Alliance Laundry Systems FLW1525C User's Manual
Contents
1. H0541 Figure 2 802951 O Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Installation Step 2 Position and Level the Washer Al wanno Washers elevated above floor level must be anchored to that elevated surface base or platform The material used to elevate the washer should also be anchored to the floor to ensure that the washer will not walk or that the washer can not be physically pulled tipped or slid from its installed position Failure to do so may result in conditions which can produce serious injury death and or property damage Position washer so it has sufficient clearance for installation and servicing NOTE Use of the dispenser drawer or washer door as a handle in the transportation of the washer may cause damage to the dispenser or door Place washer in position on a solid sturdy and level floor Installing the washer on any type of carpeting soft tile a platform or other weakly supported structures is not recommended Place a level on the cabinet top and check if the washer is level from side to side and front to back NOTE Level must rest on raised portion of top panel Refer to Figure 3 If washer is not level tilt washer to access the front and rear leveling legs For easier access to leveling legs prop up washer with a wooden block Refer to Figure 3 Loosen 7 8 in locknut and adjust legs until the washer is level from side to side and2. malfunction or breakdown grounding will reduce the risk of electric shock by providing a path of least resistance for electric current The washer is equipped with a cord having an equipment grounding conductor and a three prong grounding plug The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances A wanne Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or service person if you are in doubt as to whether the washer is properly grounded DO NOT modify the plug provided with the washer if it will not fit the outlet have a proper outlet installed by a qualified electrician NOTE Have a qualified electrician check the polarity of the wall receptacle If a voltage reading is measured other than that in Figure 14 the qualified electrician should correct the problem 802951 O Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Installation Step 10 Check Installation Refer to Installer Checklist on the back cover of this manual and make sure that washer is installed correctly Run washer through one complete cycle to make sure it is operating properly 15 Operation Operation Instructions IMPORTANT Prior to first wash use an all purpose cleaner or a detergent and water solution and a damp cloth to remove shipping
3. TRANSMIT 802951 Safety Information Explanation of Safety Messages Throughout this manual and on machine decals you will find precautionary statements DANGER WARNING and CAUTION followed by specific instructions These precautions are intended for the personal safety of the operator user servicer and those maintaining the machine Indicates an imminently hazardous situation that if not avoided will cause severe personal injury or death WARNING Indicates a hazardous situation that if not avoided could cause severe personal injury or death AL camo Indicates a hazardous situation that if not avoided may cause minor or moderate personal injury or property damage Additional precautionary statements IMPORTANT and NOTE are followed by specific instructions IMPORTANT The word IMPORTANT is used to inform the reader of specific procedures where minor machine damage will occur if the procedure is not followed NOTE The word NOTE is used to communicate installation operation maintenance or servicing information that is important but not hazard related 802951 O Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Important Safety Instructions Save These Instructions WARNING To reduce the risk of fire electric shock serious injury or death to persons when using your washer follow these basic precautions 1 Read all instructions
4. are unsatisfied with the service performed on your unit contact Alliance Laundry Systems Shepard Street P O Box 990 Ripon WI 54971 0990 U S A www comlaundry com Phone 920 748 3121 FLW2123N 1 Nameplate Figure 25 When calling or writing about your unit PLEASE GIVE THE MODEL AND SERIAL NUMBERS The model and serial numbers are located on the nameplate The nameplate will be in the location shown in Figure 25 Date Purchased Model Number Serial Number Please include a copy of your bill of sale and any service receipts you have WARNING To reduce the risk of serious injury or death DO NOT repair or replace any part of the unit or attempt any servicing unless specifically recommended in the user maintenance instructions or in published user repair instructions that you understand and have the skills to carry out W329 If replacement parts are required contact the source from where you purchased your washer or call 920 748 3950 for the name and address of the nearest authorized parts distributor 24 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 802951 Installer Checklist Fast Track for Installing the Washer Refer to the manual for more detailed information 0 e Remove the Shock Sleeves and Shipping Brace Position Washer Near Installation Area FLW2124N C CHECK Wi
