Home

3M MP7630B Owner's Manual

1. Shipping Box Contents The 3M MP7630B MP7730B Personal Projector is shipped with the necessary cables required for standard VCR PC Macintosh or laptop computer connections Carefully unpack and verify that you have all of the items shown below If any of these items are missing please contact your place of purchase Re en RA ut h MP7630B MP7730B Remote Control 2 Prong Mac Power Cords VGA Personal Projector Transmitter Adapter with Adapter US UK Europe Cable Ground General PS 2 Serial ADB Mouse Adapter Cable Mouse Adapter Cable Soft side Carrying Case S Operator s Guide Quick Start Product Safety Product Registration Lens Cover Batteries CD ROM Guide Guide Card Optional Accessories Video Module RCA with tuner 1 Video Module SCART without tuner 1 Y Note For more information on the Optional Video Module and its functions please see the Optional Video Module section of this manual Y Note Save the shipping box and packing materials in the event the MP7630B MP7730B should require shipping to a 3M Service Center for repair What s Next After you have unpacked the MP7630B MP7730B and identified all the parts you are ready to set up the projector Please read this guide thoroughly before operating your new projector Be sure to check our web site www 3m com meetings regularly for updates and supplemental information On the C
2. 8 0 ft 10 0 ft 134 7 cm 101 0 cm 168 4 cm 3 1m 40m 53 in 40 in 66 3 in 10 0 ft 13 0 ft 200 2 cm 150 1 cm 250 2 cm 46m 6 0m 79 in 59 in 98 5 in 15 0 ft 20 0 ft 265 6 cm 199 2 cm 332 0 cm 6 1m 8 0m a 105 in 78 in 130 7 in 20 0 ft 26 0 ft lt gt 331 0 cm 248 3 cm 413 8 cm 7 7m 10 0 cm 130 in 98 in 162 9 in 25 0 ft 33 0 ft 399 5 cm 299 6 cm 499 4 cm 9 3m 12 0m 157 in 118 in 196 6 cm 30 0 ft 39 0 ft Note These sizes are 1 This is due to variations in the manufacture of the lens If you are close to one of the endpoints you should verify with your unit that the image is the proper size at the proper distance For your own customized screen chart please click here on the CD ROM or visit our Projector to Screen Calculator on the 3M web site www 3m com meetings screen 7630_calc html Digital Keystone Correction Keystoning is when the projected image is noticeably wider on either the top or bottom There are two ways to correct this 1 Press Menu on the remote control or projector then select the Display menu first menu bar button on the left then adjust the sliding bar labeled Keystone as needed 2 Use the Keystone buttons on the external control pad Pressing the button will correct keystoning at the top of the image Pressing the button will correct keystoning at the bottom of the image Brighiress a 2 Contrast AS
3. Color Balance a 1 or KEYSTONE 3M IPC 2001 3M Personal Projector MP7630B MP7730B System Setup Connecting to Various Equipment It only takes a few minutes to connect the 3M Personal Projector MP7630B MP7730B to your computer VCR or other device Connection Terminals SERIAL S aN PS 2 N a E ono ADB MOUSE VIDEO y Cable NS J DO Y PC be or General Mac Cable Power 3M Personal Projector MP7630B MP7730B O 3M IPC 2001 System Setup Mouse Connection The general cable links the projector to the proper mouse adapter cable for your computer s Sy Attach the male Mini DIN end of the general cable to the E K 1 General cable Mouse port on the rear of the projector E SER Attach the female Mini DIN end of the general cable to the end of the proper mouse adapter cable for your computer serial PS 2 or ADB cable Line up the arrows on the sides of the plugs before attaching Be sure not to bend or break the small metal pins inside the plugs Attach the other end of the mouse adapter cable to the proper port on your computer serial PS 2 or ADB Female Mini DIN Male Mini DIN Apple Desktop Mouse The Macintosh operating system should recognize the MP7630B MP7730B as
4. Ky o ON DRAG CJ x 2 Ss So RY A q w A x o RETURN MUTE own CHUP REVERS D DD ERASE SCAN Add Erase Add favorite channels Erase channels which were previously added Laser Press button to turn on the Laser Pointer Exit Press button to exit menu screens Menu Selection Arrows Press buttons to change between the four menus Blank Press button to turn the screen blanking function ON OFF Disk Pad Operate for normal mouse functions Mouse Mode to select function Menu Mode R Click Press for right mouse button function Mouse Mode Volume Press to increase or to decrease speaker volume Mute Press button to turn the mute function speaker sound ON OFF Reverse Press to go back to previous channel Scan Scans channels which have good reception Note These features are for use only with the optional video module E 3M Personal Projector MP7630B MP7730B 3M IPC 2001 Introduction Remote Control Features The remote control sensor is located near the back of the projector The distance between the sensor and the remote control unit must be shorter than 4 meters 13 feet Freeze The image will be frozen when the Freeze button is pressed A Pause icon appears at the lower right of the screen for three seconds during the freeze function A Play icon appears at the lower right of the screen for three sec
