Seagate Laptop SSHD ST1000LM015 hard disk drive
Contents
1. DRIVE SPECIFICATIONS 2 12 AGENCY CERTIFICATION 2 12 1 Safety certification These products are certified to meet the requirements of UL60950 1 CSA60950 1 and EN60950 and so marked as to the certify agency 2 12 2 Electromagnetic Compatibility EMC Hard drives that display the CE mark comply with the European Union EU requirements specified in the Electromagnetic Compatibility Directive 2004 108 EC as put into place 20 July 2007 Testing is performed to the levels specified by the product standards for Information Technology Equipment ITE Emission levels are defined by EN 55022 Class B and the immunity levels are defined by EN 55024 Drives are tested in representative end user systems Although CE marked Seagate drives comply with the directives when used in the test systems we cannot guarantee that all systems will comply with the directives The drive is designed for operation inside a properly designed enclosure with properly shielded I O cable if necessary and terminators on all unused I O ports Computer manufacturers and system integrators should confirm EMC compliance and provide CE marking for their products Korean RRL If these drives have the Korean Communications Commission KCC logo they comply with paragraph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility EMC Framework requirements of the Radio Research Laboratory RRL Communications Commissi2. 18 SERIAL ATA SATA INTERFACE Table 9 Supported ATA commands ATA standard commands names Command code in hex Set Multiple Mode C6h S M A R T Disable Operations BOh D9h S M A R T Enable Disable Autosave BOh D2h S M A R T Enable Operations BOh D8h S M A R T Enable Disable Auto Offline BOh DBh S M A R T Enable One Attribute Modification BOh EOh S M A R T Execute Offline BOh D4h S M A R T Free Fall Protection Host Interface FEh S M A R T Read Attribute Thresholds BOh D1h S M A R T Read Data BOh DOh S M A R T Read Log Sector BOh D5h S M A R T Return Status BOh DAh S M A R T Save Attribute Values BOh D3h S M A R T Write Attribute Thresholds BOh D7h S M A R T Write Attribute Values BOh E1h S M A R T Write Log Sector BOh D6h Write Buffer E8h Write DMA CAh Write DMA Extended 35h Write DMA without Retries CBh Write Long with Retries 32h Write Long without Retries 33h Write Multiple C5h Write Multiple Extended 39h Write Sectors 30h 31h Write Sectors Extended 34h ATA standard power management commands Check Power Mode E5h Idle E3h Idle Immediate Eth Sleep E6h Standby E2h Standby Immediate E0h ATA standard security commands Security Set Password Fih Security Unlock F2h Security Erase Prepare F3h Security Erase Unit F4h Security Freeze Lock F5h Security Disable Password F6h SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C 19 5 3 1 Identify Devi
3. Sector Count register values 004 Set PIO mode to default PIO mode 2 Oly Set PIO mode to default and disable IORDY PIO mode 2 084 PIO mode 0 094 PIO mode 1 0Ay PIO mode 2 OBy PIO mode 3 OC PIO mode 4 default 204 Multiword DMA mode 0 214 Multiword DMA mode 1 224 Multiword DMA mode 2 40y Ultra DMA mode 0 41 Ultra DMA mode 1 424 Ultra DMA mode 2 434 Ultra DMA mode 3 444 Ultra DMA mode 4 45y Ultra DMA mode 5 46y Ultra DMA mode 6 55H Disable read look ahead read cache feature 824 Disable write cache AAy Enable read look ahead read cache feature default Cly Disable the Free Fall Protection feature 414 above enables the Free Fall Protection feature Fly Report full capacity available At power on or after a hardware or software reset the default values of the features are as indicated above SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C 24 SERIAL ATA SATA INTERFACE 5 3 3 S M A R T commands S M A R T provides near term failure prediction for disk drives When S M A R T is enabled the drive monitors predetermined drive attributes that are susceptible to degradation over time If self monitoring determines that a failure is likely S M A R T makes a status report available to the host Not all failures are predictable S M A R T predictability is limited to the attributes the drive can monitor For more information on S M A R T commands and implementation se