5. dust from inside of washtub IMPORTANT Remove all sharp objects from laundry to avoid tears and rips to items during normal machine operation Step 1 Load Laundry Load items loosely into wash drum NOTE Small items such as baby socks may get caught around the door Place these articles inside a mesh garment bag Step 2 Close Loading Door Close loading door tightly The washer will not operate with the loading door open FLW2227N FLW2226N Figure 15 When washing bulky items such as blankets and comforters use the DELICATES BULKY cycle The cycle includes agitation and final spin speeds that maintain the load s balance and minimize wear to the articles Figure 16 16 O Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 802951 Step 3 Add Laundry Supplies Open dispenser drawer Measure and add low sudsing high efficiency HE detergent 1 bleach 2 and fabric softener 3 to the dispenser drawer refer to Figure 17 Close dispenser drawer IMPORTANT If using non HE detergent avoid oversudsing by using 1 2 of the detergent manufacturer s recommended amount FLW2236N mb Detergent Bleach Fabric Softener oO N Figure 17 AL camo Dispenser drawer requires a special tool for removal Contact a service person if removal is necessary W236 80295
6. maximum hot water temperature is 125 Fahrenheit 51 Celsius Warm water is a mixture of hot and cold water Warm water temperature is dependent upon water temperature and pressure of both the hot and cold water supply lines A wanno To prevent personal injury avoid contact with inlet water temperatures higher than 125 Fahrenheit 51 Celsius and hot surfaces Water pressure must be a minimum of 20 to a maximum of 120 pounds per square inch 138 to 827 kPa static pressure measured at the faucet NOTE Water pressure under 20 pounds per square inch 138 kPa will cause an extended fill time in the washer and may not properly flush out the detergent dispenser O Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 802951 Turn on the water supply faucets and flush the lines for approximately two minutes to remove any foreign materials that could clog the screens in the water mixing valve NOTE When installing in newly constructed or renovated building it is very important to flush the lines since build up may have occurred during construction Connecting Hoses Insert each filter screen into the end of each fill hose that will connect to the water supply faucet The screen must be facing outward Refer to Figure 4 Insert each plain rubber washer into the other end of each fill hose that will connect to the water mixing valve at the rear of the washer Refer to Figure 4 Thread hose couplings
7. onto valve connections finger tight then approximately 1 4 turn with pliers IMPORTANT DO NOT cross thread or overtighten couplings Turn water on and check for leaks If leaks are found retighten the hose couplings Continue tightening and rechecking until no leaks are found TLW1976N Faucet Fill Hoses Plain Rubber Washer Filter Screens khOND Figure 4 Installation IMPORTANT Hoses and other natural rubber parts deteriorate after extended use Hoses may develop cracks blisters or material wear from the temperature and constant high pressure they are subjected to All hoses should be checked on a monthly basis for any visible signs of deterioration Any hose showing the signs of deterioration listed above should be replaced immediately All hoses should be replaced every five years WATER MIXING VALVE FLW1974N Water Supply Faucets Hot Water Connection Cold Water Connection Fill Hoses kOoOnD Figure 5 IMPORTANT Turn off water supply faucets after check out and demonstration Owner should turn off water supply whenever there will be an extended period of non use NOTE Longer fill hoses are available as optional equipment at extra cost if the hoses supplied with the washer are not long enough for the installation Order hoses as follows No 20617 Fill Hose 8 feet 2 44 m No 20618 Fill Hose 10 feet 3 05 m 802951 O Copyrig
8. user to insert coins or card to satisfy the vend price When INSERT COINS CARD is lit the digits show the vend price remaining to be satisfied WASH WASH is lit during the WASH portions of the cycle RINSE RINSE is lit during the RINSE portions of the cycle SPIN SPIN is lit during the final spin portion of the cycle DOOR DOOR is lit whenever the door is locked The door cannot be opened when this light is on LIGHT LIGHT is lit when the LIGHT soil level is selected MEDIUM MEDIUM is lit when the MEDIUM soil level is selected HEAVY HEAVY is lit when the HEAVY soil level is selected START START flashes one second on and one second off when the full vend price has been satisfied Operation IMPORTANT If washer fails to operate properly after installation make sure electrical service and water supply faucets are turned on Are all the controls properly set Have a qualified service person refer to the wiring diagram located inside of washer control cabinet and check for broken loose or incorrect wiring NOTE Once a cycle has started the door can only be opened by first unplugging the power cord and waiting one minute Al wanno To reduce the risk of bodily injury do not remove laundry from washer until all lights are out and all moving parts have stopped W092 802951 O Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 19 Maintenance User Maintenance Instructions Lubri