5. a mouse without any drivers being loaded VirtualMouse for PC Computer TM For IBM compatible computers set the operating systems to Serial Mouse or PS 2 Mouse to recognize projec tor as the mouse pointer device To set mouse driver information a Windows 95 Windows 98 Windows NT Select Start Settings Control Panel Select Add New Hardware Windows will now search for any PnP devices Click Next Hardware Types Scroll down to Mouse Click Mouse Select Manufacturer Standard Mouse Type Select Model Standard Serial Mouse Click Next Finish Start Restart Windows if prompted Bee ON eas oe ee b Windows 3 1 From Program Manager 1 Click Main 2 Click Windows Setup make note of the current mouse driver 3 Click Options 4 Then Change Systems Settings 5 Choose Mouse 6 It should be listed as Microsoft or IBM PS 2 Note For proper mouse operation always turn the projector power on first and power up the computer For some laptop computers you may need to disable the internal pointing device IPD This is done through the BIOS level set up of the particular machine or it could be listed in a Utilities TM 99 program group i e Toshiba Utilities or Thinkpad Features 3M IPC 2001 3M Personal Projector MP7630B MP7730B EH Startup O Ground lead O oo eq Power Note Make all cable connections and line h
6. attached When the LED blinks rapidly it indicates that the lamp is not attached properly Temperature is too high When the projector s internal temperature is too hot to operate safely the LED blinks slowly for one minute and the lamp goes off automatically If the LED light is off it means that the projector s lamp and temperature are operating under normal conditions 3M IPC 2001 3M Personal Projector MP7630B MP7730B EJ Maintenance Lamp Replacement To reduce the risk of electrical shock always turn off projector and disconnect A WARNING a de power cord before changing lamp 1 Turn the main power switch off and disconnect the power cord from the outlet 2 Loosen screw and remove the lamp cover If the lamp is hot avoid burns by waiting 45 minutes until lamp has cooled 3 Loosen two screws designated by arrows below It is strongly recommended to use a magnetic headed screwdriver 1f possible Pull the handle to remove lamp housing If the screws are not loosened completely they could damage your fingers Do not insert your hand into the box after the lamp is removed If the optical parts inside are touched by hand it could cause color unevenness etc 4 Replace the lamp with the new one insert into projector and tighten the screws Firmly tighten the lamp screws Loose screws may cause a bad connection which may result in a malfunction 5 Re install the lamp cover and tighten the screw Do
7. hot parts 36 Position the cord so that it will not be tripped over pulled or placed in contact with hot surfaces 7 If an extension cord is necessary a cord with a current rating at least equal to that of the appliance should be used Cords rated for less amperage than the appliance may overheat 8 Always unplug appliance from electrical outlet before cleaning and servicing and when not in use Grasp plug and pull to disconnect 9 To reduce the risk of electric shock do not immerse this appliance in water or other liquids 10 To reduce the risk of electric shock do not disassemble this appliance Take it to a qualified technician when service or repair work is required Incorrect reassembly can cause electric shock when the appliance is subsequently used 11 Connect this appliance to a grounded outlet 12 Do not expose this projector to direct sunlight or use it outside 313 Keep all ventilation openings free of any obstructions 14 Always open the lens shutter or remove the lens cap when the projector lamp is on 15 Do not look directly into light beam of laser pointer The pointer produces a strong light which could damage your eyesight 16 The projection lamp contains mercury Always dispose of it in a proper manner according to local regulations 17 Always operate machine on a flat sturdy surface E 3M Personal Projector MP7630B MP7730B 3M IPC 2001 Introduction Product Safety Labels The followin
8. not turn on the power with lamp cover removed Whenever the lamp has been replaced reset the total operation time of the lamp Do not reset if the lamp was not replaced as this could cause breakage Y Note For maximum lamp life do not shock handle or scratch the lamp glass when it is hot Also do not use an old or previously used lamp as a replacement lamp EJ 3M Personal Projector MP7630B MP7730B 3M IPC 2001 Maintenance Lamp Ordering When ordering a lamp use the part number that references the projector model number Note To determine projector model number look at the bottom cover label only 3M Visual Systems Division Austin TX 78726 9000 PROJECTOR MODEL NO MPXXXX 100 240V 50 60Hz 3A Mfg Date M Tested To Comply With FCC Standards FOR HOME OR OFFICE USE including inte at may cause undesired operation N214 Serial No 99J0777TOAYWWXXY Revision XXX Projector Model Number Lamp Part Number MP7630 MP7730 78 6969 9036 1 MP7630B MP7730B 78 6969 9297 9 3M IPC 2001 3M Personal Projector MP7630B MP7730B EJ Maintenance Resetting the Lamp Hours Please do the following within 10 minutes from turning power on if you replace the lamp after 1500 hours 1 Press the Menu button and use Keystone buttons to select the Control sub menu Then press the Menu butto
9. of the 3M product Limitation of Liability Except where prohibited by law 3M will not be liable for any loss or damage arising from this 3M product whether direct indirect special incidental or consequential regardless of the legal theory asserted Let us help you make the most of your next presentation We offer everything from presentation supplies to tips for better meetings And we re the only transparency manufacturer that offers a recycling program for your used transparencies For late breaking news handy reference and free product samples call us toll free in the continental United States and Canada 24 hours a day or visit our Internet Website http 3m com meetings 800 328 1371 E male te mic 3M Austin Center 3M Canada 3M Mexico S A de C V 3M Europe Building A145 5N 01 P O Box 5757 Apartado Postal 14 139 Boulevard de 1 Oise Litho in USA 6801 River Place Blvd London Ontario Mexico D F 07000 95006 Cerge Pontoise Cedex Copyright O 2001 3M IPC Austin TX 78726 9000 N6A 4T1 Mexico France All Rights Reserved 78 6970 9063 3 Rev A
