Allied Telesis AT-MC601 User's Manual
Contents
1. Figure 3 Rear Panels Hardware Features VDSL Line Port AT MC601 AT MC602 Installation and User s Guide The following sections describe these hardware features of the AT MC601 and AT MC602 network extenders Q U O D D OU O VDSL Line port Q PSTN port 10 100 Mbps twisted pair Ethernet port Status LEDs Management port Management cable DC power supply input port External AC DC power adapter The VDSL Line port allows you to connect the AT MC601 Subscriber unit to a telephone jack wall outlet and the AT MC602 Provider unit to the inside phone line at the wiring closet The two units need to be within 1 200 meters of each other in order for the port to operate properly The port transmits voice data at a frequency of 300 3400Hz and Ethernet data at frequencies of 300 KHz to 8 MHz This port features an RJ 11 connector Table 1 lists the RJ 11 port pinouts and their assignments Table 1 VDSL RJ 11 Port Pinouts Pin Assignment pass through 6 pass through 5 VDSL and phone ring VDSL and phone tip pass through 2 Nim BR D pass through 1 Product Description PSTN Port 10 100 Mbps Twisted Pair Ethernet Port The PSTN port allows you to connect the AT MC601 Subscriber unit to a telephone and the AT MC602 Provider unit to the outside telco box This port features an RJ 11 connector Table 2 lists the RJ 11 port pinouts and their assignments2. A lesser QAM constellation causing reduced line rates If the full constellation rate cannot be achieved because the received SNR is too low then a reduced constellation link can be established and the software can automatically configure the Subscriber unit parameters TC Synchronized Transmission convergence is synchronized Ethernet Encapsulation Sync The process of encapsulating packets into frames at the VDSL link level is synchronized Remote I F Synchronized Remote interface is synchronized Signal Detected The VDSL signal is being detected by the software Link Fail Counter Number of unsuccessful link attempts Micro Interruption Occurred A micro interruption occurred AGC Converged Automatic gain control has converged on the VDSL link Timing Converged The timing acquisition function is converged This only occurs on the Subscriber remote unit ADC Saturation Analog to digital converter has been overloaded with interference Local Remote Select Local to view the parameters for the Provider unit Select Remote to view the parameters for the Subscriber unit The Remote option will only be available when an active link has been established 42 Configuration Ethernet Status To view the Ethernet Status screen click on the Ethernet Status tab at the top of the menu The Ethernet Status screen is displayed in Figure 29 AT MC60x Configurator link DOWN Figure 29 Ethernet Status The parameters on
3. RJ 45 Port Pinouts Figure 4 illustrates the pin assignments of an RJ 45 connector and port Figure 4 RJ 45 Connector and Port Pin Assignments Table 3 lists the RJ 45 10Base T 100Base TX connector pins and their signals when the port is operating in either MDI or MDI X configuration Table 3 RJ 45 Port Pinouts Pin MDI Signal MDI X Signal 1 TX RX 2 TX RX 3 RX TX 6 RX TX Product Description Status LEDs The AT MC601 and AT MC602 network extenders feature the status LEDs defined in Table 4 Table 4 Status LEDs LED Color Description PWR Green Power is applied to the unit 10 100Base TX Port LINK Green A link has been established on the port ACT Green Data is being received on the ports LINE Port ERR Green An error has been detected on the port LINK Green A link has been established on the port MGMT Port The management port features a 8 pin DIN connector for connecting the network extenders to your laptop or PC compatible computer for configuration using the provided management cable Management The management cable included with the AT MC602 Provider unit Cable features a 9 pin RS 232 connector to attach to your computer and an 8 pin DIN connector to attach to the network extender Na 8 pin DIN connector 9 pin RS 232 SS connector Figure 5 Management Cable DC Power Supply Input Port Exter
4. Table 2 PSTN RJ 11 Port Pinout Pin Assignment 1 pass through 1 6 2 pass through 2 5 3 phone ring 4 phone tip 5 pass through 5 2 6 pass through 6 1 The AT MC601 and AT MC602 network extenders each have one twisted pair Ethernet port The twisted pair ports feature RJ 45 connectors with a maximum operating distance of 100 meters 328 feet For the port pinout details refer to RJ 45 Port Pinouts on page 14 Type of Cabling The 10 100Base TX twisted pair port on the AT MC601 and AT MC602 network extenders are designed to operate with Category 3 or better unshielded twisted pair cables For 10 Mbps operation on the twisted pair ports Category 3 or better 100 ohm unshielded twisted pair cabling is required For 100 Mbps operation on the twisted pair ports Category 5 and Enhanced Category 5 5E 100 ohm unshielded twisted pair cabling is recommended Auto MDI MDI X An RJ 45 twisted pair port on a 10 100 Mbps Ethernet network device can have one of two possible wiring configurations MDI or MDI X The RJ 45 port on a PC router or bridge 1s typically wired as MDI while the twisted pair port on a switch or hub is usually MDI X The AT MC601 and AT MC602 network extenders feature automatic MDI MDI X Each port automatically determines the configuration of the port on the device to which it is connected and then configures itself appropriately For example if a port on a network extender is connec
5. AT MC601 AT MC602 Installation and User s Guide Eisen Dit product voldoet aan de volgende eisen amp 1 RFI Emissie EN55022 Klasse A FCC Part 15 Klasse A amp 2 Immuniteit EN55024 amp 3 Electrische Veiligheid EN60950 UL60950 FCC Part 68 Veiligheid ss 4 Gebruik alleen de power adapter die meegeleverd is met de verlenger De AT MC602 kan als stand alone gebruikt worden maar kan ook geplaatst worden in de AT MCR12 chassis In het laatste geval heeft de AT MC602 zijn powersupply niet nodig es 5 Waarschuwing Het toestel wordt uitgeschakeld door de stroomkabel te ontkoppelen Om het toestel stroomloos te maken de stroomkabel ontkoppelen 6 Gevaar Voor Blikseminslag Gevaar NIET aan toestellen of KABELS WERKEN bij BLIKSEM amp 7 N Ventilatiegaten niet blokkeren 8 A Sluit geen telefoonlijn aan op de signaalverbinding 9 Bedrijfstemperatuur De omgevingstemperatuur voor dit produkt mag niet meer bedragen dan 40 graden Celsius a 10 Alle Landen het toestel installeren overeenkomstig de lokale en nationale elektrische voorschriften 58 Translated Electrical Safety and Emission Information Normes ce produit est conforme aux normes de suivantes orl Eemission d interf rences EN55022 Class A FCC Part 15 Class A radio lectriques amp 2 Immunit EN55024 amp 3 S curit lectrique EN60950 UL60950 FCC Part 68 S curit 4 A Utiliser uniquement l adapteur aleatoire fourni avec l extender Le AT MC602
6. DOWN or link UP in brackets The AT MC60x Configurator menu has three screens Configuration VDSL Status and Ethernet Status The parameters on these screens are described below Use the tabs at the top of the menu to toggle between these screens When you have finished viewing or adjusting the parameters on the menu screens click the Close button on the bottom right of the menu to exit from the configuration software The Configuration screen displayed in Figure 26 is shown first by default i AT MC60x Configurator link DOWN Configuration VDSL Status Ethemet Status r Upstream Downstream Actual Mbps 11 26 Actual Mbps 11 26 Min Mbps 0 94 Min Mbps 0 94 v Max Mbps 0 94 v Max Mbps 0 94 Select speed to set Status About Low gt HIGH y Close Figure 26 Configuration 38 Configuration The parameters on the Configuration screen are described below Upstream Downstream The upstream and downstream data transfer rate Actual Mbps Displays the actual data transfer rate on the line The software automatically detects this speed C Min Mbps Allows you to adapt the data transfer rate by setting a minimum speed Q Max Mbps Allows you to adapt the data transfer rate by setting a maximum speed The maximum and minimum speeds in Mbps available in the pull down menus are 0 94 1 06 1 41 1 88 2 11 2 81 3 15 Statu