9. your washer in good condition Bumping or dropping the washer can damage safety features If this occurs have your washer checked by a qualified service person If the supply cord is damaged it must be replaced by a special cord or assembly available from the manufacturer or its service agent Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 20 21 22 23 24 25 26 27 Be sure water connections have a shut off valve and that fill hose connections are tight CLOSE the shut off valves at the end of each wash day Loading door MUST BE CLOSED any time the washer is to fill tumble or spin DO NOT bypass the loading door switch by permitting the washer to operate with the loading door open Always read and follow manufacturer s instructions on packages of laundry and cleaning aids Heed all warnings or precautions To reduce the risk of poisoning or chemical burns keep them out of the reach of children at all times preferably in a locked cabinet Always follow the fabric care instructions supplied by the garment manufacturer Never operate the washer with any guards and or panels removed DO NOT operate the washer with missing or broken parts DO NOT bypass any safety devices Failure to install maintain and or operate this washer according to the manufacturer s instructions may result in conditions which can produce bodily injury and or property damage NOTE The WARN
10. 1 Operation Step 4 Set Fabric Selector Push touchpad for NORMAL PERM PRESS or DELICATES BULKY cycle Light indicates selection NOTE Changes can be made to Fabric Selector setting up until the first fill is complete Y E A IBULKY N SOIL LEVEL START O y FLW2228N Figure 18 Step 5 Set Wash Temperature Push touchpad for HOT WARM or COLD Light indicates selection NOTE Always follow manufacturer s care labels XD FLW2229N Figure 19 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 17 Operation Step 6 Set Soil Level Push Soil Level touchpad to select LIGHT MEDIUM or HEAVY Light indicates selection FLW2230N Figure 20 Step 7 Insert Coin s or Card To Insert Money Insert coin s in coin slot Check pricing as seen on digital display X 7 O W3871 Figure 21 To Insert Card Insert card into opening INSERT CARD HERE C Lam aa DRY1927N Figure 22 18 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Step 8 Start Washer After vend price has been satisfied push the START pad DOOR MUST BE CLOSED TO START WASHER J i PERM DELICATES NORMAL Gm O Qu T SOIL LEVEL uor bu FLW2231N Figure 23 802951 Indicator Lights INSERT COINS CARD INSERT COINS CARD is lit to prompt the
11. 13 for the injection interface label CHEMICAL INJECTION ELECTRICAL INTERFACE SOFTENER DISPENSER SOFTENER CONNECTION RELAY DETERGENT A DISPENSER Be RELAY YELLOW BLACK CONNECTION RED BLACK NO CONNECTION TERMINAL BLOCK NOTE Normally Open Contacts Contacts Close to Start Chemical Injection Maximum Load Connection per Contact 1A 120VAC 240VAC 801653R1 FLW2028N Figure 13 These terminals may be used to provide signals to the supply injection system but must not be used to provide power to the actual pump Any injection system pump which requires 110 VAC must be powered by a separate external power source Control Function Test The washer should be cleaned after the installation is complete A function test should then be executed on the unloaded machine 1 Check the power supply for such characteristics as correct voltage phase and cycles to be certain they are correct for the washer 2 Open manual shut off valves to the washer 3 Apply power to the washer Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 13 Installation Step 9 Plug In the Washer Electrical Requirements 120 Volt 60 Hertz with 3 Prong Grounding Plug NOTE The wiring diagram is located in the control cabinet Al wanna To reduce the risk of fire electric shock serious injury or death all wiring and grounding MUST conform with the latest edition of the National Electrical Co