10. sub menu Select the Tuner items and press the Keystone keys to prompt out of the tuner menu Source EH PC E Video HE S Video M Tuner Volume Treble Bass Mute im Off E On Tuner Press lt or gt to select 2 Use the Menu button on the control pad or remote control unit to scroll through the Tuner sub menu e TV CATV Please select the TV signal source If the source is from CATV please choose CATV Otherwise select TV e Nationality Please select the corresponding number representing the user s country See reference chart Y Note The item NONE Tuner is only for the user s information and is not a function For example if current A Box is NTSC Tuner box then NTSC Tuner will appear in this section NONE Tuner TV CATV Nationality 1 m2 m3 m4 m5 m6 m7 m8 m9 EJ 3M Personal Projector MP7630B MP7730B 3M IPC 2001 Optional Video Module 3 After leaving the menu system press the Scan button to scan all existing channels in that region Y Note Scan function must be done for the first use in certain regions to catch all the channels in the local CATV system START SCANNING Yes No After the START SCANNING dialog box prompt use the Channel Up Down buttons to select Yes or No Press Return button to set Function Must be performed with remote co
11. D ROM you can link directly to the web site by clicking here or on 3M Innovation in the lower right corner of the Main Menu O 3M IPC 2001 3M Personal Projector MP7630B MP7730B Ed Introduction Part Identification 1 Standby On Button 8 Projection Lens 2 External Control Pad see next page 9 Height Adjustment Foot 3 Remote Control Sensor 10 AC Power Cord Input 4 Carrying Handle 11 Serial Port Terminal Connection 5 Image Tilt Control 12 Mouse Control Port Serial PS 2 e ADB 6 Kensington Lock Slot 13 Remote Control Transmitter 7 Lamp Access Door underneath unit 14 Video Module Connection E 3M Personal Projector MP7630B MP7730B 3M IPC 2001 Introduction Machine Characteristics The MP7630B MP7730B Personal Projector integrates ultra high bright lamp and TI DLP technology into a single unit The MP7630B MP7730B Personal Projector offers the following features e Small and portable unit e Ability to display 16 7 million colors e Easy to set up and use e Full function remote control e SVGA resolution and component video compatible e Digital keystone correction MP7730B XGA resolution e IR remote control sensor on top Horizontal and vertical image inverting e On screen menus in seven languages e Horizontal and vertical image position control e Color balance control for data video e Ultra high brightness pr
12. JORDAT UTTAG N R DEN ANSLUTS TILL ETT N TVERK Made in Fabrique au Hecho en Taiwan Save These Instructions The information contained in this manual will help you operate and maintain your 3M MP7630B MP7730B Personal Projector O 3M IPC 2001 3M Personal Projector MP7630B MP7730B El Introduction Thank You for Choosing 3M Thank you for choosing 3M multimedia projection equipment This product has been produced in accordance with 3M s highest quality and safety standards to ensure smooth and troublefree use in the years to come For optimum performance please follow the operating instructions carefully We hope you will enjoy using this high performance product in your meetings presentations and training sessions Warranty Limited Warranty 3M warrants this product against any defects in material and workmanship under normal usage and storage for a period of two years from date of purchase Exclusion to Warranty The lamps are considered a consumable item and are warrantied for 90 days or 180 hours whichever occurs first Proof of purchase date will be required with any warranty claim In the event this product is found to be defective within the warranty period 3M s only obligation and your exclusive remedy shall be replacement of any defective parts labor included To obtain warranty service immediately notify the dealer from which you purchased the product of any defects In the USA call 1 800 328 1371 for wa
13. MP7630B MP7730B Personal Projector Operator s Guide MP7630B MP7730B Projecteur personnel Guide de l op rateur MP7630B MP7730B Personal Projektor Benutzerhandbuch MP7630B MP7730B Gu a del Usuario del Proyector Personal MP7630B MP7730B Guida dell operatore per il Proiettore personale MP7630B MP7730B Bruksanvisning f r Personlig projektor MP7630B MP7730B Personal Projector Gebruiksaanwijzing Table of Contents On the CD ROM please click on any section to jump to that section Introduction SAUS aa 4 Thank You for Choosing SM ita 6 A OO 6 Shipping Box Contents aiii ES 7 Optional Accessories ivi rennes 7 A a EE ee nrnna 8 Machine Characteristics aaa 9 Remote Control Identification 10 Remote Control Features aa 11 System Setup SCSI GS LE RE E REED RENDER PRN nents DR caida 13 Digital Keystone Corrections 13 Connecting to Various Equipment 14 Mouse Connection iaa 15 Operation Start Up ns a Mase 16 SSUTOOW q DAR iia 17 A A eat ead a a 18 Optional Video Module ss nue Men ses 23 Attaching the Optional Audio Visual Module 24 Optional Video Module Menus occcccnooccccccnocccccnnonnnnnnncnnnancnnnnnn 25 Maintenance E SUB EE Te iia A dae eee a Ee Me Ee ees eae ee 29 Lamp Replace ducati 30 Resetting Lamp Hours 225auu8 entente ee 32 Troubleshooting Common Problems amp Solutions oooocconnncccccnonacccccnnonanacccnnanancncns 33 S