7. Eme Port ui oen ae A Ie cae e een Ae iaia Res mus mesi SEN STANE 12 SH RRE 13 10 100 Mbps Twisted Pair Ethernet Port 13 Status DA a DEEP 15 MGMT Ports EE 15 Management Cable 5 oii rm the eee A ete EE P RE 15 DC Power Supply Input Port RESET da 16 External AC DC Power Adapter bero rere n RP rer e pe D HEP D rate 16 Software Features sns Ceo Rie ere PEU teren d be t oss pee SIR EE Eb Sl ain cus Do bende TRE 17 Chapter 2 Installation 2 Gea ne POOR loa 18 Installation Safety Precautions piani 2 20 Ee Seege beine rn 19 Additional Compliance Warning Statements i 20 Selecting a Site for the Network Extender i 21 Cables Not Incl ded n egit pO POUR OR ORO sa pt rege ser 22 Unpacking the Network Extender mutilado RR Sead ie een da 23 Installing the AT MC601 Subscriber Unit ue Ra Ra 0880008880 ss eire ira 24 Using the Subscriber Unit on a Desktop 24 Wall Mounting the Subscriber Unit ran EEr eer E 24 Contents Cabling the Subscriber Unit anna aed eke estes ei aetna es 26 Poweting On the Subscriber Unit on sns iaia aaa dune 27 Installing the AT MC602 Provider Unit nono nenne tnmen rennen eene et es RR rra aa naa a naa aa ennen ennen 28 Using the Provider Unit on a Desktop climalit ib ica 28 Wall Mounting the Provider Un 29 Grounding the Provider Unit indi te i e iere nie de eei 30 Rack Mounting the Provider Unit e 31 Cabling the Provider Ult iaia
8. national electric codes amp 10 AT MC601 AT MC602 Installation and User s Guide Additional Additional telecommunication related compliance warning statements Compliance used with the AT MC601 and AT MC602 Extended Ethernet units are listed below Warning Statements Warning When using your telephone equipment basic safety precautions should always be followed to reduce the risk of fire electronic shock and injury to persons including the following 1 Do not use this product near water for example near a bathtub washbowl kitchen sink or laundry tub in a wet basement or near a swimming pool 2 Avoid using a telephone other than a cordless type during an electrical storm There may be remote risk of electric shock from lightning 3 Do not use the telephone to report a gas leak in the vicinity of the leak Caution To reduce the risk of fire use only No 26 AWG or larger telecommunication line cord Caution Mechanical Mounting The attached rackmounting ears must be used to securely mount the device onto the rack 20 Installation Selecting a Site for the Network Extender Observe the following requirements when choosing a site for your network extender a D D D O If you plan to install the AT MCR 12 in an equipment rack check to be sure that the rack is safely secured and that it will not tip over Devices in a rack should be installed starting at the bottom with the heavier devices nea
9. 55022 ClassA FCC Part15 ClassA amp 1 Immunity EN55024 Electrical Safety EN60950 UL60950 FCC Part68 amp 3 Important Appendix C contains translated safety statements for installing this equipment When you see the 47 go to Appendix C for the translated safety statement in your language Wichtig Anhang C enth lt bersetzte Sicherheitshinweise f r die Installation dieses Ger ts Wenn Sie amp sehen schlagen Sie in Anhang C den bersetzten Sicherheitshinweis in Ihrer Sprache nach Vigtigt Tilleg C indeholder oversatte sikkerhedsadvarsler der vedrgrer installation af dette udstyr N r De ser symbolet amp skal De sl op i tilleg C og finde de oversatte sikkerhedsadvarsler i Deres eget sprog Belangrijk Appendix C bevat vertaalde veiligheidsopmerkingen voor het installeren van deze apparatuur Wanneer u de amp ziet raadpleeg Appendix C voor vertaalde veiligheidsinstructies in uw taal Important L annexe C contient les instructions de s curit relatives l installation de cet quipement Lorsque vous voyez le symbole amp reportez vous l annexe C pour consulter la traduction de ces instructions dans votre langue T rke Liite C sis lt t m n laitteen asentamiseen liittyv t k nnetyt turvaohjeet Kun n et 4 symbolin katso k nnetty turvaohjetta liitteest C Importante Appendice C contiene avvisi di sicurezza tradotti per l installazione di questa apparecchiatura Il simbolo amp indica
10. Atencion El cable de alimentacion se usa como un dispositivo de desconexion Para desactivar el equipo desconecte el cable de alimentaci n Peligro De Rayos Peligro NO REALICE NINGUN TIPO DE TRABAJO O CONEXION en los equipos o en LOS CABLES durante TORMENTAS ELECTRICAS AN No bloquee las aberturas para ventilacion AN No conectar ninguna l nea telef nica al conector de se ales Temperatura Requerida Para La Operaci n Este producto est dise ado para una temperatura ambiental m xima de 40 grados C Para Todos Los Pa ses Monte el producto de acuerdo con los C digos El ctricos locales y nacionales 64 Translated Electrical Safety and Emission Information 2 63 od amp 5 6 Standarder Denna produkt uppfyller f ljande standarder Radiost rning EN55022 Klass A FCC Part 15 Klass A Immunitet EN55024 Els kerhet EN60950 UL60950 FCC Part 68 S kerhet Anv nd endast medf ljande kraftaggregat till DSL konverteraren AT MC602 kan installeras frist ende eller monterad i AT MCR12 enheten I det senare fallet beh ver AT MC602 inte kraftaggregatet Varning N tkabeln anv nds som str mbrytare f r att koppla fr n str mmen dra ur n tkabeln Fara F r Blixtnedslag Fara ARBETA EJ p utrustningen eller kablarna vid ASKVADER e H AN Blockera inte luftventilerna a 8 A Koppla inte telefonledning till signalkontakten 6 9 amp 10 Driftstemperatur Denna produkt r konstruerad f r rumste
11. C60XCONF No answer from device Figure 32 No Answer Error Message This error message may occur when your computer is not responding in which case you should re start your computer and try again Q Communication error the program will be closed Verify serial connection and restart the program as shown in Figure 33 Fatal Error Communication error the program will be closed Werify serial connection and restart the program Figure 33 Communication Error Message 48 Troubleshooting If you are unable to establish a configuration session with the network extender and receive this error message check to be sure that the management cable is securely connected to the management port on the network extender and to the RS 232 port on the computer Then make sure you are selecting the correct COMI or COM2 port at the software prompt Max speed cannot be lower than min speed select different values This error message occurs when you select a maximum speed that is lower than the set minimum speed during the selection of speed ranges on the rate adaptation section on the Configuration menu screen Select a higher maximum value to correct the problem P side must be connected to start this procedure or S side must be connected to start this procedure These error messages occur when the management cable is connected to the wrong unit for the procedure you are trying to perform This could happen if y
12. Extended Ethernet AT MC601 AT MC602 Installation and User s Guide gt Allied Telesyn Simply connecting the world Copyright O 2004 Allied Telesis K K www alliedtelesyn com All rights reserved No part of this publication may be reproduced without prior written permission from Allied Telesis K K Microsoft is a registered trademark of Microsoft Corporation Netscape Navigator is a registered trademark of Netscape Communications Corporation All other product names company names logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners Allied Telesis K K reserves the right to make changes in specifications and other information contained in this document without prior written notice The information provided herein is subject to change without notice In no event shall Allied Telesis K K be liable for any incidental special indirect or consequential damages whatsoever including but not limited to lost profits arising out of or related to this manual or the information contained herein even if Allied Telesis K K has been advised of known or should have known the possibility of such damages Electrical Safety and Emission Statement Standards This product meets the following standards Warning In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures RFI Emission EN
