3M SCP725 Owner's Manual
Contents
1. image The audio cable is connected to the wrong audio input The audio amplified in the 3M Folding Wall Mount is not connected to a en power supply No audio from speakers The 1 is dark or di e image 1s dark or dim The lamp needs to be replaced 38 desired input source Turn on input source Shorten the cable between the video source and the system or add a video amplifier between the video source and the long cable Adjust Frequency and Phase setting in the Advanced Picture Menu until noise is reduced or eliminated The projector does not have speakers Connect the audio cable to correct input source or change audio video input assignment settings in the projector s Audio menu The I O Module does not supply power for audio The power adapter included with the folding wall mount must be connected to the Audio Power port on the bottom of the I O Module and a cable from the Audio Power port on the top of the I O Module to the power input on the folding wall mount The audio source or the Turn off mute on the speakers are muted audio source The brightness setting is Adjust the brightness too low Green Replace lamp 3M 2011 All Rights Reserved 3M Super Close Projection System SCP725 Operator s Guide Symptom Standby Button State Possible Cause The input source is not Connect an active input active A signal must be source to unit present for the inp2. Super Close Projection System SCP725 Operator s Guide y SN S April 2012 78 6971 1572 9 Copyright O 2011 3M Company All Rights Reserved 3M Super Close Projection System SCP725 Operator s Guide Contents Introduction Thank Yom tor Choosing N IDR deae se rU Te te qot OP bt tI I NEU NIS ee usd eU EC 5 PACE DA OTT Tm 3 DORE 0 met esde 5 Warranty Limited Remedy Limited Lab sr bos oborta detenido Root Eoo 5 Product PAGS US sce a A AE tection etat ui 7 RO INOUCES tn MEUM EUM 7 Safety Information Re a 9 coser eeu MM E N E AE E E A T 12 Contents of Shipping Box ere pe onr Packin MIET A S ocio Aa AN E E NE A E O 13 AVL 450 e E EAEE E E A EEE EEE AE A E E EE EEA EE 13 Product Description Maine C haracte SR A MM eRe eee eee 14 eem 14 Projector Distance from Screen and Image S126 eec ettet i apu e ue etm a PER Uno nbn eR ERR Pe iaa bdanu T agis 15 MEI UE EM MEUM MM EMEN O 15 Pas EUIS AAC INTO PNE 16 Projector Terminal OC CU OMS tears ce pts Ree tme M MRNA MA MM ADAM 16 VO Module Control Panel optional at CeSSODU coenam tun ep 17 Top Terminal VO M Ud 17 Bottom Termina Panel on VO MIO a essa 18 Remote Control Fincas seasea esa r E E EE EEE E 19 Installing Batteries in Remote COR na a ENEE E 20 0 enla 20 Operating Instructions lumen SR 21 Brand Dy MOUC 77 n tUe ebbe 7 Een mad du e
3. on button will light up Clean the projector s air vents as mention the maintenance section The electrical outlet does Connect the projector to not have power an electric outlet that has power You can the test the outlet using another electrical appliance to confirm that it has power The projector s power unit Contact 3M for service has stopped working 36 3M 2011 All Rights Reserved 3M Super Close Projection System SCP725 Operator s Guide Symptom Standby Button State Possible Cause The projector is cooling down Red The lamp has expired The lamp will not ignite There 18 a problem with one of the cooling fans Flashes RED once every second The projector has ambient temperature or Flashes RED twice every attitude or blocked air second sents The projector s processor had a communication error The lamp will not ignite due to electromagnetic or has turned off interference on the communication cable connecting the Control Flashes RED four times port on the projector every second and I O module or poor quality communication cable 3M 2011 All Rights Reserved overheated due to elevated procedure on page 31 Wait until the projector completes its cooling cycle Once the Standby button turns amber you can press the Standby button again Replace the Lamp and press the Standby button to start the projector The lamp ballast may Contact 3M for s
4. 3M If the product is repaired 3M will repair the defective part s with a new or used part s If the 3M Product is replaced 3M will replace the 3M Product with the same or equivalent model and with a new or refurbished 3M Product In the case of an approved warranty claim the replacement 3M Product will carry only the remaining term of the O 3M 2011 AII Rights Reserved 5 Operator s Guide 3M Super Close Projection System SCP725 original 3M Product s warranty period as stated above For warranty service you must provide proof of the date of the original purchase else the manufacturing code date will be used to establish the start date of the warranty The following are exclusions to the above listed warranty a This warranty does not cover 3M Product that is modified or damaged through improper storage misuse abuse accident vandalism improper installation neglect improper shipping damage caused by acts of war disasters such as fire flood and lightning improper electrical current software problems interaction with non 3M products or service other than by a 3M Authorized Service Provider neglect or mishandling by any person Normal wear and tear is not covered under warranty b 3M Product is designed to operate in the typical indoor environment This warranty does not cover 3M Product used outside of the following circumstances e 100V 240V AC 50 60 Hz e Office or similar Environments with low levels of smoke or air
5. DK FE LL Hg LAMP CONTAINS MERCURY Don t throw in trash Dispose according to local state or federal laws See www lamprecycle org or call 1 800 328 1371 3M 2011 All Rights Reserved 3M Super Close Projection System SCP725 Operator s Guide Contents of Shipping Box This projector is shipped with the necessary cables required for standard DVD player PC or laptop computer connections Carefully unpack and verify that you have all of the items shown below If any of these items are missing please contact your place of purchase The shipping carton contains the following items illustrated below If any of these items are missing please contact your place of purchase 1 Projector CHS ha 2 Remote Control Transmitter batteries included i E 3 VGA to VGA cable 1 8m 15 pin Male 2 8 4 Power cord e V 5 Operator s Guide CD 6 USB A B cable 1 8m not shown Note This projector is compatible with two different remote controls Keep Your Packing Materials Save the shipping box and packing materials in the event this product should require shipping to a 3M Service Center for repair Use packing material to protect projector Whats Next Take a few minutes to review the machine characteristics before you setup and operate the projector We hope you will enjoy using this high performance product in your classrooms presentations and training sessions This product has been