4. DRIVE SPECIFICATIONS PERFORMANCE REFERENCE TEST DESCRIPTION LEVEL STANDARD Electrostatic discharge Contact HCP VCP 4 kV Air 4 B EN 61000 4 2 95 80 to 1 000 MHz 3 V m n i Radiated RF immunity 80 AM with 1 kHz sine A ae ea 900 MHz 3 V m 50 pulse modulation 200 Hz Electrical fast transient t 1 kV on AC mains 0 5 kV on external I O B EN 61000 4 4 95 Surge immunity E 1 kV differential 2 kV common AC mains B EN 61000 4 5 95 Conducted RF immunity 150 kHz to 80 MHz 3 Vrms 80 AM with 1 kHz sine A EN 61000 4 6 97 Power Frequency H field 1 A m 50Hz 60Hz 3 axes A EN 61000 4 8 97 immunity 30 Reduction for 25 cycles C Voltage dips interrupts gt 95 Reduction for 250 cycles C EN 61000 4 11 94 gt 95 0 5 cycles B 2 11 RELIABILITY Nonrecoverable read errors 1 per 101 bits read max Load Unload U UL 25 C 50 relative humidity 600 000 software controlled power on off cycles 20 000 hard power on off cycles Warranty SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C To determine the warranty for a specific drive use a web browser to access the following web page http www seagate com support warranty and replacements From this page click on the Verify Your Warranty link You will be asked to pro vide the drive serial number model number or part number and country of pur chase The system will display the warranty information for your drive
5. 67 Minimum PIO cycle time without IORDY flow control 240 ns 00784 68 Minimum PIO cycle time with IORDY flow control 120 ns 00784 69 74 ATA reserved 00004 75 Queue depth 001Fy 76 Serial ATA capabilities 0DO06y 77 ATA reserved 00004 78 Serial ATA features supported 00484 79 Serial ATA features enabled 00484 80 Major version number 01F0y 81 Minor version number 0029y 82 Command sets supported 746By 83 Command sets supported 7D69y 84 Command sets support extension 61E3y 85 Command sets enabled 7469 86 Command sets enabled BC49y 87 Command sets enable extension 61E3y 88 Ultra DMA support and current mode see note following this table xxTFy 89 Security erase time XXXXH 90 Enhanced security erase time XXXXH 91 Current APM values 80804 92 Master password revision code FFFEy 93 Hardware reset value see description following this table XXXXH 94 Auto acoustic management setting XXXXH 95 Stream Min Request Size 00004 96 Streaming Transfer Time DMA 00004 97 Streaming Access Latency DMA and PIO 00004 SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C 21 Table 10 Identify Device command SERIAL ATA SATA INTERFACE Word Description Value 98 99 Streaming Performance Granularity 00004 100 Total number of user addressable LBA sectors available ST1000LM014 1 953 525 168 103 see Section 3 2 for related information ST1000LM015 1 953 525 168 These words are required for drives that support the 48 bit ad
6. are placed on covers to protect against unauthorized physical access In addition Security Level 2 requires at a minimum role based authentication in which a cryptographic module authenticates the authorization of an operator to assume a specific role and perform a corresponding set of services Figure 4 Example of FIPS tamper evidence labels For reference only May not represent actual drive SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C 16 5 0 SERIAL ATA SATA INTERFACE These drives use the industry standard Serial ATA interface that supports FIS data transfers It supports ATA programmed input output PIO modes 0 4 multiword DMA modes 0 2 and Ultra DMA modes 0 6 The drive also supports the use of the IORDY signal to provide reliable high speed data transfers For detailed information about the Serial ATA interface refer to the Serial ATA High Speed Serialized AT Attachment specification 5 1 HoT PLUG COMPATIBILITY Seagate Laptop SSHD SATA drives incorporate connectors which enable you to hot plug these drives in accordance with the Serial ATA High Speed Serialized AT Attachment specification revision 2 0 This specification can be downloaded from www serialata org This device requires a COMRESET from the host after a hotplug event 5 2 SERIAL ATA DEVICE PLUG CONNECTOR PIN DEFINITIONS Table 8 summarizes the signals on the Serial ATA interface and power connectors Refer to the Notes below Table 8 Serial ATA Connec