14. UIRE LA LAMPADA SPEGNERE IL PROIETTORE ED ESTRARRE LA SPINA DEL CAVO DI ALIMENTAZIONE DALLA PRESA DELLA RETE ELETTRICA PRIMA DI SOSTITUIRE LA LAMPADA ASPETTARE CHE SI RAFFREDDI ALMENO 45 MINUTI A TOCCARE LA LAMPADA QUANDO E CALDA SI CORRE IL RISCHIO DI SCOTTARSI LA MANO CONSULTARE LE ISTRUZIONI PER L USO ALTO VOLTAJE ALTA TEMPERATURA ALTA PRESION PARA REEMPLAZAR LA L MPARA APAGUE EL PROYECTOR Y RETIRE EL CABLE DE ALIMENTACION DEL TOMACORRIENTE ANTES DE REEMPLAZAR LA L MPARA ESPERE HASTA QUE LA L MPARA SE ENFRIE ALMENOS 45 MINUTOS SITOCA LA L MPARA CUANDO EST CALIENTE PUEDE QUEMARLE LAS MANOS LA L MPARA ES ALTA PRESION CUANDO ESTA CALIENTE PUEDE EXPLOTAR SI NO ES MANIPULADA DEBIDAMENTE CONSULTE LA GU A DEL USUARIO WARNING AVERTISSEMENT VORSICHT PRECAUCION RISK OF ELECTRIC SHOCK DO NOT OPEN REFER SERVICING TO QUALIFIED SERVICE PERSONNEL POUR PR VENTIR DE TOUT CHOC LECTRIQUE NE PAS OUVRIR L APPAREIL AUCUNE PI CE INTERNE N EST CHANGEABLE PAR L UTILISATEUR POUR LA MAINTENANCE SE REFERER AU PERSONNEL QUALIFI GEFAHR DES ELEKTRASCHEN SCHLAGES R CKWAND NICHT ENTFEREN WENDEN SIE SICH AN SERVICE FACHPERSONAL PARA PREVENTIR DESCARGAS ELECTRICAS NO ABRIR LA TAPA NI MANIPULAR EN SU INTERIOR SI NO ES POR PERSONAL CUALIFICADO Apparatet m kun tilkoples jordef stikkontakt Laite on liitett v suojakesketimpistorasiaan jos se on liitetty lanjaan johdinverkoon APPARATEN SKALL ANSLUTAS TILL
15. al Projector MP7630B MP7730B 3M IPC 2001 Operation Shutdown Standby On OO Standby On oo O Standby On O Wait 90 seconds 00 00 00 00 01 00 00 00 30 OO E gt en Power 1 Press the Standby On button The Shutdown screen will display Select the YES option press Keystone buttons or Disk Pad button to turn off 2 The fan will continue to run for approximately 90 seconds 3 Disconnect power cord from wall socket 4 Disconnect cables if moving projector to new location 3M IPC 2001 3M Personal Projector MP7630B MP7730B 17 Operation Main Menu Press Menu on the remote control or external control pad and the main menu will display on the screen Press Menu again to enter page items and press Keystone buttons to select sub menus The main menu will go off automatically 1f there is no further action from user for 10 seconds Press the Auto button to leave the current sub menu and press Auto again to leave the main menu Menu Pages VOL Display Menus Image Menus Control Menus A da Video Module Auto Size Language Keystone Without Horizontal Phase Mirror Optional Brightness Video Contrast B Module Horizontal Position Auto Off Color Balance Horizontal Sync Blank not applicable Vertical Position Reset Auto Size Language Source PC or Mac Keystone with Brightness Optional Horizontal Sync Blank Treble Video Contras
16. cf EX Off On a S EJ 3M Personal Projector MP7630B MP7730B 3M IPC 2001 Maintenance Lamp Usage Use and Replacement of Lamp The projector lamp has a normal operating time of approximately 1200 to 1500 hours called the lamp life During the normal lamp life the picture will be bright and the colors clear If the lamp is used beyond the normal lamp life the picture will become dark and the colors poor Always replace lamps with new ones Using an old lamp in the projector could cause a malfunction When the power is turned on the LAMP indicator will light up red or a message will be displayed to indicate when it is time to replace the lamp Consult your dealer Lamp Temperature Status LED Indicators Lamp Exceed Service Hours When this LED lights red continuously it is warning you that the lamp has exceeded 1500 service hours Replace the projection lamp immediately PLEASE CHANGE A NEW LAMP AND RESET THE TIMER The lamp has been operated for 1400 hours PLEASE CHANGE A NEW LAME THE POWER WILL TURN OFF AFTER 20 HOURS The lamp has been operated for 1480 hours and the power will turn off after 20 more hours PLEASE CHANGE A NEW LAMP The lamp has been operated for more than 1500 hours and the power will turn off automatically after 10 minutes All of these messages will not display for more than 3 minutes but each message will be dis played whenever you turn on the lamp again Lamp is not well
17. deo from a VCR S Video and Tuner The projector will then search for the selected type of signal until it is found or switched to another type O Source button source Scanning Channels The MP7630B MP7730B can receive over 100 television channels In Tuner mode TV and CATV press the Scan button on the remote control to view all available television channels The message DO YOU REALLY WANT TO SCAN YES NO will appear onscreen Press either the left or right arrow buttons on the remote to reach Yes or No then press the Menu button to enter the selected answer The message TUNER IS SCANNING NOW will display for a few seconds and then the scanned channels will appear for a few seconds each OO Scan button Left and Right buttons 24 3M Personal Projector MP7630B MP7730B 3M IPC 2001 Optional Video Module Image Sub Menu This menu is only available when the input signal is from Video S Video TV or CATV m E se Image Ratio DIR Normal E 16 9 Video System Auto E PAL M E PAL N E SECAM Color E y gt gt Less ES More Red lt A gt Green Source is video or S video Image Ratio 4 3 Normal 16 9 Video Auto PAL M PAL N SECAM O 3M IPC 2001 3M Personal Projector MP7630B MP7730B E Optional Video Module Operation 1 Go into the menu system and move to the Source sub menu Use the Menu button on the control pad or remote control unit to scroll through items in the
