs stricter protec tion than before Before selection please check the function availability of your network adapter or select b b WPA WPA2 EAP If selected encryption type will be defined automati cally according to the corresponding wireless network adapter 2 Select Cipher Type Recommended to keep the default Note The wireless network adapter is required to have the
45. t when Auto Reconnect is and MTU value disable MTU can be edited Default setting 1454 Byte DNS Server Select Auto Setting or Manual Setting to configure DNS1 and DNS2 servers WLBARGMO Manual B For auto obtain IP DHCP WAN setting Connection Mode Wan Speed Auto O PPPoE Auto obtain IP DHCP Fixed IP Auto obtain IP DHCP fixed IP MAC address jil 00 50 18 21 CF 8A wa Auto obtain IP DHCP O Fixed IP 00 50 18 21 CF 8A Host name MTU value 1500 bytes 576 1500 DNS Server auto Setup O Manaul Setup DNS Server 1 foo DNS Server 2 Type Press MAC address clone to obtain the Ethernet card s MAC address Host name Please refer to your ISP internet service information add edit Host name MTU value Maximum Transmission Unit deafault setting 1500 Byte Multi NAT Setup corresponding sets of internal IP and public IP WLBARGMO Manual C For fixed IP WAN setting Connection Mode Wan Speed Auto v O PPPoE Auto obtain IP DHCP Fixed IP Auto obtain IP DHCP fixed IP MAC address 00 50 18 21 CF 8A PE l O Auto obtain IP DHCP Fixed IP o WAN IP address 10 15 1 41 mpa Subnet mask 255 255 255 0 Default gateway 10 15 1 254 Host name MTU value 1500 bytes 576 1500 DNS Server Auto Setu
46. will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the folowing two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equip ment IMPORTANT NOTE FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an un controlled environment End users must follow the specific operating instructions for satisfying RF exposure compliance This transmitter must not be co located or operating in conjunction with any other antenna or transmitter IEEE 802 11b or 802 11g operation of this product in the U S A is firmware limited to
Download Pdf Manuals
Related Search