13. KANSSA SALAMOINNIN AIKANA ev A l tuki ilmareiki 8 A l liit puhelinlinjaa signaalin liittimeen 9 A K ytt l mp tila T m tuote on suunniteltu ymp r iv n ilman maksimil mp tilalle amp 10 40 C Kaikki Maat Asenna tuote paikallisten ja kansallisten s hk turvallisuusm r ysten mukaisesti 60 Translated Electrical Safety and Emission Information 63 od amp 5 amp 6 67 9 amp 10 Standard Questo prodotto conforme ai seguenti standard Emissione RFI interferenza di EN55022 Classe A FCC Part 15 Classe A radiofrequenza Immunit EN55024 Sicurezza elettrica EN60950 UL60950 FCC Part 68 Norme Di Sicurezza Questo dispositivo deve essere alimentato solo mediante il proprio adattatore Il dispositivo AT MC602 puo essere installato a sel stante o puo essere inserito nell unita AT MCR 12 In questo ultimo caso il dispositivo AT MC602 non richiede l adattatore Attenzione Il cavo di alimentazione usato come dispositivo di disattivazione Per togliere la corrente al dispositivo staccare il cavo di alimentazione Pericolo Di Fulmini Pericolo NON LAVORARE sul dispositivo o sui CAVI durante PRECIPITAZIONI TEMPORALESCHE A Non ostruire le prese d aria A Non collegare una linea telefonica al connettore del segnale Temperatura Di Funzionamento Questo prodotto concepito per una temperatura ambientale massima di 40 gradi centigradi Tutti I Paesi ins
14. ach corner of the bottom of the unit as illustrated in Figure 6 1ANHIHL3 CIONILXA 1S0A LO9DIN IV mm 1 490 PIV a AN i Figure 6 Attaching Protective Feet to the Subscriber Unit The Subscriber unit can be mounted onto a wall using the keyholes on the bottom of the unit The screws and plastic anchors used for mounting the unit are provided To wall mount the Subscriber Unit perform the following procedure 1 Ifattached remove the protective feet data cables and power cord from the unit 2 Select a wall location for the device 24 Installation 3 Install the screws and plastic anchors onto the wall as shown in Figure Ji MVA Figure 7 Installing the Screws and Plastic Anchors Onto The Wall 4 Position the switch onto the wall screws so that the ports are facing the ceiling as shown in Figure 8 Cimo OOOO Figure 8 Positioning The Switch Onto The Wall Screws 25 AT MC601 AT MC602 Installation and User s Guide Cabling the To cable the Subscriber unit perform the following steps Subscriber Unit 1 First connect the Ethernet cable from the Ethernet port to the Ethernet port on the computer as shown in Figure 9 Figure 9 Ethernet to Computer 2 Then connect a telephone line cable from the PSTN port to the telephone as shown in Figure 10 Figure 10 PSTN to Telephone 26 Installation 3 Next connect a teleph
15. as adaptador de energia fornecido pelo extens o O AT MC602 pode ser instalado de maneira independente ou pode ser colocado dentro da unidade AT MCR12 No ltimo caso o AT MC602 n o precisa de adaptador de energia es 5 Cuidado O cabo de alimentac o utilizado como um dispositivo de desconex o Para deseletrificar o equipamento desconecte o cabo de ALIMENTAC O 64 6 Perigo De Choque Causado Por Raio Perigo N O TRABALHE no equipamento ou nos CABOS durante per odos suscet veis a QUEDAS DE RAIO es 7 A N o bloqueie as aberturas de ventilag o amp 8 N N o conecte uma linha telef nica ao conector de sinal ed Temperatura De Funcionamento Este produto foi projetado para uma temperatura ambiente maxima de 40 graus centigrados amp 10 Todos Os Pa ses Instale o produto de acordo com as normas nacionais e locais para instalag es el tricas 63 2 amp 3 amp 5 66 67 68 9 amp 10 AT MC601 AT MC602 Installation and User s Guide Est ndares Este producto cumple con los siguientes est ndares Emisi n RFI EN55022 Clase A FCC Part 15 Clase A Inmunidad EN55024 Seguridad el ctrica EN60950 UL60950 FCC Part 68 Seguridad Use nicamente el adaptador de corriente suministrado junto con el extensor El extensor AT MC602 puede ser instalado en stand alone o puede ser insertado en la unidad AT MCR12 En este ultimo caso el extensor AT MC602 no necesita el adaptador de corriente suministrado
16. back panel of the AT MCR 12 chassis If the network extender stands alone make sure that the provided adapter is securely connected to the power source and to the power connector on the back panel of the network extender Verify that the power outlet has power by connecting another device to it Q Try connecting the network extender to another power source Try using a different power cord or a different power adapter Check that the voltage from the power source is within the required levels for your region 47 AT MC601 AT MC602 Installation and User s Guide Verify that the ACT LED for each twisted pair port is ON If a ACT LED is OFF do the following Q Verify that the end node connected to the port is powered ON and is operating properly Q Check that the twisted pair cable is securely connected to the port on the network extender and to the port on the end node Q Make sure that the twisted pair cable does not exceed 100 meters 328 feet Q Verify that you are using the appropriate category of twisted pair cable Category 3 or better for 10 Mbps operation Category 5 and Category 5E for 100 Mbps operation A Make sure that the operating parameters of the port on the network extender are compatible with the end node to which the port is connected Error Messages When using the configuration software you may encounter the following error messages Q No answer from device as shown in Figure 32 AT M
17. components from the shipping package and store the packaging material in a safe location Note You must use the original shipping material if you need to return the unit to Allied Telesyn 2 Place the network extender on a level secure surface 3 Make sure the following hardware components are included in your network extender package If any item is missing or damaged contact your Allied Telesyn sales representative for assistance A One AT MC601 or AT MC602 Network Extender Four protective feet Two Phillips head screws for wall mounting Two plastic anchors for wall mounting One cable lug One M4 x 8mm screw One power adapter One management cable provided for AT MC602 model only Documentation and configuration software CD D O D D LO D C oc Warranty and registration card 23 AT MC601 AT MC602 Installation and User s Guide Installing the AT MC601 Subscriber Unit Using the Subscriber Unit on a Desktop Wall Mounting the Subscriber Unit The AT MC601 Subscriber unit will most likely be used as a stand alone device or can be used as a desktop device or mounted onto a wall using the keyholes on the bottom of the unit The screws and plastic anchors used for mounting the unit are provided To use the Subscriber unit on a desktop perform the following procedure 1 Remove all equipment from the package and store the packaging material in a safe place 2 Attach the four protective feet provided to e