18. e over the Notebook or PowerBook mouse function When the Magnify func tion is activated use the Disk Pad to move around the display areas Note The mouse function is not available when the Magnify function is turned on R Click L Click Disk Pad button These two keys are used when the mouse function 1s activated after the PS 2 port is connected They act as the right R and left L buttons of a computer mouse L Click button R Click button Drag This button toggles between ON and OFF for the drag function of the remote mouse Ca Drag button Blank Press this button to activate or release the Blank function Blank makes the screen go blank x Blank button Installing or Replacing Batteries e Push and slide the battery compartment lid in the direction shown e Install two AAA batteries as indicated by the diagram inside the compartment e Position the lid over the compartment and snap back into place Y 4 4 3M Personal Projector MP7630B MP7730B 3M IPC 2001 System Setup Screen Chart Place the projector at the required distance from the screen according to the desired picture size see the table below Screen Size Distance to Screen Width Height Diagonal Minimum Maximum 67 9 cm 50 9 cm 84 8 cm 15m 20m Lens center 27 in 20 in 33 4 in 5 0 ft 7 0 ft 101 2cm 75 9 cm 126 5 cm 23m 3 0m 40 in 30 in 49 8 in
19. eproduction of this manual in any form without prior permission is strictly prohibited 3M will replace the manual if any pages are missing or collated incorrectly O 3M IPC 2001 3M Personal Projector MP7630B MP7730B EJ Important Notice All statements technical information and recommendations related to 3M s products are based on information believed to be reliable but the accuracy or completeness is not guaranteed Before using this product you must evaluate it and determine if it is suitable for your intended application You assume all risks and liability associated with such use Any statements related to the product which are not contained in 3M s current publications or any contrary statements contained on your purchase order shall have no force or effect unless expressly set forth in a written agreement signed by an authorized officer of 3M Warranty and Limited Remedy This product will be free from defects in material and manufacture for a period of two years from the date of purchase Exclusion to Warranty The lamps are considered a consumable item and are warrantied for 90 days or 180 hours whichever occurs first 3M MAKES NO OTHER WARRANTIES INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE If this product is defective within the warranty period stated above your exclusive remedy shall be at 3M s option to replace or repair the 3M product or refund the purchase price
20. g safety labels are used on or within the MP7630B MP7730B projector to alert you to items or areas requiring your attention AA AX AX Lamp Unit 60 11502 001 HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE WHEN REPLACING THE LAMP TURN OFF THE PROJECTOR AND PULL OUT THE CORD FROM THE RECEPTACLE BEFORE REPLACING THE LAMP WAIT UNTIL THE LAMP BECOMES COOL MINIMUM 45 MINUTES TOUCHING THE LAMP WHEN IT IS HOT MAY CAUSE A BURN ON YOUR HAND HIGH PRESSURE LAMP WHEN HOT MAY EXPLODE IF IMPROPERLY HANDLED REFER TO USER S GUIDE HAUTE TENSION HAUTE TEMPERATURE HAUTE PRESSION ETEIGNEZ LE PROJECTEUR ET D BRANCHEZ LE CORDON D ALIMENTATION DE LA PRISE AVANT DE REMPLACER L AMPOULE LAISSEZ REFROIDIR L AMPOULE U MOIN 45 MINUTES AVANT DE LA RETIRER POUR NE PAS VOUS BRULER LES MAINS EN CAS DE MAUVAISES MANIPULATION LES AMPOULES HAUTE PRESSION RISQUENT D EXPLOSER QUAND ELLE SONT CHAUDES CONSULTEZ LE MODE D EMPLOI HOHSPANNUNG HOCH TEMPERATUR HOCHDRUCK BEIM AUSWECHSELN DER GL HLAMPE DEN PROJEKTOR AUSSCHALTEN UND NETZKABEL AUS DER WANDSTECKDOSE ABZIEHEN VOR DEM AUSWECHSELN DER GL HLAMPE WARTEN BIS SICH DIE LAMPE ABGEK HLT HAT MINDERSTENS 45 MINUTEN DARAUF ACHTEN DAB DIE HEIBE GL HLAMPE NICHT BER HRT WIRD DA DIES VERBRENNUNGEN VERURSACHEN KANN BEI UNSACHGEMASSER BEHANDLUNG KANN DIE UNTER HOEHM DRUCK STEHENDE BIRNE EXPLODIEREN SICH AUF DIE BEDIENUNGSANLEITUNG BEZIEHEN ALTO VOLTAGGIO ALTA TEMPERATURA ALTA PRESSION SE SI DEVE SOSTIT
21. le Video Module Connection Speaker Cable Television CATV Connection RCA Cable Connection a Video Yellow b Audio White Red S Video Connection Headphone Jack 7 SCART Connection BE D Nu Back of projector with PAL SCART Module Top view of video module Optional Video Module Connections o Video Audio L Audio L Audio R OUT OUT OUT OUT OUT our OO YEL WHT RED WHT RED E o a VCR Laser Disc E som Ul 1111 O 3M IPC 2001 3M Personal Projector MP7630B MP7730B E Optional Video Module Attaching the Optional Video Module to the MP7630B MP7730B 1 Precisely align the two metal tabs on the bottom of the module and insert into the corresponding slots on the back of the projector 2 Slowly push the module to fit with the unit Make sure that the module plugs into the AV con nection on the projector 3 Plug the correct cable into the corresponding jack or port in the back of the unit 4 Select inputs by pressing the Source button and select the appropriate source channel by pressing the Channel Up Down buttons Switching Input Signals Pressing the Source button on the remote control or the projector will cycle between these choices of input signals RGB computer Video composite vi