6. E co E CPR ICSAC BS SE S EE 0 WAILERS MATS ESL V Warning Read Manual Before replacing Lamp ADVERTENCIA Lea el manual antes de cambiar la l mpara AVIS Lire le manuel avant de remplacer la lampe WARNUNG Lesen Sie im Handbuch nach bevor Sie die Lampe ersetzen AVVERTENZA Leggere il manuale prima di sostituire la lampada SE PVP ARIAT DC RE EA T gt Vo 25 FERRAN Al BE o FA So BRE BU SFR Em i NU Hol ni UE 819 5 7 LAMP REPLACEMENT CAUTION BEFORE REMOVING THE SCREWS DISCONNECT POWER CABLE HOT SURFACE INSIDE ALLOW 1 HOUR TO COOL BEFORE REPLACING THE LAMP HANDLE WITH CARE RISK OF EXPLOSION SEE OWNER 5 MANUAL PRECAUTIONS LORS DU REMPLACEMENT DE LA LAMPE DEBRANCHER LE CABLE D ALIMENTATION AVANT DE RETIRER LES WIS LINTERIEUR DU BOITIEH ETANT EXTREMEMENT CHAUD ATTENDRE 1 HEURE AVANT DE PROCEDEH AU REMPLACEMENT DE LA LAMPE A MANIPULEH AVEC PRECAUTION RISQUE D EXPLOSION SE REPORTER AU MODE D EMPLOI ACHTUNG BEIM LAMPENAUSTAUSCH VOR DEM ENTFERNEN DER SCHRAUBEN DAS NETZKABEL ABTRENNEN HEISSE OBERFLACHEN IM INNEREN BENOTIGEN 1 STUNDE ZUM ABKUHLEN BEVOR DIE LAMPE ERSETZT WERDEN KANN VORSICHT BEIM UMGANG EXPLOSIONSGEFAHR SIEHE BEDIENUNGSANLEITUNG So FP ROHIA Pe TS ESL lt lt 5 CAS 3 lt lt LT gt SLT HEAR HUE C30 c GEL 3 7 AO THE lt lt HH 55 21 U ET RL TE ESL lt SER 55
7. Follow the procedures below 1 Return projector to standby mode After the Standby button turns amber and the fan stops unplug the power cord from the wall outlet 2 When dust or dirt appears on the projector s top surface or around the air vents clean these areas before operating the projector a Wipe the top surface with a clean dry cloth or use a vacuum cleaner b Vacuum the intake air vent while gently tapping on the vent slots to dislodge any dirt c Vacuum the exhaust air vent while gently tapping on the vent slots to dislodge any dirt 3 Plug in the power cord and press the standby button to power on projector Test unit to verify it operates correctly 32 3M 2011 All Rights Reserved 3M Super Close Projection System SCP725 Operator s Guide Cleaning the Lamp Module and Lamp Compartment For best lamp performance there must be adequate air flow through and around the lamp module A build up of dust or dirt will reduce the air flow and shorten lamp life and lamp performance 3M recommends at every lamp change or at least once a year that air vents lamp module and lamp compartment be cleaned with a vacuum Follow the procedure below 1 Unscrew lamp module retaining screws and carefully remove lamp module Important Note Do not touch the glass reflector or the bulb If oils from your skin transfer to the glass it will weaken the heat resistant properties of the reflector bulb and signifi
8. Light 6 Standby On Button 7 Lamp Cover 8 Ventilation Slots 9 HDMI Port 10 Control Input 11 Computer Component Input 12 Slot for Kensington Lock 13 USB Port For remote mouse functionality 14 AC Power Cord Connection 15 Height Adjustment Foot Projector Terminal Connections m TA Ooo o T o I Na Computer I O Module Control Homi O Projector Panel Function A C Power Connect AC power cord to projector 2 USB Connect projector USB B type to computer USB port to control computer pointer with remote control Connect projector control port to computer serial port with RS232 adapter or the 3M I O Module and control the projector SCP725 does not connect audio through the HDMI port 16 3M 2011 All Rights Reserved 3M Super Close Projection System SCP725 Operator s Guide I O Module Control Panel optional accessory If your projector has the optional I O Module installed the projector functions can be operated from the I O Module Control Panel Volume I O Module Control Panel Function ON OFF Turns the projector on and off Increases or decreases audio level gt Switches the displayed input source Switching order Computer 1 gt Computer 2 gt S Video gt Video 4 Meu Displays the projector s menu system 5 Arrow Buttons Navigate up down or left right through projector s Menu system ENTER Select menu item and confirm menu sel
9. born particulates Altitude Humidity 0 4000 ft normal fan speed 5 C 35 C 41 F 95 F 25 to 80 4000 6000 ft high fan speed 5 C 35 C 41 F 95 F non condensing Storage conditions 20 C to 60 C maximum 40 000 ft c The Air Intake and Exhaust Vent must be clear of obstructions including any potential blockage or obstructions caused from a ceiling or other mount Inadequate air ventilation will cause the 3M Product to malfunction or will cause damage to the 3M Product which will void the warranty d This warranty does not cover any additional costs including but not limited to those associated with removal cleaning or installation of the 3M Product adjustments mechanical or electronic made to the 3M Product or replacing customer replaceable parts like lamps and air filters e This warranty covers only normal use of the product 24 hour per day or other excessive continual use causes strain and is not considered normal use f This warranty does not cover consumables e g fuses other than lamps and only as set forth below g This warranty is not transferable h 3M 18 not responsible for warranty service should the 3M label or logo or the rating label or serial number be removed unless otherwise stated in writing for the purpose of private labeling for partnership requirements i This warranty does not cover postage insurance or shipping costs incurred in presenting your 3M Product for warran
10. feature turn On Off and set the PIN code Advanced Setup Input Source Computer 1 PIN Authentication ii Change PIN Network Control Closed Captioning De Magnify Pan Horizontal Pan Vertical NE Super E Close Projection Description Default PIN Authentication Turn the PIN code security feature On or Off Change the 4 digit PIN access code as desired Set PIN code Note When PIN security is enabled the PIN access 3349 code will automatically set to the default value 3349 Turns the network control function on and off The network control feature allows a computer to open the control web page on I O module and control the projector To view the control web page connect the I O Network Control module into the local area network and type the On Off On I O module s IP address into the address bar of a web browser The IP address can be found in the projector s information menu See the next page The control web page will display A RS 232 and network control guide is available at www mmm com meetings in the Technical Documents section Turns on Closed Captioning CC1 CC2 CC3 and CC4 are the different Close Caption channels CCI 1s ce2 cc3 lof the primary channel for most content The content on 4 CC2 CC3 and CC4 may vary on video source Deas Reduces the image size from 100 to 50 of the 50 to 100 projected image size Pan Horizontal Positions the image horizontally Stots O Off CCI
