Aiphone MK-1MD User's Manual
Contents
1. 83659100 05976 lt gt AIPHONE MK Series DOOR SENTRY VIDEO ENTRY SECURITY INTERCOM Models M K 1 M D Main audio monitor station MK 1MD A INSTALLATION amp OPERATION MANUAL Before actually installing MK 1MD A the contents of this Manual must be thoroughly read and understood PRECAUTIONS ON INSTALLATION amp WIRING WARNING Negligence could result in death or serious injury to people GENERAL PRECAUTIONS Q General prohibitions 8 Prohibitions to subject the unit to water A WARNING Do not change or modify MK 1MD A equipment Do not connect any power source other than specified to terminals on MK 1MD A Doing so can cause fire or damage the unit Q The MK 1MD A equipment must not be exposed to water or any other liquid 9 Do not open MK 1MD A monitor unit The high voltage is inside Q Make sure wires are connected properly before plugging in the power supply S Keep AC outlet away from moisture and dust 7 Do not put any forcible strength on the monitor of MK 1MD A It can cause injury S A CAUTION Do not install or make any wire terminations while power supply is turned on It can cause electrical shock or damage the unit 2 Mount the MK 1MD A monitor on wall in a convenient location but not where it could be bumped or jarred A Q CAUTION Negligence could result in injury to people or damage to property Prohibitio2. Power source Power supply Image viewing area When camera is in horizontal position When camera is upwardly adjusted Communication MK DS A camera unit MK 1MD A monitor Scanning lines Minimum illumination Door release contact capacity Wiring Wiring distance Dimensions amp weight MK 1MD A DC 18V 0 8A 0 04A standby PS 18YC A AC 120V 50 60Hz PS 18YE AC 220 240V 50 60Hz each with secondary output DC 18V 1 2A 70cm V x 100cm H 2 3 V x 3 3 H 75cmV x 100cmH 2 5 V x 3 3 H Call in Image is on 30 sec Communication 2 1 2 min timed Extend with MONITOR button Common talk between rooms hang up either handset CCD camera with infrared LEDs 4 inch direct view flat CRT 525 lines Less than 1 Lux at 50cm 20 distance AC 12V 0 4A dry closure contact EL EL 2 wires parallel non polarized Aiphone 841802 in USA MK 1MD A to MK DS A 0 65mm 22AWG 18AWG Pes o MK 1SD A 210 1 D A 8 A 00 7 8 4 4159 This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference
3. to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful inteference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Increase the separation between the equipment and receiver Consult the dealer or an experienced radio TV technician for help WARRANTY Aiphone warrants its products to be free from defects of material and workmanship under normal use and service for a period of two years after delivery to the ultimate user and will repair free of charge or replace at no charge should it become defective upon which examination shall disclose to be defective and under warranty Aiphone reserves unto itself the sole right to make the final decision whether there is a defect in materials and or workmanship and whether or not the product is within the warranty This warranty shall not apply to any Aiphone product which has been subject to misuse neglect accident or to use in violation of instructions furnished nor extended to units which have been repaired or altered outside of the factory This warranty does not cover batteries or damage caused by batter