22. n until the Lamp Hour item is selected 2 Press Keystone to display the lamp usage on the bottom of the screen Press again to select Reset Lamp O Hr Reset Cancel 3 Press the Menu button to reset the time usage 4 Press the Auto button to save the setting and exit the menu system 32 3M Personal Projector MP7630B MP7730B 3M IPC 2001 Troubleshooting Plug the power cord into the AC inlet NO POWER Y Plug the power cord into the power inlet Wait 2 minutes after turning off the projector before turning it back on Check that you have selected the proper input source to project v Ensure that all cables are connected properly NO PICTURE Y Adjust the brightness and contrast Y Remove the lens cap IMAGE ISN T SQUARE ON Reposition the unit to improve its angle to the screen SCREEN v Is the vertical offset properly corrected using the keystone function Y Select the correct video system POOR Coron Y Adjust the brightness contrast and saturation Y Adjust the focus Y Reposition the unit to improve its angle to the screen Ensure that the distance between the unit and the screen is within the adjustment range of the lens IMAGE IS BLURRED Replace the batteries with new ones REMOTE CONTROL Y Make sure there are no obstacles between the remote control and the unit DOESN T WORK Y Operate remote control within 4 meters 13 feet of the unit Y Make sure n
23. ntrol Menu Oo MENU gt Menu x1 Auto Press lt or gt to reset Language M En Fr De Mit Es Po Mi 9 O x2 Mirror Normal E H Iinv E V Inv E H V Inv MENU Auto Off o Stop EUR 15 O o Menu x1 Lamp Hour 2 8 Hours Auto Will automatically adjust projected image English En French Fr Deutsch De Italian It Espa ol Es Portuguese Po Simplified Chinese Mirror Will invert image to display properly according to position of projector Normal H Inv Horizontally V Inv Vertically H V Inv Horizontally Default Inverted Inverted Vertically Inverted Rear screen Ceiling Rear screen A od mounted projection ceiling XE mounted NMR Auto Off Will turn off the power in 60 minutes 00 00 00 00 60 00 O gt Will reset the lamp hours after lamp is changed be 3M Personal Projector MP7630B MP7730B 3M IPC 2001 Optional Video Module Features The Optional Video Module makes it possible to hook the MP7630B MP7730B to a laser disc VCR or other video devices Two versions will be available an NTSC Package with RCA connectors and television tuner and a PAL package with a SCART connector and no television tuner CASA a NTSC Package PAL Package e NTSC Tuner Module PAL Video Module Il e CATV e S Video e S Video e SCART connector _ e 3 RCA e Audio e Audio Back of projector without Optional Video Modu
24. ntrol unit Channel Select Press the channel number button user wants to select for example 12 then press Return button to set Channel Up Down Go up and down through channels by pressing the Channel Up Down buttons The channel number will appear in the lower right corner of the screen If there is no further action for three seconds the channel number display will disappear automatically Scan Press the Scan button for two seconds to begin scanning TV channels Add Erase Press the Add Erase button for two seconds to add or erase the channel To delete channels from memory press the button to erase the channel A Channel Erased message will display Users can also add channels to memory by pressing the button after selecting 1t A Channel Added message will display Channel Erased Channel Added Reverse Press the Reverse button to toggle between the previous and current channels O 3M IPC 2001 3M Personal Projector MP7630B MP7730B Ed Optional Video Module Source Menu Menu MN E EJ es ne Ea Q o Source PC E Video m S Video E Tuner Menu Volume O O Treble Bass Menu o5 am a Menu Tuner Press lt or gt to select PC Video S Video Tuner YEL WHT RED WHT RED E VCR Laser Disc sessss Ls LL Ul go Cable Box E 0 29 PL 0 15 ER os
25. occconccconononoconaconnccnaconacnno 78 8118 8397 0 Adapter Serial MOus cccstsetees ciniti ated i conven da do cedida 78 8118 8396 2 General Cables ss iii liar tabs RORA se 78 8118 8394 7 VGA Cable Linie ART Ari ad ea aaa 78 8118 3401 5 Mac Adapter switchable ss 78 8118 3308 2 150W Lampe Ghai anaes ini dali Ghee 78 6969 9036 1 Remote Control rides ins A tante rein eee tnd Ads 78 8118 8398 8 Softside Carrying Casta Ars dar 78 6969 9034 6 Lens Cover ena a llo EAA TRETE 78 8118 8399 6 Not Included with Basic Packet Description Part Number NTSC Optional Video Module RCA with Tuner 78 6969 9038 7 PAL Optional Video Module SCART cocoonoccnnocccnnoncconnncconononanononanacannncnnno 78 6969 9104 7 3 Conductor Video Audio Cable 78 8118 3234 0 Stereo Mini Jack Cable ss 78 8118 8290 7 SE VideG Cabl iii is 78 8118 3538 1 SEARTRCA Adapter cenital iii asa gel ha faites bla estria te fe DY 0205 1011 0 Ordering Parts or Getting Information For product information product assistance service information or to order accessories please contact 3M Customer Service at the following number e In U S or Canada 1 800 328 1371 e In other locations contact your 3M Sales office The contents of this manual are subject to revision without prior notice 3M assumes no responsibility for the infringement of special rights of a third party or other rights that may arise out of the information contained in this manual R