11. produced in accordance with 3M s highest quality and safety standards to provide smooth and trouble free use in the years to come O 3M 2011 AII Rights Reserved 13 Operator s Guide 3M Super Close Projection System SCP725 Product Description The 3M SCP725 integrates short arc lamp and Digital Light Processing DLP technology It accepts input from computer and or video sources and projects a bright image through 3M Vikuiti Super Close Projection technology Machine Characteristics The 3M SCP725 offers the following features e Native Resolution 1024x768 XGA e On screen menu with 9 languages English French Deutsch Spanish Italian Japanese Chinese Traditional Chinese Simplified Korean e Lamp Life of 5000 hours ECO mode e Lamp Life of 3000 hours Bright mode e Image size 30 to 150 diagonal e Aspect Ratio 4 3 e Digital keystone correction e Vertical Lens Shift e RS232 Control capable e 3M Super Close Projection technology Dimensions 4 6 in 116 2 cm EL 2 5 in ES 63 4 cm m 10 2 in n 359 1 cm 1 9 in 5 0 in 47 5 cm 126 6 cm 9 2 6 in 65 1 mm 326 6 cm 53a UN 54 0 mm 0 i 3 3 in 82 639 cm 14 3M 2011 All Rights Reserved 3M Super Close Projection System SCP725 Operator s Guide Projector Distance fr
12. 4 Operator s Guide 3M Super Close Projection System SCP725 42 3M 2011 All Rights Reserved 3M Super Close Projection System SCP725 Operator s Guide O 3M 2011 AII Rights Reserved 43 Important Notice All statements technical information and recommendations related to 3M s products are based on in formation believed to be reliable but the accuracy or completeness is not guaranteed Before using this product you must evaluate it and determine if it 1s suitable for your intended application You assume all risks and liability associated with such use Any statements related to the product which are not con tained in 3M s current publications or any contrary statements contained on your purchase order shall have no force or effect unless expressly set forth in a written agreement signed by an authorized officer of 3M Technical Support Contact http www 3m com meetings e mail meetings mmm com 3M Austin Center 3M Canada 3M Mexico S a deC V 3M Europe Please recycle Building A145 5N 01 P O box 5757 Apartado Postal 14 139 Boulevard de l Oise 6801 River Place Blvd London Ontario Mexico D F 07000 95006 Cerge Pontoise Cedex Litho in USA Austin TX 78726 9000 N6AATI Mexico France 3M 2011
13. Closed Captioning 28 3M 2011 All Rights Reserved 3M Super Close Projection System SCP725 Operator s Guide Information Menu The Information Menu shown below is used to display current projector configuration settings Information Input Source Computer 1 Input Resolution 1024 x 768 H Frequency 31 75 KHz V Frequency 60 Hz A Lamp Hours 1235 System Hours 2356 IP Address 192 168 1 10 Net Mask 255 255 255 0 EN Gateway 192 168 1 1 1 j User Ver 0 0 8 Super EM Close Projection Feature Description Input Resolution Displays the current input Resolution H Frequency Displays the current input H Frequency V Frequency Displays the current input V Frequency Displays the current lamp operating hours for the installed lamp System Hours Hours Displays the current total system time accumulated x rion Displays the current IP Address for the I O module Ethernet interface er dl Displays the current Net Mask for the I O module Ethernet interface x dio Displays the current gateway for the I O module Ethernet interface Displays the current User Version Note This field displays only when the I O Module is connected O 3M 2011 AII Rights Reserved 29 Operator s Guide 3M Super Close Projection System SCP725 Machine Specifications Bright Mode Typical 34 dB A Acoustic Noise Level Normal Mode Typical 32 dB A ECO Mode Typical 28 5 dB A Automatically recognizes the connectio
14. M are registered trademarks of 3M Company Vikuiti is a trademark of 3M Company Digital Light Processing 15 a trademark or registered trademark of Texas Instruments All other trademarks or registered trademarks are property of their respective companies HDMI the HDMI Logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC Important Notice All statements technical information and recommendations related to 3M s products are based on information believed to be reliable but the accuracy or completeness 15 not guaranteed Before using this product you must evaluate it and determine if it is suitable for your intended application You assume all risks and liability associated with such use Any statements related to the product which are not contained in 3M s current publications or any contrary statements contained on your purchase order shall have no force or effect unless expressly set forth in a written agreement signed by an authorized officer of 3M Warranty Limited Remedy Limited Liability This warranty applies to the continental US only The warranty terms conditions remedy and limitation may vary in other countries Contact your local 3M Company for warranty information The 3M SCP700 Series projector the 3M Product is warranted to be free from defects in material or manufacture for a period of three 3 years from the date of purchase or 4 000 hours of usage whichever o
15. age Warning Hazardous Voltage Warning Hot Surface High Temperature Lamp Warning High Pressure Attention Read Accompanying Documentation 3M 2011 All Rights Reserved 9 Operator s Guide 3M Super Close Projection System SCP725 WARNING To reduce the risk associated with hazardous voltage Do not operate this projector in wet environments or outdoors Do not modify this projector or power cord Do not remove any screws other than those specified in the lamp replacement instructions Do not attempt to service the projector other than the lamp cartridge There are no user serviceable parts inside the projector Contact a 3M authorized service provider for service Disconnect power cord when the projector is not in use for extended periods of time during lamp replacement and while cleaning Do not allow water or other liquids to enter the projector To reduce the risk associated with hazardous voltage and or fire Replace power cord if damaged e Contact a 3M authorized service provider 11 the projector becomes damaged Use a grounded extension cord with a rating at least equal to that of the projector Connect this projector to a grounded outlet To reduce the risk associated with choking Keep the battery and battery cover away from children and pets To reduce the risk associated with hazardous voltage impact tripping or intense visible light Do not use this projector around unsupervised childre