7. 16 48 Trusted Computing Feature set options 00004 49 Standard Standby timer IORDY supported and may be disabled 2F00y 50 Capabilities 40004 51 PIO data transfer cycle timing mode 02004 52 Retired 02004 53 Words 54 58 64 70 and 88 are valid 0007H 54 Number of current logical cylinders XXXXH 55 Number of current logical heads XXXXH 56 Number of current logical sectors per logical track XXXXH 57 58 Current capacity in sectors XXXXH 59 Number of sectors transferred during a XXXXH Read Multiple or Write Multiple command SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C 20 SERIAL ATA SATA INTERFACE Table 10 Identify Device command Word Description Value 60 61 Total number of user addressable sectors ST1000LM014 OFFFFFFFh This field contains a value that is one greater than the total number ST1000LM015 OFFFFFFFh of ST1000LM028 OFFFFFFFh user addressable sectors The maximum value that shall be placed ST750LMO000 OFFFFFFFh in this field is OFFFFFFFh The OFFFFFFFh value applies to all capacities over 137GB see Section 2 1 for related information 62 Retired 00004 63 Multiword DMA active and modes supported xXx07 y see note following this table 64 Advanced PIO modes supported modes 3 and 4 supported 00034 65 Minimum multiword DMA transfer cycle time per word 120 ns 0078 66 Recommended multiword DMA transfer cycle time per word 120 ns 0078y
8. 5 CE mark 12 certification 12 Check Power Mode 19 China RoHS directive 13 compatibility 12 conducted noise 8 conducted RF immunity 11 configuring and mounting the drive 14 connectors 14 corrosive environment 13 CSA60950 1 12 D DC power 7 density 6 Device Configuration Freeze Lock 18 Device Configuration Restore 18 Device Configuration Set 18 Diagnostics 18 dimensions 15 dissipation 7 Download Microcode 18 E electrical fast transient 11 Electromagnetic Compatibility EMC 12 Electromagnetic Compatibility control Regulation 12 Electromagnetic Compatibility Directive 2004 108 EC 12 electromagnetic immunity 11 electrostatic discharge ESD 11 14 EN 55022 ClassB 12 EN 55024 12 EN60950 12 enclosures 12 environmental specifications 9 SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C INDEX errors 11 ESD 14 EU 12 EU RoHS directive 13 European Union EU requirements 12 evice Configuration Identify 18 Execute Device Diagnostics 18 F FCC verification 12 features 2 Federal Information Processing Standard 16 FIPS 16 Flush Cache 18 Flush Cache Extended 18 formatted capacity 5 Freeze Lock 18 G Gs acceleration of gravity 10 guaranteed sectors 5 H handling precautions 14 height 6 I O data transfer rate 6 Identify 18 Identify Device 18 Identify Device command 20 Idle 19 Idle Immediate 19 idle mode 7 9 idle performance 7 Information Technology Equipment ITE 12 Initi
9. California 95014 United States 408 658 1000 ASIA PACIFIC Seagate Singapore International Headquarters Pte Ltd 7000 Ang Mo Kio Avenue 5 Singapore 569877 65 6485 3888 EUROPE MIDDLE EAST AND AFRICA Seagate Technology SAS 16 18 rue du D me 92100 Boulogne Billancourt France 33 1 4186 10 00 Publication Number 100716627 Rev C June 2013
10. and Control Block registers PIO and DMA data transfers resets and interrupts are all emulated The Serial ATA host adapter contains a set of registers that shadow the contents of the traditional device registers referred to as the Shadow Register Block All Serial ATA devices behave like Device 0 devices For additional information about how Serial ATA emulates parallel ATA refer to the Serial ATA International Organization Serial ATA Revision 3 0 The specification can be downloaded from www serialata org SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C 3 2 0 DRIVE SPECIFICATIONS DRIVE SPECIFICATIONS Unless otherwise noted all specifications are measured under ambient conditions at 25 C and nominal power For convenience the phrases the drive and this drive are used throughout this manual to indicate the following drive models The specification summaries listed in the following tables are for quick reference For details on specification measurement or definition refer to the appropriate section of this manual Table 1 Drive Specifications Summary DRIVE SPECIFICATION Formatted capacity 1 Guaranteed sectors ST1000LM014 ST1000LM015 AND ST1000LM028 ST750LM000 750 GB 1 953 525 168 1 465 149 168 Heads Bytes per sector 4 512 logical 4096 physical NAND flash Commercial Multilevel Cell CMLC 8GB Recording density Track density 1894 Kb in 375 Ktracks in avg Areal densi