26. ojection lamp e RS 232 control capability The MP7630B MP7730B Personal Projector offers the following optional features e Attachable video module e Cable television CATV tuner Note The brightness of your machine will vary depending on the ambient room conditions and contrast brightness settings External Control Pad Buttons The External Control Pad is located on top of the projector near the back end The Infrared Remote Receivers allow the projector to accept signals from the remote control For best results be sure to aim the control toward the sensors without any obstructions between the two and at a distance no greater than 4 meters 13 feet The Menu button will display the menu system onscreen Press Menu again to access the sub menus The Keystone buttons help correct keystone distortion of a projected image The Keystone button corrects distortion in the upper part of the image The Keystone corrects it in the lower part When you are viewing the onscreen menus the Keystone buttons help navigate among choices and settings in the sub menus Press the Auto button to automatically adjust a projected image on screen When you are viewing the onscreen menus press Auto to go back to the Main Menu Press Auto again to exit the menu system The Lamp Status Indicator will blink or light up when the lamp needs service cooling or replacement See page 34 for more detailed information When the projector is tu
27. onds when the freeze function is released To release the freeze function press the Freeze button or Source button when the input source is switched over during a mn nm a Freeze button Pause icon Play icon Mute Pressing the Mute button will mute the sound A text box saying Mute appears at the lower right of the screen Press Mute button again or Volume or button to release the function Mute button Volume Press the Volume or button to adjust the loudness The volume slide bar will disappear three seconds after the last adjustment is made Volume button Magnify By pressing Magnify the center of the picture can be magnified doubling in size When the button 1s pressed again the picture is further magnified up to four times the original size By pressing Magnify the size of the image is reduced to half its size When the button is pressed again the picture is further reduced until it is restored to the original size To return to the normal display mode press the Return button This function can be used in combination with the Freeze function ty SY EI Magnify button Magnify icon O 3M IPC 2001 3M Personal Projector MP7630B MP7730B Introduction Laser Press this button to generate the laser beam that functions as a red pointer on the screen Laser button Disk Pad If the PS 2 ADB mouse cable is connected with the PC Notebook or Mac PowerBook mouse port the Disk Pad can tak
28. ookups with the power The 2 prong adapter with ground is used with older U S electrical outlets that only support off 2 prong power cord plugs Note When using this adapter the ground lead MUST be securely fastened to the ground screw on the outlet Plug the 2 prong adapter into the bottom socket O of the eletrical outlet Hook the end of the ground lead firmly around the neck of the outlet s ground screw Tighten the screw 1f necessary to hold the ground in place Then plug the power cord into the adapter O 1 KR ob Oo ZN Q 60000 7 00000 Standby On OO Standby On 1 Plug power cord into wall socket Wait 5 seconds before pressing the Standby On button L0000 Y 2 Press the Standby On button and hold for 3 seconds e The ON indicator will blink green during warm up and lamp ignition When power is turned off there is a 90 second reset period before the Standby On button will function again 3 Turn on all connected equipment Y Note Ifyou have the Optional Video Module attached to the unit press the Source button on the remote to select the source of the signal to be projected onto the screen The selected signal input is displayed at the top right of the screen The display will show the last selected input source before power was turned off For more information please refer to the Optional Video Module section of this manual E 3M Person
29. othing blocks the receiver on the control pad Y Check the audio cable connection from audio input source Y Adjust the audio source Y Press VOLUME button Y Press MUTE button O 3M IPC 2001 3M Personal Projector MP7630B MP7730B EJ Troubleshooting Status Indicator Lights and Messages Message Displayed Meaning and Solution if applicable SEARCHING Projector cannot identify input signal INPUT SIGNAL DETECTED ACTIVATING AUTO IMAGE Projector has identified input signal The input signal s horizontal frequency exceeds the range of the SYNC IS OUT OF RANGE projector s CHANGE THE LAMP AND The lamp has been operated for over 1200 hours and needs to be RESET THE LAMP TIMER replaced soon CHANGE THE LAMP THE POWER WILL TURN OFF AFTER 20 HOURS The lamp has been operated for 1479 hours and the power will shut off after 20 more hours Replace the lamp as soon as possible CHANGE THE LAMP The lamp has been operated for over 1500 hours Power will blinking with LED lighting red automatically shut off in 10 minutes Replace the lamp immediately El 3M Personal Projector MP7630B MP7730B O 3M IPC 2001 Service Information Accessories Description Part Number Power Cord EU cui A since DY 0205 1354 4 Power Cord US RITA DY 0205 1356 9 Power Cord WO A en ile DY 0205 1355 1 Adapter PS 2 MOUSE cia seregrar uth et nine niet 78 8118 8395 4 Adapter ADB Apple Desktop Bus Mouse ooooon