16. alance of red to green l 15 15 see note for video signals or softer Video Noise Reduction Turn noise reduction ON or OFF Off Aspectos Set aspect ratio to Full Screen or 16 9 or N A Full Screen Nat ve Navigate to the Advanced picture setting Advanced menu This option is for Computer N A N A Component input and only displays when the I O Module is connected Reset values in this menu only Note Tint Hue can only be adjusted for S Video and RCA video input signals 24 3M 2011 All Rights Reserved 3M Super Close Projection System SCP725 Operator s Guide Advanced Picture Menu The Picture Menu with the Advanced option selected shown below is used to adjust the projected image for Computer and Component inputs only Input Source Computer 1 Over Scan Color Brightness Horizontal Position Vertical Position Frequency Phase 3D Control 3D Reverse Reset Super Close Projection Feature Description Range Adjust cropping of image boundaries from 90th to Video 97 100th percentile increments of 1 percent eu ae VGA 100 Adjust the white peaking value of the DMD a DIOE 0 lowest white peaking value 10 highest value 4 Computer 10 Video 3 10 Horizontal Adjust horizontal position of projected image N A Position Only for Computer I or Computer 2 input source N A Adjust vertical position of projected image Only for Computer I or Computer 2 inpu
17. cantly shorten the lamp s life 3M 2011 All Rights Reserved 33 Operator s Guide 3M Super Close Projection System SCP725 4 Install the lamp taking care to seat it fully into the lamp socket connection and tighten the lamp retaining Screws 6 Verify the projector operates correctly Plug in power cord and press the standby button to power on projector Note If the lamp door ts not installed correctly the projector will not power on 34 3M 2011 All Rights Reserved 3M Super Close Projection System SCP725 Operator s Guide Troubleshooting Identifying an Expired Lamp Module Lamp Module Parts 1 Top of Lamp Module 2 Lamp Connector 3 Air Vents 4 Lamp Wires 5 Bulb Envelope This is the shape of the bulb inside the lamp module Visible Indications of an Expired Lamp The following five visible indicators help you recognize an expired lamp 1 Cloudy Bulb A cloudy bulb may reduce the image brightness The lamp will appear to have white or black deposits on the inside of the bulb These deposits are a sign of normal wear and tear Replace the lamp if the brightness is inadequate 2 Disconnected or broken wires If the lamp wires are broken the lamp will not ignite Replace the lamp if the lamp wires are broken 3 Deformed Bulb A deformed bulb will reduce the image brightness A bulb is deformed when the bulb envelope expands into an irregular round shape Replace the bulb if it becomes
18. ccurs first All other accessories of the 3M Product those in the applicable modular configurations excluding the projector lamps but including the wall mounts ceiling mounts digital annotation sensors and input output devices are warranted to be free from defects in material or manufacture for a period of one 1 year from the date of purchase The lamp component of the 3M Product is warranted to be free from defects in material and manufacture for a period of ninety 90 days after the date of purchase of the 3M Product or 180 hours of lamp usage whichever occurs first This warranty is for parts only and in the case of an approved warranty claim for a lamp your exclusive remedy will be for a replacement product shipped to your location Optional product upgrades and or accessories that are not sold as part of any modular configuration are subject to individual warranties THE WARRANTIES STATED ABOVE ARE EXCLUSIVE AND ARE MADE IN PLACE OF ANY AND ALL WARRANTIES EXPRESS OR IMPLIED WARRANTIES OR CONDITIONS INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY INDUSTRY PRACTICE OR CUSTOM OR TRADE USAGE In the event the 3M Product fails to conform to the above stated warranties within the applicable warranty period your exclusive remedy shall be at 3M s option to replace or repair the 3M Product or to refund the purchase price of the 3M Product All replaced parts or products become property of
19. deformed 4 Debris on Bulb End If the lamp will not ignite the bulb seal may have broken When bulb seal is broken debris from the bulb will form at the break Most of the times this 1s at the bulb tip 5 Broken Bulb The lamp will not ignite if it is broken Sometimes you will hear an abnormal sound when you try to start the projector Please refer to the Safety Instructions for more information about handling broken bulbs O 3M 2011 AII Rights Reserved 35 Operator s Guide 3M Super Close Projection System SCP725 I O Module Troubleshooting Symptom Possible Cause The Standby button on the I O The communication cable is not Connect a communication cable 15 module does not light while the connected or is damaged pin to 15 pin from the projector to projector is powered on the I O module The projector does not have power See projector troubleshooting Projector Troubleshooting Symptom Standby Button State Possible Cause The power cord is not Insert the power cord into connected to projector and electrical outlet an electrical outlet The lamp door is not Make sure the lamp installed or 1s not door is in place and properly fastened down fastened down as shown in the lamp replacement instruction See page 31 The projector has Allow the projector cool overheated and has down Once cooled down automatically shut down the projector will regain The projector will not turn power and the standby
20. directly into the projector lens while the lamp is on To reduce the risk associated with impact of a falling projector e Use only the 3M brand wall ceiling mounting hardware kit if wall or ceiling mounting is desired nstallation of the 3M brand wall ceiling kit must only be performed by qualified personnel Adhere strictly to the proper installation procedure as outlined in the installation instructions when installing the 3M wall ceiling kit When not mounted always operate the unit on a flat and sturdy surface To reduce the risk associated with explosion and or chemicals from leaking battery Use only with battery type AAA Orient the battery s plus and minus terminals according to the markings found on the remote control Do not leave the battery in the remote for an extended period of time Do not heat disassemble short recharge or expose the batteries to fire or high temperature Do not carry batteries loose in your pocket or purse Avoid eye and skin contact in the event that battery would leak Do not mix used and new batteries To reduce the risk associated with tripping and or impact Position the power cord and cables so that they can not be tripped over To reduce the risk associated with environmental contamination Dispose of mercury lamp exhausted batteries and other electronic components in accordance with applicable federal state and local regulations To reduce the risk a