18. configure and manage your AT MC601 and AT MC602 VDSL network extenders you need to download a copy of the configuration software onto the computers you will use to manage the units The AT S57 configuration software is included on the Documentation CD provided with the units New releases of the AT S57 configuration software are available from the Allied Telesyn Web site at www alliedtelesyn com or from our FTP server at ftp alliedtelesyn com To log on to the FTP server enter anonymous for the user name and your email address for the password Management software for the AT MC601 and AT MC602 VDSL network extenders will have S57 as part of the file name Once you have a copy of the software on your computer connect the Provider unit to your computer using the management cable provided as shown in Figure 23 Attach the 9 pin RS 232 end of the cable to the COM 1 or COM 2 port on your computer Attach the 8 pin DIN end of the cable to the management port on the unit Figure 23 Connecting the Management Cable If the network extender is not already on power on the unit using the power cable provided Refer to Powering On the Subscriber Unit on page 27 for further instructions on how to power on the unit 36 Configuration Opening the Open the configuration software by double clicking the ATS57 Configuration application icon as you would with any other software program The AT Software MC60x Configurator pop up w
19. d appendices Chapter 1 Product Description describes the features and components of the network extenders Chapter 2 Installation contains installation instructions for each unit Chapter 3 Configuration explains how to use the configuration software The AT S57 software is used to configure the network extenders Chapter 4 Troubleshooting provides information on how to resolve common problems that might occur with the network extenders Appendix A Default Settings lists the default software settings Appendix B Technical Specifications lists the technical specifications for the network extenders Appendix C Translated Electrical Safety and Emission Information contains multi language translations of the warnings and cautions in the manual Preface Document Conventions This document uses the following conventions Note Notes provide additional information Warning Warnings inform you that performing or omitting a specific action may result in bodily injury Caution Cautions inform you that performing or omitting a specific action may result in equipment damage or loss of data AT MC601 AT MC602 Installation and User s Guide Contacting Allied Telesyn Technical Support Online Support E mail and Telephone Support Returning Products For Sales or Corporate Information Obtaining Management Software Updates This section provides Allied Telesyn contact information for technical support as
20. d preferred direction is Low High Choosing a negotiation direction determines how the modem searches for speeds When set to Low High the modem will start at minimum speeds and keeps negotiating progressively higher speeds until it has achieved its maximum speed for the connection Apply Press the Apply button to set your data transfer rates and negotiation direction selections About Use the About button to display the version number of the AT S57 configuration software 40 Configuration VDSL Status To view the VDSL Status screen click on the VDSL Status tab at the top of the menu The VDSL Status screen is displayed in Figure 28 AT MC60x Configurator link DOWN EA E E Ef y js ju ja MEME Figure 28 VDSL Status The parameters on the VDSL Status screen are described below These parameters are for viewing and monitoring purposes only They cannot be changed manually SNR of Received Signal The Signal to Noise Ratio on the VDSL line measured in decibels The SNR is a parameter of the constellation of the receive signal Corrected RS errors s Number of corrected Reed Solomon errors per second Mean Square Error An indication of the symbol error rate measured in decibels Full Constellation Link The highest possible QAM Quadrature Amplitude Modulation constellation which enables the highest line rates 41 AT MC601 AT MC602 Installation and User s Guide Reduced Constellation Link
21. di consultare I Appendice C per l avviso di sicurezza nella propria lingua Viktig Tillegg C inneholder oversatt sikkerhetsinformasjon for installering av dette utstyret N r du ser 4 pner du til Tillegg C for finne den oversatte sikkerhetsinformasjonen p gnsket spr k Importante O Anexo C cont m advert ncias de seguran a traduzidas para instalar este equipamento Quando vir o s mbolo 7 leia a advert ncia de seguran a traduzida no seu idioma no Anexo C Importante El Ap ndice C contiene mensajes de seguridad traducidos para la instalaci n de este equipo Cuando vea el s mbolo amp vaya al Ap ndice C para ver el mensaje de seguridad traducido a su idioma Obs Bilaga C inneh ller versatta s kerhetsmeddelanden avseende installationen av denna utrustning N r du ser 47 skall du g till Bilaga C f r att l sa det versatta s kerhetsmeddelandet p ditt spr k Contents Electrical Safety and Emission Statement 3 Predio A Re dotum ts 6 How This Guide 1 Ore ani Zed WE 6 Document TU EE H Contacting Allied Telesyn Technical SUpport sizes iaia aaa enden deerde 8 Online Support 8 E mail and Telephone Support 8 Returning Products 8 For Sales or Corporate Information 8 Obtaining Management Software Updates 8 Chapter 1 Product Description AA a 9 Summa ry of HE 9 OVERVIEW 6 sof doses keen eee 10 Location of Components semis id ica o ita 11 Hardware Features cui eto tet POPE A e ORDER set 12 VDSE
22. dial 32 Powering On the Provider Unit e 33 Warranty RESIS that OM mee aeneon 34 Chapter 3 Configuration EE 35 Startino a Configuration SESSION eseon ee ammensi eee re Preig burn rende add seen su 36 Downloading Software Updates 36 Cabling Preparations a titio t Uie e laicale aii 36 Opening the Configuration Software 37 Confisurins the Provider Unt eoi sak Eee aee e Gal paves Peleo ree Geduld da 38 Longo Eet e ee 38 VDSE Stats C D mimi aia 41 Ethernet Status india 43 Contisurins the Subscriber Unit oriri e dne res eet hee dere deese Sa 45 Chapter 4 Troubleshooting ot oa aioe epee eh LA die n epe OP eeu b aac 47 LEEDS 47 Error Messages eo UR Sen rl om 48 Appendix A Default Configuration Settings verennou uere ae Rer e eh rea ie e temen 51 Appendix B Technical Specifications nuire o ree eer P tecti PO e ebd SATAMIEN ANT 52 Physical Specificatiornis tete utet D Der sin I ROGO DERE UU HH en eds ne RR 52 Environmental Specifications coil ii 52 Power Specifications onec eme ana e p EROR E REO HO D PETER PEU E rie Iren 52 Safety and Electromagnetic Compatibility Certifications ss 53 Appendix C Translated Electrical Safety and Emission Information A 54 Preface This guide contains instructions on how to install and configure the AT MC601 and AT MC602 Extended Ethernet units How This Guide is Organized This manual contains the following chapters an
23. e following items Q One cable lug provided Q One M4 x 8mm screw provided A Crimping tool not provided Q One 12 AWG stranded wire or 14 AWG solid wire not provided Warning Make sure to attach the frame to ground before you power on the chassis To ground the unit to the ground point perform the following procedure Useacrimping tool to affix the provided cable lug to one end of the 12 AWG bundled or 14 AWG solid ground wire 2 Insert the M4 screw into the cable lug as illustrated in Figure 16 Figure 16 Inserting M4 Screw into the Cable Lug 3 Secure the cable lug with the M4 screw to the rear panel of the Provider unit as illustrated in Figure 17 j e G Figure 17 Securing Cable Lug with M4 Screw 4 Attach the other end of the ground wire to an appropriate ground earth rod of the building 30 Installation Rack Mounting To install the Provider unit in an AT MCR12 rackmount chassis perform the Provider the following steps Unit 1 Attach the unit to one of the sliders that will hold the unit in the chassis as shown in Figure 18 Figure 18 Rack Mount Set on Slider 2 Then set the slider in the chassis as shown in Figure 19 Figure 19 Rack Mount Set in Rack 31 AT MC601 AT MC602 Installation and User s Guide Cabling the To cable the Provider unit perform the following steps Provider Unit 1 First connect the Ethernet cable from the Ethernet port to the Serv