30. rned on the Standby On Indicator will blink during warm up and lamp ignition then stay green to indicate the projector is ready for use Press the Standby On Button to turn the projector on or off e 8 MENU KEYSTONE AUTO l Lamp Infrared Stat Remote alus Standby On Receiver Indicator Button yal Ao Standby On Keystone Indicator 3M IPC 2001 3M Personal Projector MP7630B MP7730B EJ Introduction Remote Control Identification Standby On Press STANDBY ON button to begin projection mode lamp on To turn lamp off press STANDBY ON then select YES on Shutdown screen Select NO to continue running Menu Press to display the menu screen Freeze Press button to turn the freeze image function ON OFF L Click Press for left mouse button function Mouse Mode Press for select function Menu Mode Drag In mouse mode press button to hold reposition and drop an object on the screen To MAGNIFY an area press MAGNIFY button then press the DRAG button and change the magnifying position by moving the Disk Pad Magnify Press to increase or to decrease the size of the displayed image Return Press button to return to last menu or command Channel Up and Down Press A button to increase the channel number Press Y button to decrease the channel number Source Press button to change input source ANDBY ON SER OURCE o O MENU E FREEZE BLANK x Ko
31. rranty or repair service Limitation Of Liability THE FOREGOING WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED AND 3M SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE 3M SHALL NOT BE LIABLE FOR ANY DAMAGES DIRECT CONSEQUEN TIAL OR INCIDENTAL ARISING OUT OF THE USE OR INABILITY TO USE THIS PRODUCT Important The above warranty shall be void if the customer fails to operate product in accordance with 3M s written instructions This warranty gives you specific legal rights and you may have other rights which vary from state to state FCC STATEMENT CLASS B This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications How ever there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can by determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help In
32. structions to Users This equipment complies with the requirements of FCC Federal Communication Commission equipment provided that following conditions are met The cables power cord RGB cable and other cables may have to be used with the core set to the projector side Use the cables which are included with the projector or specified EEC STATEMENT This machine was tested against the 89 336 EEC European Economic Community for EMC Electro Magnetic Compatibility and fulfills these requirements Video Signal Cables Double shielded coaxial cables FCC shield cable must be used and the outer shield must be connected to the ground If normal coaxial cables are used the cable must be enclosed in metal pipes or in a similar way to reduce the interference noise radiation Video Inputs The input signal amplitude must not exceed the specified level Patents Trademarks amp Copyrights IBM is a registered trademark of International Business Machines Corporation Apple Macintosh and Apple Powerbook are registered trademarks of Apple Computer Inc Microsoft and Windows 95 and Windows 98 are registered trademarks and Windows and Windows for Workgroups are trademarks of the Microsoft Corporation Toshiba is a registered trademark of Toshiba Corporation All other products are trademarks or registered trademarks of their respective companies 6 3M Personal Projector MP7630B MP7730B 3M IPC 2001 Introduction
33. t Module Sharpness Horizontal Phase Mirror Volume Horizontal Position Auto Off Bass Vertical Position Reset Mute Language Source Video Keystone Tint Input Mirror Volume with Brightness Sharpness Blank Treble Optional Contrast Image Ratio Video Auto Off Bass Module Color Balance System Reset Mute E 3M Personal Projector MP7630B MP7730B 3M IPC 2001 Menu Navigation 00 00 KEYSTONE Keystone Brightness O 9 ee o Es o Contrast Color Balance E a 059 Menu X Keystone Brightness Contrast Color Balance Display Menu O 3M IPC 2001 3M Personal Projector MP7630B MP7730B 19 Operation Display Menu 0 255 Brightness 0 255 0 255 Color Balance 0 2 3M Personal Projector MP7630B MP7730B 3M IPC 2001 Image Menu 1 Menu oO Menu 0060 9 0 Menu x1 Auto Resize x1 H Phase x1 H Size H Position V Position Auto Resize Will automatically adjust image to fit onto screen Off On AMIEL Auto Resize OFF 0 31 Horizontal Size Auto Resize OFF 65 _ 193 NA lt 0 255 Vertical Position Auto Resize OFF Horizontal Position KELE Auto Resize OFF 0 255 0 255 A Ge Sy S7 f S 65 193 193 ts gt a 3M IPC 2001 3M Personal Projector MP7630B MP7730B Co
34. tatus Light Messages sucias 34 Service Information ACCESSOTIOS iii iii 35 Ordering Parts or Getting Information 35 The Appendix is in English only Please click here on the CD ROM to read it O 3M IPC 2001 3M Personal Projector MP7630B MP7730B Ea Introduction Intended Use Before operating the machine please read the entire manual thoroughly The 3M Personal Projector MP7630B MP7730B was designed built and tested for use indoors using 3M lamps 3M ceiling mount hardware and nominal local voltages The use of other replacement lamps outdoor operation operation in environments containing heavy cigarette smoke or different voltages has not been tested and could damage the projector or peripheral equipment and or create a potentially unsafe operating condition Important Safeguards 1 Read and understand all instructions before using Pay particular attention to areas where these symbols are shown AN WARNING Indicates a potentially hazardous situation which if not avoided could result in death or serious injury Note Used to emphasize important conditions or details 2 Close supervision is necessary when any appliance is used by or near children Do not leave appliance unattended while in use 3 Never look directly into the projector lens when the lamp is on The high pressure mercury lamp produces a strong light that could damage your eyesight 34 Care must be taken as burns can occur from touching

3M MP7630B Owner's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents