Airlink101 ASOHORL User's Manual
Contents
1. 32 bit PCI 10 100Mbps Fast Ethernet Adapter Model ASOHORL Quick Installation Guide Ver 1A FCC Class B Certification This equipment has been tested and found to comply with the regulations for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with this user s guide may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense CE Mark Warning This is a Class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Introduction Thank you for choosing the 32 bit PCI 10 100Mbps Fast Ethernet Adapter this Adapter is auto configurable upon power up and also supports auto negotiation to automatically select the optimum speed and communication mode of an attached device Additionally the 32 bit PCI Bus 10 100Mbps NWay ACPI Fast Ethernet Adapter complies with ACPI and PC99 and includes support for Remote Wake Up by Magic Packet LinkChg and Microsoft wake up frame About Fast Ethernet2. Fast Ethernet is a network technology specified by IEEE Standard 802 3u It extends the traditional 10Mbps Ethernet technology to achieve 100Mbps transmission and reception while retaining the same CSMA CD Ethernet protocol Thus while Fast Ethernet provides a tenfold increase in network capacity it is completely compatible with traditional 10Mbps Ethernet network facilities About Auto negotiation Auto negotiation is an IEEE 802 3 procedure of negotiating the highest data flow capability between the device in this case the Adapter and its link partner some other device The data flow information consists of the data speed 10Mbps or 100Mbps and data transfer half duplex or full duplex communication The physical process of auto negotiation requires only a few milliseconds to choose the fastest communications capability between the two devices Remote LAN Wakeup Remote LAN Wakeup capability is a key feature of a centrally managed PC environment This technology allows networked PCs to be powered up and managed from a central location at any time To utilize Remote LAN Wakeup three elements are required m Desktop management software that can send a wake up packet to the PC m A Wake On LAN enabled PC motherboard that can supply low level auxiliary power to a network Adapter when the PC is powered off m A Wake On LAN network Adapter that can recognize a wake up packet and signal the PC to power up A Wake On
3. LAN enabled PC is never completely powered off It maintains a low level auxiliary power supply to the motherboard The 3 wire Wake On LAN cable provides one line for the network Adapter auxiliary power and one line for the Adapter wake up signal the other line is ground If you have a PCI 2 1 slot then you do not need the Wake On LAN cable Even if the PC is powered off the network Adapter is always active and monitoring the network When a wake up packet is detected the Adapter signals the motherboard to power up the PC With the PC powered on maintenance and other support tasks can be performed Product Featues Designed for versatility and performance the 32 bit PCI bus 10 100Mbps Fast Ethernet Adapter provides the following features Compliant to IEEE 802 3 10BASE T standard Complaint to IEEE 802 3u 100BASE TX standard Compliant to IEEE ANSI 802 3 NWay Auto negotiation standard Compliant to PCI 2 1 2 2 standards Compliant to PC99 standard Supports Wake On LAN function for remote wake up AMD Magic Packet LinkChg and Microsoft wake up frame Supports 4 Wake On LAN WOL signals active high active low positive pulse and negative pulse Supports ACPI PCI power management Half Full duplex capability Supports Full Duplex Flow Control IEEE 802 3x Built in FIFO buffers reduce overhead of memory transfers Drivers for all leading Network Operating Systems Two LED indicators Link Activity Link In
4. dicator A steady green LED indicates good connection between the 32 bit PCI bus 10 100Mbps Fast Ethernet Adapter and its supporting hub Activity Indicator A flashing green LED indicates that the adapter is sending or receiving data 5 Installation Installation the 10 100Mbps PCI bus Fast Ethernet Adapter requires Hardware installation first then BIOS and Software installation Step 1 Hardware Installation 1 Switch off the computer unplug the power cord and remove the computer s cover Select an unused PCI slot and remove its protective bracket Carefully insert the Adapter and press until all the edge connectors are firmly seated inside the slot Then screw the Adapter s bracket securely into the PC s chassis Attach the Wake On LAN cable optional for PCI 2 1 motherboard If you require Wake On LAN capability attach one end of the 3 pin Wake On LAN cable to the connector on the top edge of the Adapter and the other end to the WOL connector on the computer s motherboard Refer to your computers installation manual to locate this connector Install the bracket screw which secures the Adapter to the computer s chassis Replace the computer s cover and connect the network cable to the newly installed network Adapter Reconnect the computer s power cord and plug it into the power outlet Step 2 BIOS Configuration Due to a fault in some Plug n Play BIOS programs it happens occasi
5. erly 1 Verify that the Adapter is fully and firmly seated in the slot connector 2 Check the length and rating of the connecting cables 3 Verify that the Adapter s PCI slot is not deactivated at the BIOS level The CMOS Setup utility of the computer ordinarily provides the option to activate or deactivate PCI slots 4 Replace the Adapter in question with a verified Adapter and run RSET8139 EXE diagnostic tests from the DIAG folder of the floppy disk 5 Install the Adapter to another PCI computer and run the tests again Remove all other PCI adapters from the computer and run the tests again If the verification diagnostic 8 test is not normal then there is probably an interrupt number conflict which will have to be resolved manually by the CMOS Setup utility after you have reinstalled all of the expansion Adapters Technical Support E mail support airlink101 com Toll Free 1 888 746 3238 Web Site www airlink101 com Copyright 2004 AirLink101 All rights reserved AirLink101 the stylized AirLink101 logo specific product designations and all other words and logos that are identified as trademarks and or service marks are unless noted otherwise the trademarks and service marks of AirLink101 All other product or service names are the property of their respective holders AirLink101 products are protected under numerous U S and foreign patents and pending applications mask work rights and copy
6. onally that a newly installed adapter is assigned an Interrupt Number which is already assigned to another device In such a case the conflict of Interrupt Number will cause faults in the behavior of both devices In that case it is necessary to run the CMOS Setup utility and manually assign a non conflicting Interrupt Number Step 3 Driver Installation Before you connect the 10 100Mbps PCI bus Adapter to the network you have to install the Adapter s driver first For most Windows operating systems the driver is already included with the OS The driver for each operating system is under a separate folder of the provided floppy disk A HELPME COM file under the root directory of the floppy disk lists the information and detailed installation procedure for all the available drivers Please refer to the HELPME COM file if you need assistance in installing the drivers Step 4 Boot ROM Installation optional The optional Boot ROM device allows you to connect a diskless workstation to the network Perform the following steps to install your Boot ROM device 1 Insert the Boot ROM into the socket on the Adapter 2 Refer to the installation procedures provided by the network operating system Troubleshooting If you experience any problems with the Adapter first verify that the appropriate driver is loaded that the proper grade of cable is employed for the network connection and that the supporting hub is functioning prop
7. rights 10
Download Pdf Manuals
Related Search