Aiphone JAW-AZ User's Manual
Contents
1. 2 AIPHONE Video Modulator with Audio Door Station and CCTV Interface INSTRUCTIONS The JAW AZ converts a standard CCTV camera s signal to a 2 wire signal compatible with the JA Open Voice Color Video system This allows the utilization of a color CCTV camera and a separate audio door station JA D to be used in place of a JA video door station Door 2 input only Up to two additional CCTV cameras can be connected to the JA Monitor for video only Adapter 1 amp 2 inputs A motion detector or other activation device can be connected to the Sensor input in place of JA D to trigger the camera Video output is provided for continual viewing and or recording The unit is equipped with a relay output to trigger an external device such as a DVR or video switcher whenever the audio and or video to the Aiphone monitor is on SENSOR RELAY MASTER AUDIO IN NCNC NONO A1 A2 1 2 eo iA SO E L vipeo OFF ON AIPHONE TERMINAL DEFINITIONS AUDIO 1 2 JA D Audio door station input One per system Master Door 2 input only MASTER A1 A2 Output from JAW AZ to JA 2M E CD master input A1 A2 or C1 C2 RELAY NO NO Normally Open relay contact activated when JA monitor is on SENSOR NC NC Normally Closed contact activates unit when tripped by motion detector or other device with N C contacts Requires SET mode to be active on monitor VIDEO IN Composite input signal from CCTV camera VIDEO OUT Composite output to exter2. B2 B2 NOTES 1 JA D is the only audio only door station compatible with this system 2 Video Output is optional If not in use set the 75 ohm switch to the ON position 3 When the SENSOR input is used the camera will turn on when the sensor device is activated NOTE JA D can only be used when JAW AZ is on master Door 2 Input and when JP1 is removed Sensor input requires a Normally Closed contact from 3 party supplied device motion detector etc and cannot be used when JA D is present Pg 2 OPERATIONS Activation of the camera from a Monitor 1 The CCTV camera can be viewed on any of the JA monitors in the system by pressing the MONITOR button repeatedly cycling through each video device in order door 1 door 2 adapter 1 adapter 2 until the desired camera is viewed If the JA D is connected to the JAW AZ they will be on the door 2 input Incoming audio will activate when selected 2 To initiate 2 way audio with the unit press and release the TALK button momentarily Door 1 amp 2 inputs only 3 To turn the monitor off press the MONITOR button again Otherwise it will automatically time out after approximately 30 seconds Activation of a camera by the Audio Door Station 1 When the call button is pressed on the JA D door station the monitor will turn on with the image from the CCTV camera and the chime will sound The monitor will stay on approximately 30 seconds unless answered 2 Pres
3. aster will emit a tremolo alert tone If JA 2MECD is used the picture memory unit will be triggered 4 Disable surveillance mode by toggling the SET button SPECIFICATIONS Power Supplied by JA Monitor Video Input amp Output Composite 1V Peak to Peak NTSC Connector BNC Audio Door input Use JA D surface mount door station only Can only be used on Door 2 input of JA 2MCD JA 2MECD Relay Normally open contact output 24V DC 1A Sensor Normally closed contact input Wire 18AWG 2 conductor non shielded PE insulation solid or stranded Wiring distance Max 330 from JAW AZ to JA 2M E CD Dimensions 1 5 8 H x 7 W x 4 D FCC Class B Verification NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try and correct the interference by one or more of the following measures R
4. eorient or locate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Note Only information pertaining to the connection and operation of the JAW AZ and devices interfacing with it are included here For complete installation wiring and operational information about the JA 2M E CD system please refer to the Installation Manual included with the monitor Aiphone Communication Systems 1700 130th Ave N E Toll Free Technical Support Bellevue WA 98005 1 800 692 0200 Pg 3 425 455 0510 FAX 1 800 832 3765 JAW AZ Instr FAX 425 455 0071 E mail tech serv aiphone com 0306JS
5. nal CCTV monitor switcher DVR video input on another device 75 OHM SWITCH Termination Switch Set to OFF position when VIDEO OUT is connected to CCTV system Set to ON position when video output is not used INTERNAL ADJUSTMENT WHEN JA D AUDIO DOOR STATION IS INCLUDED INSTRUCTIONS 1 Open unit by removing 5 small screws and lifting off cover Locate Jumper labeled JP1 on the right side of the PC board Remove the jumper completely or move it so it is on just one of the posts Replace the cover and the 5 SCrews AR T agi RO E E Pg 1 WIRING DIAGRAM JAW AZ Modulator for Standard CCTV Camera and Audio only Door Station Door 1 JA 2M E CD JA DAC DGC DGV 1 rk A2 JAW AZ MASTER A1 Door 2 AQ JA D CCTV Camera 75 Ohm 1V Peak to peak Independently powered IMPORTANT Do not install JAW AZ JA D on Door 1 input Sensor input cannot be used when JA D is present JA D cannot be used when JAW AZ is connected to C1 C2 inputs CCTV Camera 75 Ohm 1V Peak to peak Independently powered Remote Activation Optional use only when JA D is not installed Adapter 1 When VIDEO OUT is connected set 75 ohm switch to OFF position Constant video output for CCTV monitor DVR etc Normally Open contact for remote device activation i e video switcher DVR etc JA 2HCD JA 2HCD SUB IN B1 B2 SUB OUT B1 SUB IN B1 B2 SUB OUT B1
6. s TALK momentarily to answer speaking hands free Press TALK again to conclude or unit will time out automatically in approximately 1 minute Interfacing Video with Other Systems 1 VIDEO OUT connection simply passes the composite video signal on to a standard CCTV system such as a monitor input on a switcher or DVR This video signal is live as long as the camera is powered When using this feature set the 75 ohm switch to the OFF position 2 SENSOR input allows a motion detector or other activation device to remotely turn on the camera Use any device with a Normally Closed contact If an audio door station JA D is included the sensor input cannot be used 3 RELAY connection provides a Normally Open contact closure that can be connected to an external system This contact will be closed whenever the Aiphone system is turned on This can be wired into a record trigger input on a DVR or any other external device that needs to be notified when the video and audio is activated to the Aiphone monitor Enabling Disabling Surveillance mode 1 If the JAW AZ is connected to the C1 C2 inputs of the JA 2M E CD the SENSOR input will only be active if the master is put into Surveillance mode 2 Toggle the SET button on the JA 2M E CD to enable surveillance mode The SET button will illuminate red and there will be a one minute delay before the sensor input on the JAW AZ becomes active 3 When the sensor contact triggers the m
Download Pdf Manuals
Related Search