21. ection System SCP725 Operator s Guide Safety Information Please read understand and follow all safety information contained in these instructions prior to the use of this projector Retain these instructions for future reference Intended Use Before operating the machine please read the entire manual thoroughly This product was designed built and tested for use indoors using 3M lamps and hardware The use of other replacement lamps outdoor operation or different voltages has not been tested and could damage the projector or peripheral equipment and or create a potentially unsafe operating condition This projector is designed to operate in a normal office classroom environment Altitude Humidity 0 4000 ft normal fan speed 5 C 35 C 41 F 95 F 25 to 80 4000 6000 ft high fan speed 5 C 35 C 41 F 95 F non condensing The ambient operating environment should be free of airborne smoke grease oil and other contaminants that can affect the operation or performance of the projector Use of this product in adverse conditions will void the product warranty Explanation of Signal Words and Symbols in Safety Labels and Instructions WARNING Indicates a potentially hazardous situation which if not avoided could result in death or serious injury and or property damage CAUTION Indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury and or property dam
22. ections Center of Arrow buttons Top Terminal Panel on I O Module Use the Top Terminal Panel to connect the projector to the I O Module box USE Control Signal Audio To Projector Out ue 55 El eme 6 1 2 3 4 5 I O Module Top Terminal Panel Function 1 Audio Power Relay Audio power from bottom terminal through to speaker amplifier 2 USB Hub Connect two USB devices like the projector s remote mouse to a single USB port on computer connected to the I O Module s bottom terminal panel CONTROL Connect IO Module to projector I O Module CONTROL terminal Connect I O Module to projector COMPUTER port 5 Audio Out Connect IO Module to external speakers or speakers in 3M Folding Wall Mount FWMSV2 O 3M 2011 AII Rights Reserved 17 Operator s Guide 3M Super Close Projection System SCP725 Bottom Terminal Panel on I O Module Use the Bottom Terminal Panel to connect the I O Module box to the Computer Video source Computer 2 Component 2 El 8 6000 eee O I O Module USE Etharnat Computer 1 Computer Qut S Video Stereo Audio Component 1 Minii Out Bottom Terminal Panel Audio Power Supplies power to 3M Folding Wall Mount speakers from the power supply included with the 3M Folding Wall Mount Computer2 Component2 Input for computer or component video device Serial RS 232 Passes control commands from a computer or control system to the projector Video Input for composite video de
23. ervice have stopped functioning Follow the maintenance procedure on page 31 and try starting the projector again If cleaning does not resolve the problem contact 3M for service Follow the maintenance Unplug the power cord and reconnect and then try again If cleaning does not resolve the problem contact 3M for service Make sure the cable connecting the Control Port on the projector to the I O module does not cross power cables or other communication cables If it does reroute the cables so that they do not cross If the communication cable between the projector and the I O module is longer than 4m 13 ft consider using the 3M I O Module Cable Extender P N 78 6972 0027 3 EI Operator s Guide is not selected 3M Super Close Projection System SCP725 Symptom Standby Button State Possible Cause The desired input source Press the remote control Input button to select a The cables from the input Connect the cable to source are not connected correct input source No image Green The input source is not turned on or not displaying an image e g If a notebook computer the external monitor port is not turned on The video cable adds noise to the signal because it 1s not properly terminated too long or lacks adequate electromagnetic shielding Noise in the image Green Green The projector s Frequency and Phase settings are not Noise in the computer properly set
24. eset values in this menu only NA NA 26 3M 2011 All Rights Reserved 3M Super Close Projection System SCP725 Operator s Guide Setup Menu The Setup Menu shown below is used to configure the basic projector operating parameters Input Source Computer 1 Language Auto Shutoff Minutes Keystone Reset Lamp Hrs Lamp Mode Normal Fan Mode Normal Projection Mode Front Projection Factory Reset All Advanced b D 4 2 2 2 A ARR Reset super Close Projection Description Default Language Select the language for menu displays 1 English 2 French 3 Spanish 4 German 5 Italian 6 Japanese 7 Chinese Traditional 8 Chinese Simplified N A English 9 Korean Auto Shutoff Set the number of idle minutes no input source detected and no commands issued before the projector will 10 Minutes automatically shut off Vertical keystone adjustment 40 40 00 Reset Lamp Hours Reset lamp hour status indicator See Information Menu Lamp Mode Bright Normal ECO Normal High Projection Mode 1 Front Pro ection 2 Rear Projection 3 Front Ceiling N A Front 4 Rear Ceiling Projection Reset all menu items to FACTORY DEFAULT settings Select the Advanced Setup Menu Reset values in this menu only 3M 2011 All Rights Reserved 27 Operator s Guide 3M Super Close Projection System SCP725 Advanced Setup Menu The Advanced Setup Menu shown below is used to initiate the PIN code
25. is device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Instructions to Users This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide a reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Notice This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet appareil num rique de la classe A respecte toutes les exigences du R glement sur le materiel brouilleur du Canada Instructions to Users This equipment complies with the requirements of FCC equipment provided that the following conditions are met The cables may have to be used with the core set to the projector side Use the cables which are included with the projector or specified Note Changes or modifications not expressly approved by the party responsib
26. l Rights Reserved 3M Super Close Projection System SCP725 Operator s Guide Input Menu The Input Menu shown below is used to select the desired computer or video input source to be displayed on the projector Input Source Computer 1 Computer 1 Component 1 Computer 2 Component 2 RCA Video S Video Super Close Projection Description Select the Input source to be displayed on the projector 1 Computer 1 Component 2 Computer 1 default DEBE 2 Computer 2 Component 2 Displays only when I O module is connected 3 RCA Video Composite video 4 S Video 3M 2011 All Rights Reserved 23 Operator s Guide 3M Super Close Projection System SCP725 Picture Menu The Picture Menu shown below is used to adjust the picture settings to display the best possible image Picture Input Source Computer 1 Picture Mode Enhanced Photo Brightness Contrast Color Hue Sharpness Video Noise Reduction Aspect Ratio Full Screen Advanced El Reset Super Close Projection Default Piste ode Select the best mode to optimize the projector image 1 Max Brightness 2 Enhanced Photo VGA Max Brightness 3 Enhanced Video Enhanced Photo 4 Photo Dushtues Adjust brightness low to high of 0 100 50 displayed image Co Adjust the contrast dark to light in the 0 100 50 displayed image Color Adjust the intensity of color in the 50 see note displayed image Hue Adjust the b