12. 259N 1 1 5 in 3 81 cm Inside Diameter 1 86 in 4 72 cm Outside Diameter 802951 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT Installation Before You Start Tools For most installations the basic tools you will need are a khON D0741 Wrench Screwdriver Pliers Socket Wrench Level Figure 1 NOTE An 8 in 20 32 cm coin drawer is required for coin operated models NOTE If the washer is delivered on a cold day below freezing or is stored in an unheated room or area during the cold months do not attempt to operate it until the washer has had a chance to warm up NOTE Install dryer before washer This allows room for attaching exhaust duct NOTE Some moisture in the wash drum is normal Water is used during testing at the manufacturer O Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 802951 Installing the Washer Step 1 Position Washer Near Installation Area Move washer so that it is within 4 feet 1 2 meters of the desired area of installation NOTE For best performance and to minimize vibration or movement install washer on a solid sturdy and level floor Some floors may need to be reinforced especially on a second floor or over a basement Do not install the washer on carpeting soft tile a platform or other weakly supported structures
13. Frontload Washers Metered Commercial NOTA Para bajar una copia de estas instrucciones en espa ol visite www comlaundry com S FLW1525C Keep These Instructions for Future Reference If this machine changes ownership this manual must accompany machine VNlance Laundry S ystems www comlaundry com Part No 802951R3 August 2010 uonerodo uonejesuy AL rana Failure to install maintain and or operate this machine according to the manufacturer s instructions may result in conditions which can produce bodily injury and or property damage NOTE The WARNING and IMPORTANT instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur It must be understood that common sense caution and carefulness are factors which cannot be built into these washers These factors MUST BE supplied by the person s installing maintaining or operating the washer Always contact the distributor service agent or the manufacturer about any problems or conditions you do not understand 802951 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 1 Safety Inf OO tica 3 Tab le of afety Information Explanation of Safety Messages ooooooconoccnocononononannncnncnnnncnn nooo ncnnccnnccnnos C O nt e nt S Important Safety Instructions oonconccnnnnnocononoconaconcnnnnnnn conc nono ncncc nono 3 Installation te tp A ia 5 Dimensions and Specif
14. ING and IMPORTANT SAFETY INSTRUCTIONS appearing in this manual are not meant to cover all possible conditions and situations that may occur Common sense caution and care must be exercised when installing maintaining or operating the washer Always contact your dealer distributor service agent or the manufacturer about any problems or conditions you do not understand 802951 Installation Dimensions and Specifications 2 in 7 B 5 1 cm gt 24 in 61 0 cm a 36 94 in 93 83 cm 42 25 in 107 2 cm Stainless Steel Models hrough Serial No 1005018719 43 in 109 2 cm All Other Models 31 1 in 79 cm gt 29 6 in 75 1 cm o Q N n Ma 26 9 in 68 3 cm 28 in 71 1 cm a pele gt o 2 in ER 5 1 cm 3 8 cm MODELS EQUIPPED WITH DRAIN HOSE FLW2258N 36 94 in 93 83 cm 42 25 in 107 2 cm Stainless Steel Models hrough Serial No 1005018719 43 in 109 2 cm All Other Models 7 31 1 in 79 cm gt 29 6 in 75 1 cm o N z y la a 28 in 71 1 cm _ 4 1 in R E 10 41 cm 10 67 cm 1 5 in 3 8 cm 26 9 in 68 3 cm MODELS WITH GRAVITY DRAIN FLW2
15. ance Laundry Systems LLC DO NOT COPY or TRANSMIT 802951 Troubleshooting Washer Symptom Possible Cause Solution Vibrates Moves e Make sure washer is level Uneven leveling can cause vibration Slightly e Make sure washer is installed on a solid sturdy and level floor The washer should not be installed on carpeting soft tile a platform or other weakly supported structures e Make sure rubber feet are installed on all four leveling legs Refer to Installation section step 5 Is Noisy e Make sure washer is level Uneven leveling can cause vibration e Some sounds may be a part of normal operation for a frontload washer Load is too Wet e Wash load may be unbalanced The washer may have limited the spin speed to prevent damage to the machine Redistribute the load e Load is too small Add items to make full load Wrong Water e Make sure that the controls are properly set Temperature e Check fill hoses Make sure hot faucet hose is connected to hot mixing valve indicated with H on the valve bracket and cold faucet is connected to cold mixing valve indi cated with C on the valve bracket e Make sure laundry room water heater is adjusted properly 802951 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 23 Contact Information If service is required contact the nearest Factory Authorized Service Center If you are unable to locate an authorized service center or