24. e installed stand alone or can be inserted in the AT MCR12 chassis In the last case the AT MC602 does not need the power adapter s 5 Caution Power cord is used as a disconnection device To de energize equipment disconnect the power cord 6 Lightning Danger Danger Do not work on equipment or cables during periods of lightning activity 67 AN Do not block air vents s 8 N Do not connect a telephone line into the signal connector ed A Operating Temperature This product is designed for a maximum ambient temperature of 40 degrees C amp 10 A All Countries Install product in accordance with local and National Electrical Codes 55 2 amp 3 amp 4 amp 5 66 AT MC601 AT MC602 Installation and User s Guide Normen Dieses Produkt erf llt die Anforderungen der nachfolgenden Normen Hochfrequenzst rung EN55022 Klasse A FCC Part 15 Klasse A St rsicherheit EN55024 Elektrische Sicherheit EN60950 UL60950 FCC Part 68 Sicherheit Bitte den Adapter nur mit dem mitgelieferten Extender benutzen Die AT MC602 kann einzeln benutzt werden oder in der AT MCR12 Einheit Im letzteren Fall braucht der AT MC602 keinen Adapter Vorsicht Das netzkabel dient zum trennen der stromversorgung Zur trennung vom netz kabel aus der steckdose ziehen Gefahr Durch Blitzschlag Gefahr Keine Arbeiten am Ger t oder an den Kabeln w hrend eines Gewitters ausf hren 67 N Entl ftungs ffnungen nicht versperren 8 A Verbind
25. en Sie nicht das Telefonkabel mit dem Signalverbindungsstecker 9 amp 10 Betriebstemperatur Dieses Produkt wurde fiir den Betrieb in einer Umgebungstemperatur von nicht mehr als 40 C entworfen Alle L nder Installation muf rtlichen und nationalen elektrischen Vorschriften entsprechen 56 Translated Electrical Safety and Emission Information Standarder Dette produkt tilfredsstiller de f lgende standarder amp 1 Radiofrekvens forstyrrelsesemission ENS5022 Klasse A FCC Part 15 Klasse A amp 2 Immunitet EN55024 63 Elektrisk sikkerhed EN60950 UL60950 FCC Part 68 Sikkerhed ord Ved installation af converteren m man kun benytte den med kgbte PSU AT MC602 converteren kan installeres som enkelt node eller installeres i et AT MCR12 chassis Ved installation i AT MCR12 chassis skal man ikke benytte PSU en amp 5 Advarsel Den str mf rende ledning bruges til at afbryde str mmen Skal str mmen til apparatet afbrydes tages ledningen ud af stikket 6 Fare Under Uvejr Fare UNDLAD at arbejde p udstyr eller KABLER i perioder med LYNAKTIVITET amp 7 N Ventilations bningerne m ikke blokeres 8 A Tilslut ikke telefonledninger til signalstikforbindelsen ed Betjeningstemperatur Dette apparat er konstrueret til en omgivende temperatur pa maksimum 40 grader C amp 10 Alle Lande Installation af produkter skal ske i overensstemmelse med lokal og national lovgivning for elektriske installationer 57
26. ese occasions follow the procedure described in Starting a Configuration Session on page 36 and then continue with the instructions in this section After you have selected the correct port and clicked the OK button the AT MC60x Configurator Select Mode screen will appear as displayed in Figure 30 AT MC60x Configurator x r Select Mode C Install ome Figure 30 Select Mode There are two options on the Select Mode screen Normal and Install These options are described below Normal The Normal mode sets the units to operate under normal parameters The units will attempt to establish a link using the parameters you set on the Configuration screen while connected to the Provider unit See Configuration on page 38 for a description of the Configuration screen Using the Normal mode will only allow the units to establish links that meet the criteria you have set The disadvantage to using the Normal mode 1s that 1f either of the upstream or downstream speeds you have set are unattainable the link attempt will fail because the units are not set to use the default parameters as back ups Install The Install mode enables a watchdog timer to monitor the link attempt process If the network extenders are not able to establish a link using the parameters you set on the Provider unit within a reasonable amount of 45 AT MC601 AT MC602 Installation and User s Guide time a timeout will occur Afte
27. ettings Setting Default Provider Parameters Monitored Local Provider Speeds Upstream Max 94 Mbps Upstream Min 94 Mbps Downstream Max 94 Mbps Downstream Min 94 Mbps Flow Low to High Selected Ethernet Port Duplex Mode Auto Negotiate Speed Auto Negotiate MDI MDI X Auto Link Recovery Subscriber Unit Mode Normal 51 Appendix B Technical Specifications Physical Specifications Dimensions WxDxH 109 mm x 95 mm x 25 mm 4 29 in x 3 74 in x 0 98 in Weight 27 kg 0 6 lbs Recommended Minimum Clearance on All Sides 5 08 cm 2 0 in Environmental Specifications Operating Temperature 0 C to 40 C 32 F to 104 F Storage Temperature 25 C to 70 C 13 F to 158 F Operating Humidity 5 to 90 noncondensing Storage Humidity 5 to 95 noncondensing Operating Altitude 3 000 m approx 10 000 ft Non operating Altitude 4 000 m approx 13 100 ft Power Specifications Power Consumption 6 Watts Input Supply Current 500 mA Input Supply Voltage 12V DC 52 Technical Specifications Safety and Electromagnetic Compatibility Certifications Emission EN55022 ClassA FCC Part15 ClassA Immunity EN55024 Safety EN60950 UL60950 FCC Part68 53 Appendix C Translated Electrical Safety and Emission Information Important This appendix contains multiple language translations for the safety statements in this guide W
28. extender register your product by completing the enclosed warranty card and mailing it to Allied Telesyn 34 Chapter 3 Configuration The configuration software allows you to adjust and monitor the operating parameters of the media converter Some of the functions that you can perform with the software include A Determine the VDSL link status Q Set the upstream and downstream data transfer rates Q Monitor the status of the VDSL parameters on both the local and remote units Q Monitor the status of the Ethernet parameters on both the local and remote units Q Link recovery The AT S57 configuration software is included on the Documentation CD included with the network extender The default settings may be adequate for some networks and may not need to be changed If this is true for your network then you can use the network extenders by simply connecting the units to your network as explained in Installation on page 18 Note The default settings for the configuration software can be found in Appendix A on page 51 To actively configure a network extender by changing or adjusting its operating parameters you must access the AT S57 software while connected to the AT MC602 Provider unit The AT S57 software has a menu interface that makes it very easy to use 35 AT MC601 AT MC602 Installation and User s Guide Starting a Configuration Session Downloading Software Updates Cabling Preparations In order to
29. ice Provider box in your wiring closet as shown in Figure 20 Internet Service Provider z Figure 20 Ethernet to Internet Service Provider 2 Then connect a telephone line cable from the PSTN port to the outside telco box as shown in Figure 21 Figure 21 PSTN to Telco PBX Line 32 Installation 3 Next connect a telephone line cable from the VDSL Line port to the wall interior telephone line as shown in Figure 22 so that the Provider unit can communicate with the Subscriber unit gt Wall Interior Phone Line A Figure 22 VDSL Line to Wall Interior Phone Line Note The procedure for connecting the management cable is described in Cabling Preparations on page 36 Powering On the Powering on the AT MC602 Provider Unit requires that the host Provider Unit equipment AT MCR12 rackmount chassis is powered on as well A Warning The QUALIFIED SERVICE PERSONNEL must verify that the AT MCR12 power cord is connected to the socket provided with the ground conductor If the power cord is not connected the QUALIFIED SERVICE PERSONNEL must install a permanent ground connection using the bond stud on the rear panel of the AT MCR12 chassis For detailed information on how to power on the AT MCR 12 unit refer to the AT MCR12 Media Converter Rackmount Chassis Installation Manual 33 AT MC601 AT MC602 Installation and User s Guide Warranty Registration When you have finished installing the network
30. ichtig Dieser Anhang enth lt bersetzungen der in diesem Handbuch enthaltenen Sicherheitshinweise in mehreren Sprachen Vigtigt Dette till g indeholder overs ttelser i flere sprog af sikkerhedsadvarslerne i denne h ndbog Belangrijk Deze appendix bevat vertalingen in meerdere talen van de veiligheidsopmerkingen in deze gids Important Cette annexe contient la traduction en plusieurs langues des instructions de s curit figurant dans ce guide T rke T m liite sis lt t ss oppaassa esiintyv t turvaohjeet usealla kielell Importante questa appendice contiene traduzioni in pi lingue degli avvisi di sicurezza di questa guida Viktig Dette tillegget inneholder oversettelser til flere spr k av sikkerhetsinformasjonen i denne veiledningen Importante Este anexo cont m tradug es em v rios idiomas das advert ncias de seguranga neste guia Importante Este ap ndice contiene traducciones en m ltiples idiomas de los mensajes de seguridad incluidos en esta gu a Obs Denna bilaga inneh ller flerspr kiga vers ttningar av s kerhetsmeddelandena i denna handledning 54 Translated Electrical Safety and Emission Information Standards This product meets the following safety standards ol RFI Emission EN55022 Class A FCC Part 15 Class A es 2 Immunity EN55024 63 Electrical Safety EN60950 UL60950 FCC Part 68 Safety 4 Only use the power adapter supplied with the extender The AT MC602 can b
31. ill appear as shown in Figure 24 AT MC60x Configurator X Select Serial Port com y About Figure 24 AT MC60x Configurator If you would like to verify that you are using the latest version of the configuration and management software click the About button on the bottom right of the AT MC60x Configurator pop up The About AT MC60x Configurator pop up will appear as shown in Figure 25 About AT MC60x Configurator x AT MCB x Configurator Version 2 0 0 ER Allied Telesyn I Copyright C 2001 Figure 25 About AT MC60x Configurator Select the computer port you are using from the pull down menu on the AT MC60x Configurator pop up and click OK If you are connected to the AT MC602 Provider unit and want to configure the network extenders continue with the next section Configuring the Provider Unit on page 38 If you are connected to the AT MC601 Subscriber unit to attempt link recovery continue with Configuring the Subscriber Unit on page 45 37 AT MC601 AT MC602 Installation and User s Guide Configuring the Provider Unit Configuration After performing the procedure described in the previous section Starting a Configuration Session on page 36 if you are connected to the Provider unit the AT MC60x Configurator menu will appear The Configurator bar at the top of the menu indicates whether or not the Provider unit has established an Ethernet link by displaying link
32. llation This chapter contains the installation procedures for the network extenders The installation process is described in the following sections Q D O ODD Installation Safety Precautions A Selecting a Site for the Network Extender Required Cables Unpacking the Network Extender Installing the AT MC601 Subscriber Unit Installing the AT MC602 Provider Unit Warranty Registration Installation Installation Safety Precautions Please review the following safety precautions before you begin to install the network extenders Refer to Translated Electrical Safety and Emission Information on page 54 for translated safety statements in your language Caution Only use the power adapter supplied with the extender The AT MC602 can be installed stand alone or can be inserted in the AT MCR12 chassis In the last case the AT MC602 does not need the power adapter 47 4 A Caution Power cord is used as a disconnection device To de energize equipment disconnect the power cord amp 5 Warning Lightning Danger Do not work on this equipment or cables during periods of lightning activity amp 6 Caution Air vents The air vents must not be blocked on the unit and must have free access to the room s ambient air for cooling amp 7 Caution Operating Temperature This product is designed for a maximum ambient temperature of 40 C a 9 N Caution All Countries Install this product in accordance with local and
33. mperatur ej verstigande 40 grader Celsius Alla L nder Installera produkten i enlighet med lokala och statliga best mmelser f r elektrisk utrustning 65
34. nal AC DC Power Adapter AT MC601 AT MC602 Installation and User s Guide Table 5 lists the management cable connector pins and their signals Table 5 Management Cable Pinouts RS 232 Pin DIN Pin Signal 1 1 Not Used 2 2 TXD 3 8 RXD 4 5 DSR 5 6 GND 6 3 DTR 7 4 CTS 8 7 RTS 9 N A Not Used The network extender has a single DC power supply socket on the back panel The unit does not have a power switch To turn the network extender ON or OFF you connect or disconnect the power cord An external AC DC power adapter is included with the network extender for desktop or wall mount operation The power adapter supplies 12V DC to the network extender Allied Telesyn supplies an approved safety compliant AC power adapter specifically designed for each region the network extender is sold Each type of power adapter has an unregulated output of 12V DC at 1A Product Description Software Features The AT S57 software used to configure the AT MC601 and AT MC602 network extenders has the following features a a a Determine the VDSL link status Set the upstream and downstream data transfer rates Monitor the status of the VDSL parameters on both the local and remote units Monitor the status of the Ethernet parameters on both the local and remote units Link recovery Note The features listed here are further described in Configuration on page 35 Chapter 2 Insta
35. one line cable from the VDSL Line port to the wall interior telephone line as shown in Figure 11 so that the Subscriber unit can communicate with the Provider unit Wall Interior Phone Line Figure 11 VDSL Line to Wall Interior Phone Line Note The procedure for connecting the management cable is described in Cabling Preparations on page 36 Powering On the Power on the Subscriber unit using the power adapter provided as shown Subscriber Unit in Figure 12 Figure 12 Power On The Subscriber Unit 27 AT MC601 AT MC602 Installation and User s Guide Installing the AT MC602 Provider Unit Using the Provider Unit on a Desktop The AT MC602 Provider unit can be installed in an AT MCR12 rackmount chassis used as a desktop device or mounted onto a wall using the keyholes on the bottom of the unit The screws and plastic anchors used for mounting the unit are provided Warning To prevent exposure to electric shock the AT MC602 Provider Unit must be installed in a RESTRICTED ACCESS LOCATION and performed by QUALIFIED SERVICE PERSONNEL Note For Finland Norway and Sweden When the AT MC602 and the AT MCR12 are used a permanent ground conductor must be installed on the AT MCR12 chassis For installation instructions of this ground conductor refer to the A7 MCRI2 Media Converter Rackmount Chassis Installation Manual PN 613 10725 00 To use the Provider unit on a desktop perform the following procedu
36. ou switch the management cable between the units without closing the software window Simply switch the management cable to the other unit to correct the problem Can t read link status This message occurs when the software cannot read the link status from the Provider side Perform the procedure described in Configuring the Subscriber Unit on page 45 to see if link recovery on the Subscriber unit solves the problem Please run this program on S side to set it in Install mode If S side is already in install mode then configuration can not be achieved as shown in Figure 34 AT MC60XCONF Please run this program on S side to set it in Install mode IFS side is already in install mode then configuration can not be achieved Figure 34 Run on S Side Error Message This error message occurs when the Provider unit cannot achieve the link with the S or Subscriber side unit using the default speeds value Set the Subscriber to Install Mode as described in Configuring the Subscriber Unit on page 45 49 AT MC601 AT MC602 Installation and User s Guide Configuration file was not found Syntax error in configuration file Configuration cannot be achieved These last three error messages indicate a problem with the configuration software Try re loading the software onto your computer 50 Appendix A Default Configuration Settings This appendix lists the AT MC601 and AT MC602 default s
37. peut etre installe d une facon autonome ou insere dans le AT MCR12 chassis Dans le deuxieme cas le AT MC602 n a pas besoin de l adapteur aleatoire es 5 Attention Le cordon d alimentation sert de mise hors circuit Pour couper l alimentation du mat riel d brancher le cordon amp 6 Danger De Foudre Danger NE PAS MANIER le mat riel ou les C BLES lors d activit orageuse es 7 A Ne pas bloquer les fentes d a ration ar 8 A Ne pas connecter une ligne t l phonique au connecteur de signaux amp 9 Temp rature De Fonctionnement Ce mat riel est capable de tol rer une temp rature ambiante maximum de 40 degr s Celsius amp 10 Pour Tous Pays Installer le mat riel conform ment aux normes lectriques nationales et locales 59 2 amp 3 amp 4 amp 5 66 AT MC601 AT MC602 Installation and User s Guide Standardit T m tuote on seuraavien standardien mukainen Radioaaltojen h irint EN55022 Class A FCC Part 15 Class A Kest vyys EN55024 S hk turvallisuus EN60950 UL60950 FCC Part 68 Turvallisuus K yt vain muuntimen mukana toimitettua virtalaitetta AT MC602 voidaan k ytt itsen isesti tai asennettuna AT MCR12 kehikkoon j lkimm isess tapauksessa AT MC602 ei tarvitse erillist virtalaitetta Huomautus Virtajohtoa k ytet n virrankatkaisulaitteena Virta katkaistaan irrottamalla virtajohto Salamaniskuvaara Hengenvaara ALA TY SKENTELE laitteiden tai KAAPELEIDEN
38. r a timeout the default configuration parameters will be used to establish a link with the highest possible speed The default configuration parameters start at 0 94 Mbps upstream and downstream with negotiation set from Low gt High Select the option that corresponds to your mode choice and click the Apply button When the mode has been set the AT MC60x Configurator Done message will appear as displayed in Figure 31 AT MC60XCONF Done Figure 31 Done Message When you have finished setting the mode on the Subscriber unit click the Close button on the bottom right of the AT MC60x Configurator menu to exit from the configuration software 46 Chapter 4 Troubleshooting LEDs This chapter contains information on how to troubleshoot the AT MC601 and AT MC602 network extenders in the event a problem occurs Note If after following the instructions in this chapter you are unable to resolve the problem contact Allied Telesyn Technical Support for assistance Refer to Contacting Allied Telesyn Technical Support on page 8 for information on how to contact our Technical Support Department Check the PWR LED on the front of the network extender If the LED is OFF indicating that the network extender is not receiving power do the following a If the network extender is inserted in the AT MCR12 chassis make sure that the power cord is securely connected to the power source and to the power connector on the
39. r the bottom of the rack If you are installing the network extender on a table be sure that the table is level and secure The power outlet for the network extender should be located near the unit and should be easily accessible The site should provide for easy access to the ports on the front of the network extender This will make it easy for you to connect and disconnect cables as well as view the LEDs To allow proper cooling of the network extender air flow around the unit and through its vents on the side should not be restricted Do not place objects on top of the network extender Do not expose the network extender to moisture or water Make sure that the site is a dust free environment You should use dedicated power circuits or power conditioners to supply reliable electrical power to the network extenders 21 Cables Not Included AT MC601 AT MC602 Installation and User s Guide The AT MC601 and AT MC602 network extenders require the three cables described in Table 6 below These cables are not included with the network extenders Table 6 Cables Port Cable Connector Ethernet Category 3 or better 100 ohm unshielded straight through or crossover twisted pair cable RJ 45 PSTN standard telephone cable RJ 11 VDSL Line standard telephone cable RJ 11 22 Installation Unpacking the Network Extender To unpack the network extender 1 Remove all
40. re Remove all equipment from the package and store the packaging material in a safe place 2 Attach the four protective feet provided to each corner of the bottom of the unit as illustrated in Figure 6 13NY3H13 CIONILXA 1S0A ZO90N L ASIA PAIN SA A PENSEI N1Sd gt INIT Hua lt 3NIT Figure 13 Attaching Protective Feet to the Provider Unit 28 Installation Wall Mounting The Provider unit can be mounted onto a wall using the keyholes on the the Provider bottom of the unit The screws and plastic anchors used for mounting the Unit unit are provided To wall mount the Provider Unit perform the following procedure 1 Ifattached remove the protective feet data cables and power cord from the unit Select a wall location for the device Install the screws and plastic anchors onto the wall as shown in Figure 7 6 e o AVAA h Figure 14 Installing the Screws and Plastic Anchors Onto The Wall 4 Position the switch onto the wall screws so that the ports are facing the ceiling as shown in Figure 8 4 N N N ISSN Figure 15 Positioning The Switch Onto The Wall Screws 29 AT MC601 AT MC602 Installation and User s Guide Grounding the When an AT MC602 Provider unit is used as a standalone network Provider Unit extender you must ground the unit to a ground point to ensure a safe and proper operation Grounding the chassis requires th
41. s 4 22 5 63 7 50 8 44 11 26 15 01 16 88 upstream only This field will display Select speed to set until you have selected data rates from the upstream and downstream pull down menus and set the rates by clicking the Apply button Then reports on the status of the attempt to configure the speeds selected from the upstream and downstream pull down menus will appear in this field A successful configuration attempt will cycle though the following status reports Looking for link status Checking signal noise ratio Loading a Configuration DS 1 41 US 2 81 This report will keep repeating with progressively higher upstream and downstream values until the set rate or the highest possible rate has been achieved Saving config on EEPROM S Side Saving config on EEPROM P Side Done 39 AT MC601 AT MC602 Installation and User s Guide The Configuration Saved pop up shown in Figure 27 will appear when the set rate or the highest possible rate has been achieved AT MC60xConf X Configuration saved Figure 27 Configuration Saved An unsuccessful configuration attempt may include the following status reports Loading defaults Can t read link status Done These negative status reports may also be accompanied by error message pop ups Error messages are explained in Troubleshooting on page 47 HIGH LOW LOW HIGH Allows you to choose the negotiation direction for the modem speed The default an
42. tallare il prodotto in conformit delle vigenti normative elettriche nazionali 61 2 amp 3 amp 4 amp 5 66 67 68 9 amp 10 AT MC601 AT MC602 Installation and User s Guide Sikkerhetsnormer Dette produktet tilfredsstiller f lgende sikkerhetsnormer RFI str ling EN55022 Klasse A FCC Part 15 Klasse A Immunittet EN55024 Elektrisk sikkerhet EN60950 UL60950 FCC Part 68 Sikkerhet Ved installation av converteren m man kun benytte den med tilhgrende PSU AT MC602 converteren kan installeres som enkel node eller installeres i et AT MCRI2 chassis Ved installation i AT MCR12 chassis skal man ikke benytte PSU en Forsiktig Strgmledningen brukes til frakoble utstyret For deaktivisere utstyret m str mforsyningen kobles fra Fare For Lynnedslag Fare ARBEID IKKE p utstyr eller KABLER i TORDENVAR A Blokker ikke luftventilene A Telefonlinje m ikke koples til signalkontakten Driftstemperatur Dette produktet er konstruert for bruk i maksimum romtemperatur p 40 grader celsius Alle Land Produktet m installeres i samsvar med de lokale og nasjonale elektriske koder 62 Translated Electrical Safety and Emission Information Padr es Este produto atende aos seguintes padr es e 1 Emiss o de interfer ncia de EN55022 Class A FCC Part 15 Class A radiofrequ ncia amp 2 Imunidade EN55024 e 3 Seguran a el ctrica EN60950 UL60950 FCC Part 68 Seguranga 4 A Use apen
43. ted to a port on a bridge which is typically wired as MDI the port on the network extender automatically configures itself as MDI X This feature allows you to use either straight through or crossover cables when connecting devices to the network extender AT MC601 AT MC602 Installation and User s Guide Auto Negotiation The network extenders Auto Negotiate the speed and duplex mode of the Ethernet link so that the link comes up in the highest performance configuration supported by both ends Half and Full duplex Mode Duplex mode refers to the way an end node sende and receives data on the network An end node can operate in either half or full duplex mode depending on its capabilities An end node that is operating in half duplex mode can either send data or receive data but it cannot do both at the same time An end node that is operating in full duplex mode can send and receive data simultaneously The best network performance is achieved when an end node can operate at full duplex since the end node is able to send and receive data simultaneously The AT MC601 and AT MC602 network extenders can operate in either half or full duplex mode The network extender can operate with end nodes capable of either half duplex full duplex or that can Auto Negotiate the duplex mode However it is important to remember that the two end nodes connected to the ports on the network extenders must be able to operate in the same duplex mode
44. the Ethernet Status screen are described below TxRx Counters The data fields in this section indicate the number and type of frames that have been transmitted and received via the Ethernet link Collision Counters The data fields in this section indicate the number and type of collisions that have occurred on the Ethernet link Error Counters The data fields in this section indicate the number and type of errors that have occurred on the Ethernet link Clear This button allows you to reset the counters clearing the values previously recorded by the software 43 AT MC601 AT MC602 Installation and User s Guide Stop Start This button allows you to pause counting When you press Stop the counters remain at their present values When you press Start the counters continue adding to the values already recorded by the software Local Remote Select Local to view the parameters for the Provider unit Select Remote to view the parameters for the Subscriber unit The Remote option will only be available when an active link has been established 44 Configuration Configuring the Subscriber Unit In rare instances you may need to use the configuration software on the Subscriber unit to attempt link recovery If the configuration software detects a problem with the Subscriber unit while you are connected to the Provider unit it will prompt you to use the software on the Subscriber unit by displaying a pop up error message On th
45. to the wall provided that the chassis is connected to an appropriate ground rod Refer to Installing the AT MC602 Provider Unit on page 28 for installation details These units are easy to install They can be configured and managed through the MGMT port using the software provided on the installation CD When both the AT MC601 Subscriber and the AT MC602 Provider have been installed the network extender system topology shown in Figure 1 is complete Computers Al Telephone Ethernet Port AT MC601 Subscriber 5 ER EN man VDSL Line through wall interior phone line AT MC602 W on Provider em U n it Seat ETHERNET Internet Service Li Provider Line Figure 1 Network Extender System Topology Product Description Location of Components Figure 2 illustrates the front panels of the AT MC601 and AT MC602 network extenders AT MC601 Ethernet EI nd a VDSL Line Status LINK LEDs LEDs i CE ss AT ae ETHERNET Management Port VDSL Line Port Ethernet Port PSTN Port AT MC602 Ethernet eo gt Status ACT LEDs uen EN VDSL Line LINK LEDs MV Allied Telesyn AT MC602 VDSL EXTENDED ETHERNET PWR Figure 2 Front Panels Figure 3 illustrates the rear panels of the AT MC601 and AT MC602 network extenders AT MC601 e DC Power Supply Port AT MC602 B So o
46. us as the user name and your email address for the password Chapter 1 Product Description The AT MC601 AT MC602 Extended Ethernet products are designed to transmit data at very high speeds over unshielded pairs of copper wires using VDSL technology on your existing telephone line Summary of Features VDSL Very high bit rate Digital Subscriber Line port PSTN Public Switched Telephone Network port 10 100 Mbps Ethernet port with an RJ 45 connector Auto MDI MDI X D O D D O Auto Negotiation for speed and duplex mode IEEE 803 3u compliant Status LEDs Management port AT S57 configuration software D O O E 12V DC external power supply input port Overview AT MC601 AT MC602 Installation and User s Guide These devices can be used in multi dwelling units MDU multi tenant buildings MTU and in the hospitality industry such as airports hotels and convention centers These units are sold in pairs with the AT MC601 functioning as the subscriber and the AT MC602 functioning as the provider In an MDU such as a university dormitory the subscriber unit would be installed in each room and connected to a provider unit through the telephone outlet Each AT MC602 or provider unit would be located in the building wiring closet The AT MC601 Extended Ethernet unit can be used as a desktop or wallmount device while the AT MC602 can be either installed in an AT MCRI2 chassis used as a desktop device or mounted on
47. well as sales or corporate information You can request technical support online by accessing the Allied Telesyn Knowledge Base from the following web site http kb alliedtelesyn com You can use the Knowledge Base to submit questions to our technical support staff and review answers to previously asked questions For Technical Support via E mail or telephone refer to the Support amp Services section of the Allied Telesyn web site http www alliedtelesyn com Products for return or repair must first be assigned a Return Materials Authorization RMA number A product sent to Allied Telesyn without a RMA number will be returned to the sender at the sender s expense To obtain a RMA number contact Allied Telesyn s Technical Support at our web site http www alliedtelesyn com You can contact Allied Telesyn for sales or corporate information at our web site http www alliedtelesyn com To find the contact information for your country select Contact Us then Worldwide Contacts New releases of management software for our managed products can be downloaded from either of the following Internet sites Allied Telesyn web site http www alliedtelesyn com Allied Telesyn FTP server ftp ftp alliedtelesyn com If you would prefer to download new software from the Allied Telesyn FTP server from your workstation s command prompt you will need FTP client software and you will be asked to log in to the server Enter anonymo
Download Pdf Manuals
Related Search