4. 120 ohm rs 120 ohm 120 ohm must be terminated with a 120 ohm resistor at each end at both Ne MK DS A and MK 1MD A Otherwise double up the wires onto each terminal MK DS A MK DS A employs CCD camera and the performance can be affected by l d lt St bright direct light such as strong sunlight gate light or street or porch ae light which comes directly into the camera lens source MK 1MD A Ve vee Mount the video monitor so that the center of the monitor screen comes to MK 1MD A the eye level of the user Mi When camera height is too low PAR MK DS A is equipped with a camera angle adjuster on the back of the unit Pull the lever down to adjust the camera angle upward by 14 a 4 MK DS A BACK VIEW When camera is positioned horizontally When camera angle is upwardly adjusted 4 See 188 cm 6 2 j 3 210 cm 6 11 amera 7 ot 1g center 5 fo em 2 3 alia SS i 75 cm 2 5 Ps aaae 8 8 tegen et ans EE Ft t t VE S sees 1 118 cm 3 10 l a 90 MK DS A i 135 cm 4 5 3 cm 50 cm 20 eo center 1 3 16 X 3 cm a e ee 1 3 16 br ee a 1 i 1 1 i l i l L i 1 100 cm 3 3 iri S777 a E When installing a second station MK 1MD A may have a sub station either the same MK 1MD A monitor or MK 1SD A handset Locate the second station within permitted distance of 100m 330 from the came
5. g PS 18Y into an open AC outlet QM a M PS 18YC A AC 120V PS 18YE AC 220 240V PS 18YC A or PS 18YE Install the power supply within pE 1 9m 6 3 of the monitor Screw 2 e Do not attempt to extend the DC side of the power supply If necessary extend the AC side with an extension cord Bracket ee S wl ela a NP P The SW1 initially set to A position must not be changed except to B ary PS 18YC A or PS 18YE specified position on the first MK 1MD A MK 1MD A Ld a Parallel MK 1MD A or MK 1HD Back View Marks _ BOX 5 Mounting 2 7 bracket EN SINGLE GANG OPERATIONS on MK 1MD A BRIGHT amp TONE chime amp audio controls Speaker for chime amp audio Ss MK 1MD A MONITOR Receiving a door call When call button is pushed on MK DS A it activates 4 tone chime and image at inside monitor s Simply lift handset to reply within 30 seconds Communication The communication is timed for 2 1 2 minutes Press MONITOR button to extend another 2 1 2 minutes Monitor image times out in 30 seconds after called m Audio visual monitoring In standby mode press MONITOR button to activate both audio amp video of door station Audio is heard through open voice speaker Call extension speaker IER 2 allows the chime to be heard at a remote location Volume is adjustable to 3 positio
6. ies used in connection with the product This warranty covers bench repairs only and any repairs must be made at the shop or place designated in writing by Aiphone Aiphone will not be responsible for any costs incurred involving on site service calls 4 A 4 4 4 p 4 4 4 4 4 4 t 4 4 i 4 4 s 4 P k 4 A de 4 y p t 4 4 4 4 PEPEEEEE EEE EEE EEE EEEEEEEELEE EEE EES 4 af oe ofe eje efe efe ofr fe oje ofe efe ole efe efe efe epe efe ofe sfe efe ofe oft ofe oje ofe efe efe oje of fe eje ofe ofe sfe ole efe eje ole ofe efe ole ole eje eje efe oje ole ole eje eje ele ofe sfe ole eje oft of eje oje oje eje ofe ofe of HOME BUSINESS INDUSTRY Printed in Japan E Aiphone Co Ltd Nagoya Japan Aiphone Corporation Bellevue WA USA MK 1MD I E 0597B
7. ns Controls On MK 1MD A MONITOR on front BRIGHT amp TONE chime amp audio volume each 3 positions on left side Second Audio monitor or Audio only station l When MK 1SD A picks up MK 1MD A monitor turns off Pick up either handset MK 1MD A The image remains for 30 sec on the other monitor The second monitor operates exactly the same as main monitor MK 1SD A can be used for door answering and door strike There is no calling between the inside stations ee If someone at hearing the other station is answering or chime Key mark the door hang up handset TONE control chime 25 TECHNICAL PRECAUTIONS Temperature MK 1MD A is rated to operate between temperatures 0 C 40 C 4 32 F 104 F It takes approx one second for system to recycle Image may vary when the Key mark button is held down to activate door strike This is not a malfunction MK 1MD A monitor can work with MY Series door components MY DS MYW CA w MY CA inside and MYW BA long distance adaptor e Image through overhead MYW CA may vary but it is not a malfunction Do not operate MONITOR button and plug in at the same time It will create a continuous high pitched tone and can be reset by momentarily unplugging power supply Cleaning Clean MK 1MD A with a soft cloth dampened with neutral household cleanser Do not use any abrasive cleaner or cloth SPECIFICATIONS
