12Volt Chainsaw Sharpener 141259 Owner's Manual
Contents
1. pIeiaAL Tools 12 VOLT BAR MOUNT CHAIN SAW SHARPENER OWNER S MANUAL PAIS WARNING Read carefully and understand all INSTRUCTIONS before operating Failure to follow the safety rules and other basic safety precautions may result in serious personal injury Item 141259 Thank you very much for choosing a NORTHERN TOOL EQUIPMENT CO INC Product For future reference please complete the owner s record below Model Purchase Date Save the receipt warranty and these instructions It is important that you read the entire manual to become familiar with this product before you begin using it This machine is designed for certain applications only Northern Tool Equipment cannot be responsible for issues arising from modification We strongly recommend this machine is not modified and or used for any application other than that for which it was designed If you have any questions relative to a particular application DO NOT use the machine until you have first contacted Northern Tool Equipment to determine if it can or should be performed on the product For technical questions please call 1 800 222 5381 INTENDED USE This unit allows chain sharpening without removing the chain from the bar TECHNICAL SPECIFICATIONS amp PACKING LIST Item Description Installed power Electrical motor max 12V supply Wheel thickness 1 8 in 3 2mm and 3 16 in 4 7 mm Maximum speed 5500 RPM Type2. from children TOOL USE AND CARE Do not force the tool Tools do a better and safer job when used in the manner for which they are designed Plan your work and use the correct tool for the job Never use a tool with a malfunctioning switch Any power tool that cannot be controlled with the switch is dangerous and must be repaired by an authorized service representative before using Disconnect power from tool and place the switch in the locked or off position before servicing adjusting installing accessories or attachments or storing Such preventive safety measures reduce the risk of starting the power tool accidentally Secure work with clamps or a vise instead of your hand to hold work when practical This safety precaution allows for proper tool operation using both hands Use only accessories that are recommended by the manufacturer for your model Accessories that may be suitable for one tool may create a risk of injury when used on another tool Keep guards in place and in working order Never leave tool running unattended Never stop the grinding wheel with your hands even after stopping the motor Check that all power is disconnected when changing grinding wheels during maintenance or transporting Never start the sharpener without the wheel guard in place The guard is supplied with the accessories bag and must be installed before operation The guard can be removed only for wheel replacement then it mu
3. of chains pitches 1 4in 325in 3 8in 404in Weight sharpener 4 5 Ibs 2 kg GENERAL SAFETY RULES accu Read and understand all instructions Failure to follow all instructions listed below may result in electric shock fire and or serious injury Ty esau The warnings cautions and instructions discussed in this instruction manual cannot cover all possible conditions or situations that could occur It must be understood by the operator that common sense and caution are factors which cannot be built into this product but must be supplied by the operator SAVE THESE INSTRUCTIONS WORK AREA Keep work area clean free of clutter and well lit Cluttered and dark work areas can cause accidents Do not use your tool where there is a risk of causing a fire or an explosion e g in the presence of flammable liquids gasses or dust Power tools create sparks which may ignite the dust or fumes Page2 of 8 Keep children and bystanders away while operating a power tool Distractions can cause you to lose control so visitors should remain at a safe distance from the work area Be aware of all power lines electrical circuits water pipes and other mechanical hazards in your work area particularly those hazards below the work surface hidden from the operator s view that may be unintentionally contacted and may cause personal harm or property damage Be alert of your surroundings Using power tools in confined work areas may pu
4. e sure the wheel is securely installed and always check wheel for any damage before each use NEVER use without wheel guard installed NEXT Install the sharpener onto chain saw chain bar approximately centered Notes This machine is equipped with a safety switch with a release coil The provided power cables are complete with terminals for quick and safe connection to any 12V battery This allows the operator to use this sharpener on the job or in the field wherever a 12V battery is available Page5 of 8 MAINTENANCE FA scsi Make sure this tool is disconnected from its power source before attempting any maintenance cleaning or inspection Maintain your tools It is recommended that the general condition of any tool be examined before it is used Keep your tools in good repair by adopting a program of conscientious repair and maintenance in accordance with the recommended procedures found in this manual If any abnormal vibrations or noise occurs turn the tool off immediately and have the problem corrected before further use Have necessary repairs made by qualified service personnel Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control Keep handles dry clean and free from oil and grease Cleaning Use only soap and a damp cloth to clean your tools Many household cleaners are harmful to plastics and other insulation Never let liquid ge
5. fornia to cause cancer birth defects or other reproductive harm Some examples of these chemicals are e lead from lead based paints e crystalline silica from bricks and cement and other masonry products and e arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as those dust masks that are specially designed to filter out microscopic particles Northern Tool Equipment Co 2800 Southcross Drive West P O Box 1499 Burnsville MN 55337 0499 Made in China Page8 of 8
6. gles or safety glasses with side shields which comply with current national standards or when needed a face shield Use as dust mask in dusty work conditions This applies to all persons in the work area Also use non skid safety shoes hardhat gloves dust collection systems and hearing protection when appropriate Avoid accidental starting Do not carry the power tool with your finger on the switch Ensure the switch is in the off position before plugging tool into power outlet In the event of a power failure while a tool is being used turn the switch off to prevent surprise starting when power is restored Do not overreach Keep proper footing and balance at all times Remove adjusting keys or wrenches before connecting to the power supply or turning on the tool Awrench or key that is left attached to a rotating part of the tool may result in personal injury Never wear rings bracelets and or loose clothing that could come into contact with the grinding wheel Always wear gloves and approved protective eyewear while operating or maintaining the sharpener Before starting up the sharpener check that the working area is free of tools or other objects Keep all other people or by standards away from work area during its operation Always work in a stable and safe position Page3 of 8 Only allow users familiar with the sharpener s operation to use the sharpener Store the sharpener in a safe dry place when not in use Keep away
7. st be reinstalled Check that the voltage and frequency indicated on the sharpener correspond to supplied power Never use higher rated power supply as this will damage the sharpener Never use defective and or non standard cables plugs or extension cables Remove power or cables immediately if cables show signs of damaged or are cut The power supply cables are complete with terminals Never use cables that are manipulated in any way Check the cable position during operation making sure that cables stay away from grinding wheels during operation Never work near other electrical cables Never advance the chain with your hands until the grinding wheel has moved entirely back to the upright position non cutting position Before starting the grinder always check that the grinding wheel is correctly installed and not damaged Before using the sharpener check any safety or other devices are properly working Never use the sharpener as a cutter or for grinding objects other than saw chains Never use near or expose sharpener to any explosive or flammable liquids or environment Never start the sharpener with hands or fingers touching or near wheel Never force the sharpener or any tool while working maintaining or sharpening Page4 of 8 ASSEMBLY OPERATION FIRST Check that you have proper size grinding wheel to match your chain Check your chain saw specifications for proper wheel size B
8. t inside a tool Always disconnect from power source before carrying out any maintenance lubrication or cleaning operations Keep sharpener clean using a cloth rag with soap and water Always dry after cleaning Never use compressed air for cleaning it can cause wood or metal dust to reach small areas in the sharpener causing damage to essential components of the sharpener Page6 of 8 DIAGRAM amp PARTS LIST 10 1 f Parts Description Qty Parts Description Qty 1 Grinding wheel cover 1 16 Cable Set 1 2 Self tapping screw 1 17 lock nut 1 3 Grinding wheel 1 18 Reset spring 4 4 Grinding wheel 1 19 Adjustment bolt 4 5A aninaing o EONS 1 20 Torsion limit board 1 5B Grinding wheel seat 1 22 Torsion 1 6 Axis Card 1 23 Elastic clip chain plate 2 7 Antifriction pad 1 24 Rotating Seat 1 8 Torsion Cover 2 25 bearing spring 2 10 Body 1 26 Angle plate 1 10 1 Handle 1 27 lock nut 1 11 PCB board 1 28 M5 nut 1 12 Pressure Line board 1 32 Limited board Set 1 13 Electrical Set 1 33 bolt M5X10 1 14 Self tapping screw 4 34 Gauge 1 Switch Cover 1 35 Shaping of sand 1 For replacement parts and technical questions please call 1 800 222 5381 Page7 of 8 WARRANTY One year Limited Warranty WARNING Some dust created by power sanding sawing grinding drilling and other construction activities contains chemicals known to the State of Cali
9. t you dangerously close to cutting tools and rotating parts ELECTRICAL SAFETY PAN AA Always check to ensure the power supply corresponds to the voltage on the rating plate Do not abuse the cord Never carry a portable tool by its power cord or yank tool or extension cords from the receptacle Keep power and extension cords away from heat oil sharp edges or moving parts Replace damaged cords immediately Damaged cords may cause a fire and increase the risk of electric shock Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock The sharpener motor can be used continuously for 20 minutes then it needs to be turn off to cool down to avoid possible damage from over heating If sharpening chain on an electrical saw always disconnect the electrical saw power cable PERSONAL SAFETY Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool while you are tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury Dress properly Do not wear loose clothing dangling objects or jewelry Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts Air vents often cover moving parts and should be avoided Use safety apparel and equipment Use safety gog
Download Pdf Manuals
Related Search