16. before using the washer 2 Refer to the GROUNDING INSTRUCTIONS in the INSTALLATION manual for the proper grounding of the washer 3 Do not wash articles that have been previously cleaned in washed in soaked in or spotted with gasoline dry cleaning solvents or other flammable or explosive substances as they give off vapors that could ignite or explode 4 Do not add gasoline dry cleaning solvents or other flammable or explosive substances to the wash water These substances give off vapors that could ignite or explode 5 Under certain conditions hydrogen gas may be produced in a hot water system that has not been used for two weeks or more HYDROGEN GAS IS EXPLOSIVE If the hot water system has not been used for such a period before using a washing machine or combination washer dryer turn on all hot water faucets and let the water flow from each for several minutes This will release any accumulated hydrogen gas The gas is flammable do not smoke or use an open flame during this time 6 Do not allow children to play on or in the washer Close supervision of children is necessary when the washer is used near children This is a safety rule for all appliances 7 Before the washer is removed from service or discarded remove the door to the washing compartment 8 Do not reach into the washer if the wash drum is moving 9 Do not install or store the washer where it will be exposed to water and or weather 10 D
17. cation All moving parts are sealed in a permanent supply of lubricant or are equipped with oilless bearings Additional lubrication will not be necessary Do not lubricate the door hinge If the hinge makes noise replace the hinge Cold Weather Care If the washer is delivered on a cold day below freezing or is stored in an unheated room or area during the cold months do not attempt to operate it until the washer has had a chance to warm up Care of Your Washer Use only a damp or sudsy cloth for cleaning the control panel Some cleaning product sprays may harm the finish on the control panel or damage the interior Wipe the washer cabinet as needed If detergent bleach or other washing products are spilled on the cabinet wipe immediately Some products will cause permanent damage if spilled on the cabinet Do not use scouring pads or abrasive cleansers The wash drum will need no particular care although it may need rinsing or wiping after an unusual load has been washed The outside of the door window can be cleaned with household window cleaner Running an occasional rinse cycle with bleach will help to avoid a musty smell in the wash drum Cleaning Glass Sealing Area In order to assure that the door properly seals against water leaks the following surfaces should be wiped off periodically e The outside perimeter of the door glass where the seal contacts the glass e The front surface of the door seal li
18. de ANSI NFPA No 70 and such local regulations as might apply It is the customer s responsibility to have the wiring fuses and circuit breakers installed by a qualified electrician to make sure adequate electrical power is available to the washer When plugging in the washer e DO NOT overload circuits e DO NOT use an extension cord e DO NOT use an adapter e DO NOT operate other appliances on the same circuit Use separately fused 15 Amp circuits The washer is designed to be operated on a separate branch polarized three wire effectively grounded 120 Volt 60 Hertz AC alternating current circuit protected by a 15 ampere fuse equivalent fusetron or circuit breaker The three prong grounding plug on the power cord should be plugged directly into a polarized three slot effectively grounded receptacle rated 110 120 Volts AC alternating current 15 Amps Refer to Figure 14 to determine correct polarity of the wall receptacle Standard 120 Volt 60 Hertz 3 Wire Effectively Grounded Circuit DRY2022N L1 Ground Neutral Side Round Grounding Prong Neutral arhond Figure 14 WARNING To reduce the risk of an electric shock or fire DO NOT use an extension cord or an adapter to connect the washer to the electric power source 14 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 802951 Grounding Instructions The washer must be grounded In the event of
19. ectrical supply Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 21 Troubleshooting Try these troubleshooting tips before making a service call They may save time and money Washer Symptom Possible Cause Solution Won t Fill Make sure power cord is plugged all the way into the electrical outlet Make sure hot and cold water faucets are turned on Make sure that the fill hoses are not kinked or twisted Press START keypad Make sure that the controls are properly set Make sure that the loading door is closed tightly Check the laundry room fuse or circuit breaker Clean the screens in the water mixing valve and the filter screens located at the faucet end of the fill hoses Won t Start Make sure loading door is closed tightly Press START keypad Make sure power cord is plugged all the way into the electrical outlet Check the laundry room fuse or circuit breaker Insert coin s or card Make sure door latch is properly adjusted relative to door lock Won t Spin Tumble Make sure loading door is closed tightly Press START keypad Make sure power cord is plugged all the way into the electrical outlet Make sure controls are properly set Check the laundry room fuse or circuit breaker Broken drive belt Call the service person Foreign object trap in pump may be clogged Clean the trap Refer to Maintenance section Stops Pauses During Cycle Pauses are part of the
20. einstalled Disconnect washer from electrical supply While supporting the front access panel remove two screws from the bottom edge of the panel Gently lower the panel to remove it from the washer Place the shock sleeves on all four shock absorbers Refer to Figure 24 Insert hooked end of shipping brace into the open slot of the motor mount Refer to Figure 24 Attach the brace with the five bolts and washers Refer to Figure 24 Reinstall front access panel FLW2124N Shock Sleeves Motor Mount Hooked End of Shipping Brace Bolts and Lockwashers khORND Figure 24 Refer to Installation section step 6 for proper procedures whenever the washer is moved 802951 Maintenance Cleaning Foreign Object Trap The washer s pump has a trap that may collect foreign objects The trap may need to be cleaned if water is draining slower than usual To clean Disconnect washer from electrical supply While supporting the front access panel remove two screws from the bottom edge of the panel Gently lower the panel to remove it from the washer NOTE The pump may have some water in it Use a rag or a container to catch water If the wash drum is full of water use a wet dry shop vacuum to catch the water With rag or vacuum ready unscrew the cap on the left side of the pump and remove trap Clean the debris from the trap Reinstall the trap and access panel Reconnect washer to el
21. emperature eee eeecnecereeeeecnaeceeeeeeeeeaees 17 Step 6 Set Soll Level annie id gel ogee aes 18 Step 7 Insert Coin s or Card cece eescceesececeeceeeeecenecceeaeeeeeeeeseees 18 Step S Start Washer siii ibs alactensasenseena levtenseewstes sess 18 Indicator Ligia dpi 19 Maintenance iia Aa 20 User Maintenance Instructions ooconconnnnnocononcconaconanannnancnnncrnononnccnnccnnos 20 Lubricati n cities Dni rr caos 20 Cold Weather Catia lite irradia 20 Careof Your Washeluacuiio idiota iii 20 Cleaning Glass Sealing Area ocoonconnccnoccconaconnconnnnnnnnnn con ncrnncnnncnnncnnos 20 Replacing Hoses unnsa nare a rosita iis 20 Filter Scores i lle eiii 20 Vacations and Extended Non USe ooococococinoconoccnocnconoconaconacnnccnanannos 20 Reinstallation of Shipping Materials onconconnncnnonnnccnonaconncnnncnnnannos 21 Cleaning Foreign Object Trap oo eee ceeeeecsseeeeeeeeecnsecnseceaeenseeees 21 Troubleshooting 35 s05 05 scsscesseciessaess nies age iaeesesioensenta seas 22 Contact Information sisi cscs ceeleseclersselstkae cd atesneueles dai 24 Installer Checklist oonnonininnnninnnnnoninioninnanicnonanicinannnos Back Cover Copyright 2010 Alliance Laundry Systems LLC All rights reserved No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher 2 Copyright Alliance Laundry Systems LLC DO NOT COPY or
22. front to back using a level Washer should not rock Tighten the locknuts securely against the washer base using the 7 8 in wrench If the locknuts are not tight washer will move out of position during operation Installation NOTE DO NOT slide washer across floor if the leveling legs have been extended as legs and base could become damaged Remove rubber feet from accessories bag and place on all four leveling legs Verify that unit doesn t rock FLW2114N Leveling Leg Washer Base Level Wood Block Locknut Rubber Foot oa hwnd Figure 3 Step 3 Connect Fill Hoses Al wanno Under certain conditions hydrogen gas may be produced in a hot water system that has not been used for two weeks or more HYDROGEN GAS IS EXPLOSIVE If the hot water system has not been used for such a period and before using the washer turn on all hot water faucets and let the water flow from each for several minutes This will release any accumulated hydrogen gas The gas is flammable Do not smoke or use an open flame during this time W029 Water Supply Water supply faucets must fit standard 3 4 inch 19 1 mm female garden hose couplings DO NOT USE SLIP ON OR CLAMP ON CONNECTIONS Water supply faucets should be readily accessible to permit turning them off when washer is not being used Recommended cold water temperature is 60 to 80 Fahrenheit 16 to 27 Celsius Recommended
23. ht Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 9 Installation Risers Risers or air cushions may have to be installed if the pipes knock or pound when flow of water stops The risers are more efficient when installed as close as possible to the water supply faucets refer to Figure 6 WO005 1 Risers Air Cushions 2 Water Supply Faucets Figure 6 Step 4 Non Gravity Drain Models Only Connect Drain Hose to Drain Receptacle Remove the drain hose from its shipping position on the rear of the washer by removing the shipping tape IMPORTANT Drain receptacle must be capable of handling a minimum of 1 3 8 inch 3 5 cm outside diameter drain hose E FLW1963N 1 Shipping Tape Figure 7 10 O Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 802951 Standpipe Installation Place the drain hose into the standpipe Remove the beaded tie down strap from accessories bag and place around standpipe and drain hose and tighten strap to hold hose to standpipe Refer to Figure 8 This will prevent the drain hose from dislodging from drain receptacle during use 24 TO 36 in 61 TO 91 44 cm RECOMMENDED HEIGHT FLW1964N 1 Standpipe 2 in 5 08 cm or 1 1 2 in 4 cm Figure 8 Installation Step 5 Gravity Drain Models Only Connect Drai