8. ns to dismantle the unit Take the unit to earth ground Do not install MK 1MD A components in any of the following locations as it may cause the system to malfunction High or extreme cold temperature area under direct sunlight near equipment that varies in temperature in front of air conditioner inside a refrigerated area etc Places subject to moisture or humidity extremes Places subject to environmental conditions such as oil dust chemicals salt etc Places subject to constant vibration or impact A GENERAL PRECAUTIONS MK 1MD A equipment except for MK DS A is designed for indoor use only Do not install outdoors MK 1MD A system is not operable during a power failure In areas where broadcasting station antennas are close by intercom system may be affected by radio frequency interference Keep all DC wiring at least 30cm 20 away from AC 100 240V wiring fluorescent lighting or dimmer switches Otherwise cross AC wiring at a 90 angle aE sails SYSTEM OUTLINE amp COMPONENTS MKS 1E DOOR SENTRY is a set with one monitor and one video door station for audio and video door answering and door release A second monitor or audio only handset can be added MK DS A Mi Package contents MKS 1E AC 120V USA or AC 220 240V Boxed set with Main monitor MK 1MD A Door station MK DS A amp Power supply PS 18YC A or PS 18YE e Mounting bracke
9. ra Wire second inside station directly to first inside station e Video impedance matching on SW1 In dual monitor system only change initial A setting to B HIGH position on MK 1MD A main monitor To hear the chime in a remote location install an IER 2 speaker with 2 wires NP from any inside station One IER 2 per station 100m 330 50m 165 E Door strike MK 1MD A monitor provides a dry closure contact for door strike Use Aiphone s EL 9S AC 12V 0 35A powered by AC transformer PT 1210N in USA or a strike appropriate for the door ee ge E Wiring diagrams Single MK 1MD A system Two monitor system MK 1MD A MK DS A MK 1MD A A li MK DS A Video impedance Set to swi GB matching AC trans _ PT 1210N USA j AC trans PT 1210N USA Terminals 1 5 are for MK 1SD A audio station E Video impedance matching NP Non polarized P Polarized _ __ Parallel cable station of 2 monitor system A Do not run door release amp audio video wires in the same jacketed cable MOUNTING MK 1MD A MK 1MD A On back of the unit mounting bracket is attached Mount the bracket to single gang box or wall On the back terminate parallel wires on A1 A2 terminals Connect 18V DC output wires from PS 18Y power supply Red to Black to Mount MK 1MD A monitor onto the bracket aligning at marks Pull down until it firmly locks 5 Plu
10. t e Packet of screws Installation amp Operation Manual Additional wire s for door release gw Components available e Video door station Monitor amp audio stations e Call extension Door strike e Power supply MK DS A MK 1MD A main or sub MK 1SD A PS 18YC A AC 120V 50 60Hz or PS 18YE AC 220 240V 50 60Hz FA Sub audio only station Chime extension AC 12V 0 35A Second room station Either MK 1MD A or MK 1SD A NAMES AND FEATURES MK 1MD A 4 CRT mw Features BRIGHT control vs One door and one monitor system DOORRELEASE amp XPandable with second audio monitor button Key mark or audio only sub station ye Wide angle door station Views 70cm vertically and 100cm horizontally 70 V x 90 H vv Camera angle adjuster on MK DS A Turns up camera angle by 14 TONE control each 3 positions MONITOR butt Speaker for chime tone ution amp audio monitoring WIRING W Cable requirements W Installation location E Call extension e Use a parallel conductor cable Parallel cable Coaxial cable ial cable should not b d Coaxial ca uld not be use s DEA When existing chime wires are used it is possible that the wires may contain AC voltage current Locate and remove the bell YES NO transformer before actually connecting MK DS A Extra wires Extra pair s in the installed cable can affect image quality and
Download Pdf Manuals
Related Search