27. le for compliance could void the user s authority to operate the equipment 3M 2011 All Rights Reserved 7 Operator s Guide 3M Super Close Projection System SCP725 CE STATEMENT Electromagnetic Compatibility Statement Meets 2004 108 EC Directive Low Voltage Directive Meets 2006 95 EC Directive WEEE STATEMENT The following information is only for EU members States The mark shown to the right is in compliance with Waste Electrical and Electronic Equipment Directive 2002 96 EC WEEE The mark indicates the requirement NOT to dispose the equipment as unsorted municipal waste but use the return and collection systems according to local law RoHS STATEMENT 3M Projection Systems can provide RoHS certification for products meeting the RoHS directive European EU Restriction of Hazardous Substances RoHS Directive 2002 95 EC RoHS compliant means that the product or part does not contain any of the substances in excess of the following maximum concentration values in any homogeneous material unless the substance is in an application that 15 exempt under RoHS as amended a 0 1 by weight for lead mercury hexavalent chromium polybrominated biphenyls or polybrominated diphenyl ethers or b 0 01 by weight for cadmium This information represents 3M s knowledge and belief which may be based on information provided by third party suppliers to 3M 8 3M 2011 All Rights Reserved 3M Super Close Proj
28. n To reduce the risk associated with sharp objects premature lamp failure exposure to mercury e Always handle the fragile lamp module with care Replace the lamp module when the lamp replacement message appears Never replace the lamp module with a previously used lamp module e Remove the projector from the ceiling or wall mount before replacing the lamp To reduce the risk associated with permanent vision impairment Do not allow a child under the age of 8 years to view 3D images 10 3M 2011 All Rights Reserved 3M Super Close Projection System SCP725 Operator s Guide CAUTION To reduce the risk associated with eye strain nausea dizziness headache Take a break every hour for 15 minutes e Do not view 3D images or 3D full motion videos while standing or walking Only use 3D Active Glasses for viewing field sequential 3D projected images View 3D image from at least 2 m 7 feet or greater distance Make sure the right eye and left eye images are properly synchronized using the 3D menu of the projector To reduce the risk associated with falling Do not view 3D images or 3D full motion videos while standing or walking Do not allow anyone with a history of photosensitive diseases like epilepsy to wear 3D glasses or view field sequential 3D projected images Do not wear 3D Active Glasses while walking or standing To reduce the risk associated with intense visible light Avoid looking
29. n of I O module Auto Detect amp Install Automatically saves user adjustments Horizontal Sync 69 kHz Computer Compatibility Rel Humidity 10 80 Conditions for usage environment Altitude 0 2286m 0 6000ft Temperature 10 35C 50 95F 328 94 x 264 0 x 116 43 mm 13 2 x 10 6 x 4 7 inches DMD Native Resolution 1024x768 XGA Manual Adjustment HDMI connector VGA mini D sub 15 pin connector Input Output Terminals Control connector USB A B AC power outlet 100 240V AC 50 60 Hz 4 0A L Lif 3000 hrs at 230W Bright mode an 5000 hrs at 180W ECO mode English French Spanish Deutsch Italian Japanese Chinese Traditional Chinese Simplified Korean Focal Length 8 9 mm 300W normal operation 5W standby mode NTSC M 3 58Mz 4 43 MHz Video Compatibility PAL B D G H LM SECAM Wall Ceiling Mount capability Three screw holes 4 5kg 10 Ibs Note Designs and specifications are subject to change without notice Languages 30 3M 2011 All Rights Reserved 3M Super Close Projection System SCP725 Operator s Guide Maintenance Lamp Replacement Note Refer to the Setup Menu to reset the lamp hour timer after replacing the lamp 3M 2011 All Rights Reserved 31 Operator s Guide 3M Super Close Projection System SCP725 Cleaning the Air Vents For best performance 3M recommends that you periodically dust the projector and vacuum all air vents on the projector
30. nse MEME UEM E 21 3M 2011 All Rights Reserved 3 Operator s Guide 3M Super Close Projection System SCP725 Menu Navigation NS a ae E E eds 22 LEA UE D LIN LS LL AP EEE 25 PP Ee il OT NER Em 24 Advanced P UM VES D ao an 25 OM D E EE A NE 26 E E AS 27 AN ARCS e M a a nt m 28 7 E NEE 29 Machine Specifications Maintenance Lainp ee E Pee en rT eee db 31 Cleon na tie 2f NO an te bateria ss 22 Cleaning the Lamp Module and Lamp 001 33 Troubleshooting Identifying an Expired DampsViIOtul oue ceeeserttmdesder misera petu EcUP LEE 35 VO Module Troubles hoolinp era V MM E E MEE E E MES 36 Prol ee O LL MN NRI ME 36 Projector Iid cator 39 nh TiC O ES Romo 39 Replacement Parts and Accessories Kena E eee ee UNE Md ME 40 Optional Accessories DOLES ON 40 4 3M 2011 All Rights Reserved 3M Super Close Projection System SCP725 Operator s Guide Introduction Thank You for Choosing 3M Equipment This product has been produced in accordance with 3M s quality and safety standards to provide smooth and trouble free use in the years to come For optimum performance please follow the operating instructions carefully We hope you will enjoy using this high performance product in your classroom meetings presentations and training sessions This product is Class A and can not be sold into the home market Trademarks The 3M logo and 3
31. om Screen and Image Size Refer to the chart below for the projector to screen distance and corresponding projected image size values Diagonal Width HeightGD in mm i mm in mm 4 0 2434 238 6 Sun 1 a 36 os ms 3 n 12 165 75 60 45 3708 98 312 91 8 20 80 64 48 3958 1006 334 98 834 219 90 72 54 4412 132 414 110 934 247 100 so 60 4912 1258 43 4 122 1034 274 150 120 90 7414 1886 71 4 183 1614 4l Vertical Lens Shift The lens shift feature will vertically offset the picture from 1 in 30 mm up to 4 in 117 mm depending on the projector to screen distance and size of the projected image This adjustment is typically used with wall mount applications as a fine adjustment to the vertical position of the projected image Turn the adjustment screw to vertically raise or lower the physical position of the lens Refer to the chart above for the offset values Note The Lens Shift adjustment screw does not adjust or change any keystone properties O 3M 2011 AII Rights Reserved 15 Operator s Guide 3M Super Close Projection System SCP725 Parts Identification Super Close Projection Lens Focus Adjustment Lens shift Remote Control IR Sensor 1 2 3 4 5 Status Indicator
32. requires service 3M will ask you to bring or send the 3M Product securely packaged in its original container or equivalent along with proof of the date of original purchase to your 3M Service Dealer or 3M Service Center 3M will at its option repair or replace the defective unit without charge for parts or labor Return of the 3M Product will be at 3M s expense e When warranty service involves the exchange of the 3M Product or of a part the item replaced becomes 3M property e The exchanged 3M Product or part may be new or previously refurbished to the 3M standard of quality and at 3M s option the replacement may be another model of like kind and quality e 3M 5 liability for replacement of the warranted 3M Product or part will not exceed the original retail selling price of the 3M Product Exchange or replacement products or parts assume the remaining warranty period of the product covered by this limited warranty However each replacement lamp carries the limited 90 day watranty stated above Product Patents This product is covered by one or more of the following patents U S Patent Number D555 184 U S Patent Number 7 123 426 U S Patent Number 7 126 767 U S Patent Number 7 271 964 Regulatory Notices Video signal cables Only use cables delivered by the manufacturer FCC STATEMENT CLASS A This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 th
33. s displayed on the screen then pull the TRIGGER button to initiate that option or setting To exit an on screen submenu press the MENU button Main Menu The main menu is the first system menu to display when the MENU button is pressed Click on the menu icons to display the desired submenu Main Menu T ceed x 0 X ges Super EM Close Projection Menu Description Input Menu Select the desired computer or video input source Picture Menu Adjust the following picture features mode brightness contrast color intensity tint sharpness video noise reduction aspect ratio and menu reset Note Displays only when input source is connected We Advanced Picture Menu Adjust the following settings for the detected signal source over scan brightness color horizontal position vertical position frequency phase amp menu reset 1 Advanced Audio Menu Adjust the following audio settings volume mute audio input stereo mini 1 stereo mini 2 RCA menu reset Setup Menu Select or adjust the following settings menu languages auto shutoff timer keystone lamp hours lamp mode fan mode projection mode factory reset PIN code and menu reset Information Menu Display the current system information input resolution H V frequency lamp hours system hours IP address net mask gateway for I O module Ethernet interface user revision 22 3M 2011 Al
34. site Video gt S Video lt HDMI Press to increase speaker volume Press to decrease speaker volume Press to switch the audio sound ON or OFF to exit menu top remote only connected to projector USB connected to projector USB Moves cursor left through menu items Moves ppt slides Left Arrow 5 PP backwards Right Arrow Moves cursor to right through menu items Moves ppt slides forward Allows remote mouse functions Allows Pan function when Mouse Pad in Zoom mode Blank Press to replace projected image with black image Press again to return projection image Press to temporarily freeze movement on current image in Freeze motion Press again to return to active image Note This function is intended for a few minutes only Press to initiate a 10 00 minute digital timer Press up down arrows to change timer clock by 1 minute intervals up to 99 00 Press and hold to increase the size of the displayed image up Zoom to 200 percent TOON Press and hold to decrease size of the displayed image down to 100 percent Trigger Button Pull trigger for remote LEFT mouse button functions In bottom remote only menu mode use for remote Enter Select functions Trigger button on J backside of remote 3M 2011 All Rights Reserved 19 Operator s Guide 3M Super Close Projection System SCP725 Installing Batteries in Remote Control 1 Push down on cover to unlatch it Slide cover off 2 Ins
35. ssociated with lamp rupture related hazards n event of lamp rupture call 3M authorized service provider for repair Ruptured lamp repair 1s not user serviceable Wash your hands thoroughly if contact with ruptured lamp debris has taken place Ventilate the area where the lamp rupture occurs The lamp operates at high temperature To reduce the risk associated with hot surface of lamp cartridge Before replacing the lamp allow the lamp to cool for 60 minutes and then unplug the projector from the electrical outlet To reduce the risk associated with environmental contamination due to mercury Hg Lamp contains mercury Don t throw in trash Dispose according to local state or federal laws See www lamprecycle org or call 1 800 328 1371 SAVE THESE INSTRUCTIONS O 3M 2011 AII Rights Reserved 11 Operator s Guide 3M Super Close Projection System SCP725 Safety Labels The following safety labels are used on this product AYRES AY WARNING BEFORE OPERATING PLEASE READ OWNER S MANUAL DO NOT REMOVE SCREWS EXCEPT LAMP COVER SCREWS DO NOT BLOCK VENTING OPENINGS AVIS VEUILLEZ LIRE LE MODE D EMPLOI AVANT L USAGE NE PAS RETIRER LES VIS A L EXCEPTION DES VIS DU COUVERCLE DE LAMPE NE BOUCHEZ PAS LES ORIFICES DE VENTILATION WARNUNG VOR DEM EINSATZ DIE BEDIENUNGSANLEITUNG LESEN KEINE SCHRAUBEN AUSSER DEN LAMPENDECKELSCHRAUBEN ENTFERNEN LUFT NGSOFFNUNGEN NICHT BLOCKIEREN S
36. t source Adjust the horizontal width of the projected image 50 Only for Computer I or Computer 2 input source dau Adjust clock phase to reduce image distortion 15 Only for Computer I or Computer 2 input source ie 09 Turns on or off TI 3D DLP Link On reverts to Off On Oft 3D Control but Always On is not affected when the projector is N A Always On removed from its power source Turn on 3D Reverse 3D Reverse flips the order of the left and right image for the eyes in the event they are out of sync The left and right image are out of 3D Reverse sync when the images in the background appear closer than the image 1s the foreground On reverts to Off but Always On is not affected when the projector is removed from its power source Reset values in this menu only On Off Always On 3M 2011 All Rights Reserved 25 Operator s Guide 3M Super Close Projection System SCP725 Audio Menu Menu displays only if I O Module is connected The Audio Menu shown below is used to adjust the audio settings and select the audio input source to play through the projector Input Source Computer 1 Volume Mute Audio Input Y Stereo Mini 1 Stereo Mini 2 RCA Super Close Projection Adjust volume level 0 muted 20 full volume 7 7 Turn mute mode ON and OFF Select the audio input source to process Audio Input Stereo Mini 1 VGA Component Stereo Mini 2 VGA2 Component RCA S Video Component R
37. tall same type of batteries with the correct polarities 3 Reinstall battery cover Note Verify the battery cover is fully latched before using the remote control Setup and System Configuration 100 240 VAC 50 60 Hz t a 00 0 73 Service Computer mponent Optional Accessory 78 6969 9937 0 Audio uter 2 Stereo Power Component 2 Serial RS Video R Mini 2 oto 2 N RCA Audio ALP p ll coum cue O OS 9 USB Ethernet Computer 1 Computer Out S Video L Stero Audio Component 1 Mini Out Elm 322 0E l Computer 2 Component 2 Stereo Audio Minil Out 20 3M 2011 All Rights Reserved 3M Super Close Projection System SCP725 Operator s Guide Operating Instructions Projector Start Up Read the Important Safeguards before operating the SCP725 After all cable connections have been completed refer to Setup and Configuration the projector can be powered up For best results please observe the following start up sequence l Power ON all of the connected equipment 2 Plug the supplied power cord into the AC inlet of the projector 3 Press the On Standby button on the projector or remote control The lamp will turn on and an image will appear and grow brighter on the screen 4 If the security feature is activated enter the 4 digit PIN code a Press the left right arrow to move the cursor thro
38. ty service Said costs are the customer s responsibility If a claimed defect cannot be identified or reproduced in service the customer may be held responsible for cost incurred Should your warranty upgrade include a change out service and the claimed defect cannot be identified or reproduced by the technician the customer will be responsible for call out costs FAILURE TO FOLLOW THE INSTRUCTIONS CONTAINED IN THE APPROPRIATE 3M PRODUCT MANUAL OR FAILURE TO USE THE 3M PRODUCT IN ACCORDANCE WITH 3M S INTENDED USE STATEMENT WILL VOID ALL WARRANTIES AND LIMITED REMEDIES EXCEPT AS SPECIFICALLY STATED IN THE APPLICABLE 3M PRODUCT MANUAL 3M SHALL NOT BE LIABLE FOR ANY INDIRECT INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO LOSS OF PROFITS REVENUE OR BUSINESS RESULTING FROM OR IN ANY WAY RELATED TO PERFORMANCE USE OR INABILITY TO USE ANY OF THE 3M PRODUCT This limitation applies regardless of the legal theory upon which damages are sought For warranty support please call or write your local 3M office or a 3M Authorized Service Provider to obtain RMA Return Material Authorization Number before returning the product If you are inside the Continental United States of America please contact 3M Customer Service at 800 328 1371 or email meetings mmm com 6 3M 2011 All Rights Reserved 3M Super Close Projection System SCP725 Operator s Guide What 3M Will Do To Correct Problems e If your 3M Product
39. ugh each PIN field b Press the up down arrows to change the value in each field NH EE c Press the Trigger button on the remote to enter the PIN access code 5 Check all ventilation slots and clear away any obstructions 6 Extend or retract front adjustment foot to obtain best image height Note Rotate foot for fine adjustment TE d Turn the focus adjustment top of projector to obtain the best image sharpness Stand By Mode When an image is not being projected place the unit into standby mode l Press the On Standby button on the Remote Control or the On Off button on the I O Box When the message Press the power button to turn the unit off displays press the On Standby button again 2 The lamp will switch off and the power button will first turn red indicating the unit is in lockout and then after 90 seconds the button turns amber to indicate the unit is in standby mode Note In standby mode the cooling fans will continue to run for 5 minutes and then turn off 3M 2011 All Rights Reserved 21 Operator s Guide 3M Super Close Projection System SCP725 Menu Navigation To display the on screen menus press the MENU button on the remote control or I O Module Use the remote control Up Down ARROW buttons to select the desired menu see table below then pull the TRIGGER button bottom of remote control to display it Use the remote control ARROW buttons within a submenu to select the various option
40. ut to be Desired input source selected cannot be detected The input device e g Turn on input source computer DVD player etc is not turned on The remote control is not Face the remote control facing the remote control toward the remote control sensor sensor The remote control is too Operate the remote far from the sensor control within 5 meters An obstruction is between Remove obstacle the remote control and the sensor The remote control does not work The remote control s Correctly insert batteries batteries are exhausted or inserted wrong Projector Indicator Lights Red LED Four EIS every second I O Module Indicator Lights Indicator Signals on I O Model Box Stand by Orange LED always ON Normal Operations Green LED always ON Cooling Lock Out Red LED Solid light O 3M 2011 AII Rights Reserved 39 Operator s Guide 3M Super Close Projection System SCP725 Replacement Parts and Accessories Replacement Parts 3M Part Number VGA Cable 1 8 m 78 8 134 7029 7 78 8134 7200 4 SCP725 SCP725W Lamp Replacement 78 6969 9996 6 Optional Accessories not shown 3M VO Module V3 USB Cable 3 5 m 11 5 ft 78 8134 7219 4 Control Cable 15 pin DB 3 5 m 11 5 ft 78 8134 7220 2 VGA Cable 3 5 m 11 5 ft 78 8134 7218 6 40 3M 2011 All Rights Reserved 3M Super Close Projection System SCP725 Operator s Guide O 3M 2011 AII Rights Reserved
41. vices RCA Input R L Right and Left Channel Audio Input Stereo Mini 2 Stereo Audio input for Computer2 USB Connects the two devices connected to the top terminal panel USB ports to a computer Ethernet Allow access to the projector control webpage and control command over a network remote monitoring amp control 9 Computerl Component Input for computer or component video device Computer Out Output the signal from the Computer 1 port S Video Video device input for S video Stereo Mini 1 Stereo Audio input Audio Out Connects selected audio input to active speakers or audio amplifier 18 3M 2011 All Rights Reserved 3M Super Close Projection System SCP725 Operator s Guide Remote Control Functions Use a USB cable to connect from the PC to the SCP725 or SCP I O Module if equipped and aim the remote control toward the projection screen or at the IR sensor on the projector Press desired remote control button to send a signal to the projector Note This projector is compatible with two remote control transmitters ON STANDBY ON Press to turn projector ON OFF Press to display confirmation message press again to switch projector to Standby mode Note The confirmation message displays to ensure unit does not get turned off accidentally INPUT SOURCE Press for current input source Press again to select different computer video input Computer 1 Component 1 Computer 2 Component 2 RCA Compo
Download Pdf Manuals
Related Search