24. ications cc eeececeseeceeeeeeeeesecsseceeesseeeeeeaes 5 Before Y OWStarteint neetecve lade s 6 Tools stevie A A han ee Gael eae nee 6 Installing the Was hernia dd do 7 Step 1 Position Washer Near Installation Area eee 7 Step 2 Position and Level the Washer ooooonncnnncnnccnooccnocananonacananonn 7 Step 3 Connect Fill Hoses iieiea 8 Step 4 Non Gravity Drain Models Only Connect Drain Hose to Drain Receptacle 10 Step 5 Gravity Drain Models Only Connect Drain Outlet to Drain System ee eeeeeeeeereeeneeenees 11 Step 6 Remove the Shock Sleeves and Shipping Brace 12 Step 7 Wipe Out Inside of Wash Drum ooooonocnnccnoccconnconnnonnconncnanos 12 Step 8 Supply Injection Models Only Connect External Supplies to WasheT ooooonnncnnncnoncnnccconncnancnancnanon 12 Control Function Test usina iia 13 Step 9 Plug In the Washer oooonononnocccnonccnocccconcnononanonnccnnn E s 14 Step 10 Check Installation ooooonncnnnccnnconocanocononcnonononcnonacnnnnnncnanoo 15 Opera iii ee ote da is 16 Operation Instructions oooconnccnncnnoncnonononoconannn nono aao aiea ae Eaa crac 16 Step 1 Load Laundry enninu n a a a ica 16 Step 2 Close Loading Door eeeeeeeseeesecneeceeeseceeeeeaeeeaeeeeaees 16 Step 3 Add Laundry Supplies ooooonconnccconcninncnonconcconnonncnnccnanonancnanoo 17 Step 4 Set Fabric Select iise csc casks sccsuesisacesitsanebesdsceevssd chacdssceste 17 Step 5 Set Wash T
25. n Outlet to Drain System Remove drain fitting four inches long and hose clamp from accessories bag Insert drain fitting into drain outlet hose Clamp hose and fitting Connect the drain fitting to a vented drain system using a flexible connection obtain locally Inside diameter of fitting is 1 53 in 3 89 cm and outside diameter is 1 66 in 4 22 cm The drain system must be vented to prevent an air lock or siphoning IMPORTANT Increasing the drain hose length installing elbows or causing bends will decrease drain flow rates and increase drain times impairing machine performance FLW1935N 1 Drain Trough 2 Drain Outlet Hose Figure 9 802951 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 11 Installation Step 6 Remove the Shock Sleeves and Shipping Brace Remove front access panel by removing the two screws at the bottom of the panel Remove the five bolts and lockwashers from shipping brace with 9 16 in wrench and remove brace Refer to Figure 10 One is holding the brace to the weight Remove this bolt first Four bolts are located on the washer base Remove the two front bolts next and then the two rear bolts Remove all four shock sleeves by pulling on the yellow rope Remove label from front side of front access panel or shipping brace and place on backside of front access panel for future reference NOTE The shipping b
26. o not tamper with the controls Safety Information 11 12 13 14 15 16 17 18 19 Do not repair or replace any part of the washer or attempt any servicing unless specifically recommended in the user maintenance instructions or in published user repair instructions that you understand and have the skills to carry out To reduce the risk of an electric shock or fire DO NOT use an extension cord or an adapter to connect the washer to the electrical power source Use your washer only for its intended purpose washing clothes ALWAYS disconnect the washer from electrical supply before attempting any service Disconnect the power cord by grasping the plug not the cord Install the washer according to the INSTALLATION INSTRUCTIONS All connections for water drain electrical power and grounding must comply with local codes and be made by licensed personnel when required Do not do it yourself unless you know how To reduce the risk of fire clothes which have traces of any flammable substances such as vegetable oil cooking oil machine oil flammable chemicals thinner etc or anything containing wax or chemicals such as in mops and cleaning cloths must not be put into the washer These flammable substances may cause the fabric to catch on fire by itself Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product Keep
27. p Usually a mild soap solution will work If there is an extreme build up of minerals from a hard water supply the surfaces may need to be cleaned with a lime removal chemical Replacing Hoses Hoses and other natural rubber parts deteriorate after extended use Hoses may develop cracks blisters or material wear from the temperature and constant high pressure they are subjected to All hoses should be checked on a monthly basis for any visible signs of deterioration Any hose showing the signs of deterioration listed above should be replaced immediately All hoses should be replaced every five years Filter Screens Check the filter screens in the fill hoses for debris or damage annually Clean or replace them if necessary If the washer is filling with water slower than normal check the filter screens Clean or replace them if necessary Order filter screen Part No F270300 from the nearest authorized parts distributor Vacations and Extended Non Use IMPORTANT To avoid possible property damage due to flooding turn off the water supply to the washer whenever there will be an extended period of non use Leave the loading door open during extended periods of non use to allow the wash drum to dry out and avoid a musty smell 20 Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 802951 Reinstallation of Shipping Materials To prevent damage while moving the washer the shipping materials MUST be r
28. pe Out Inside of Wash Drum Position and Level the Washer FLW2115N C CHECK C CHECK 8 Supply Injection Models Only e Connect Fill Hoses e Connect External Supplies to Washer FLW2116N Non Gravity Drain Models Only Connect Drain Hose Plug In the Washer to Drain Receptacle D254IE0A C CHECK 9 CHECK Gravity Drain Models Only e Connect Drain Outlet to Drain System gt FLW1935N CHECK O Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT
29. r mixing valve Refer to Figure 12 3 Connect supply hoses to nozzles and secure with hose clamps obtain locally Refer to Figure 12 NOTE Hoses can be connected to either nozzle 4 Refer to supply injection system instructions and label inside washer junction box cover Figure 13 for electrical connection Do not attempt to make supply injection electrical connections to points other than those provided specifically for that purpose by the factory 5 Refer to supply injection system instructions for details on operation 12 O Copyright Alliance Laundry Systems LLC DO NOT COPY or TRANSMIT 802951 Supply Injection System Number of liquid supply connections 2 1 Detergent and 2 Softener Liquid supply connection size 3 8 9 52 in mm or 1 4 6 35 Wear eye and hand protection when handling chemicals always avoid direct contact with raw chemicals Read the manufacturer s directions for accidental contact before handling chemicals Ensure an eye rinse facility and an emergency shower are within easy reach Check at regular intervals for chemical leaks SW016 aa P Wi NRE ERE FLW2116N 1 Injection Point 2 Nozzle 3 Supply Dispenser Pump Outlet Figure 12 802951 Installation A junction box on the rear panel houses a terminal strip which furnishes supply output signals for the supply injection pumps Refer to Figure
30. race bolts washers and shock sleeves should be saved and MUST be reinstalled whenever the washer is moved more than four feet Refer to User Maintenance section for instructions Do not lift or transport washer from front or without shipping materials installed Store the shipping materials in the accessories bag Save materials for use whenever the washer is moved Reinstall front access panel IMPORTANT DO NOT tip washer more than 6 inches 152 4 mm in any direction after shipping brace has been removed Shock absorbers may separate and damage to washer may result For leveling purposes the washer may be tilted a maximum of 6 inches 152 4 mm in any direction FLW2124N Shock Sleeves Motor Mount Hooked End of Shipping Brace Bolts and Lockwashers khORND Figure 10 Step 7 Wipe Out Inside of Wash Drum Before using washer for the first time use an all purpose cleaner or a detergent and water solution and a damp cloth to remove shipping dust from inside wash drum FLW2115N Figure 11 Step 8 Supply Injection Models Only Connect External Supplies to Washer IMPORTANT Undiluted chemical dripping can damage the washer Ra Remove two nozzles from accessories bag Use either the 3 8 inch or 1 4 inch nozzles depending on the diameter of the dispenser tubing used 2 Attach nozzles to rear of machine Connection point located on cabinet above wate
31. washer s normal operation Wash load may be unbalanced Washer will stop and then restart spin automatically Check the laundry room fuse or circuit breaker Won t Drain Make sure drain hose is not kinked or twisted Make sure drain hose is not clogged Make sure drain receptacle is not clogged Refer to the Installation section to make sure that the drain hose has been properly installed Foreign object trap in pump may be clogged Clean the trap Refer to Maintenance section Water Leaks Check that fill hoses are properly installed on the faucets and the washer s water mixing valve Check the condition of the fill hoses Replace fill hoses every five years Check the condition of the rubber door gasket for tears or holes Make sure drain receptacle is not clogged Check building plumbing Laundry load may be oversudsing or overloaded Make sure you are using low sudsing high efficiency HE detergent and proper load sizes Make sure outside perimeter of the door glass where seal contacts glass is clean Too Many Soap Suds Laundry load may be oversudsing Make sure you are using low sudsing high efficiency HE detergent Make sure you are using the amount of detergent recommended on the detergent s label If using non HE detergent use only 1 2 of the detergent manufacturer s recommended amount Laundry load may be overloaded Make sure you are using proper load sizes 22 Copyright Alli
Download Pdf Manuals
Related Search