11. may apply below 22 Hz 2 9 ACOUSTICS Drive emission of sound is measured consistent with the ECMA 74 and its referenced standards Testing is conducted at room temperature approximately 25 C Emission levels are reported as the total A weighted sound power levers for steady state idle and active seeks modes of operation Table 6 Drive A weighted Sound Power Levels SWL BA 2 2 bels typ 2 4 bels typ 2 4 bels max 2 6 bels max 1 During periods of drive idle some offline activity may occur according to the S M A R T specification which may increase acoustic and power to operational levels 2 9 1 Test for prominent discrete tones PDTs Seagate follows the ECMA 74 standards for measurement and identification of PDTs An exception to this process is the use of the absolute threshold of hearing Seagate uses the lower limit for the threshold curve to discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone ratios according to Annex D of the ECMA 74 standards Defined as the median curve given by ISO 389 7 Tf curve minus 10dB at all frequencies SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C 10 2 10 ELECTROMAGNETIC IMMUNITY When properly installed in a representative host system the drive operates without errors or degradation in performance when subjected to the radio frequency RF environment as defined in Table 7 Table 7 Radio Frequency Environments
12. words 60 61 and 100 103 for additional information about 48 bit addressing support of drives with capacities over 137 GB 2 2 PHYSICAL ORGANIZATION Drive model Read write heads Number of discs ST1000LM014 ST1000LM015 and ST1000LM028 4 2 ST750LM000 SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C 5 DRIVE SPECIFICATIONS 2 3 RECORDING AND INTERFACE TECHNOLOGY Interface Serial ATA SATA Recording method Perpendicular Recording density 1894 Kb in Track density 375 ktracks in avg Areal density 705 Gb in avg Spindle speed 5400 RPM 0 2 Sustained data transfer rate 100 MB s max I O data transfer rate 600 MB s max 2 4 PHYSICAL CHARACTERISTICS Height 9 5 0 2 mm 0 374 008 in Width 69 85 0 25 mm 2 750 0 010 in All models Length 100 35 0 20 0 25 mm 3 951 0 008 0 010 in Typical weight 115 g 0 254 lb Cache buffer 64MB 65 536 KB 2 5 SEEK TIME Seek measurements are taken with nominal power at 25 C ambient temperature All times are measured using drive diagnostics The specifications in the table below are defined as follows m Track to track seek time is an average of all possible single track seeks in both directions m Average seek time is a true statistical random average of at least 5000 measurements of seeks between random tracks less overhead Table 2 Typical seek times Read 2 0 12 0 5 6 Typical seek times ms Track to tr
13. 40 2 is a U S government computer security standard used to accredit cryptographic modules It is titled Security Requirements for Cryptographic Modules The initial publication was on May 25 2001 and was last updated December 3 2002 Purpose The National Institute of Standards and Technology NIST issued the FIPS 140 Publication Series to coordinate the requirements and standards for cryptography modules that include both hardware and software components Federal Information Processing Standard FIPS 140 2 Level 2 Certification requires drives to go through government agencies certifications to add requirements for physical tamper evidence and role based authentication For more information refer to Security Rules section in the Security Policy document uploaded on the NIST website To reference the product certification visit http csrc nist gov groups STM cmvp documents 140 1 1401vend htm and search for Seagate Security Level 2 Security Level 2 enhances the physical security mechanisms of a Security Level 1 cryptographic module by adding the requirement for tamper evidence which includes the use of tamper evident coatings or seals on removable covers of the module Tamper evident coatings or seals are placed on a cryptographic module so that the coating or seal must be broken to attain physical access to the critical security parameters CSP within the module Tamper evident seals example shown in Figure 5 page 19
14. Gs Vibration operating 201 500 Hz 1 0 Gs Vibration nonoperating 5 500 Hz 5 0 Gs Nonrecoverable read errors 1 per 107 bits read To determine the warranty for a specific drive use a web browser to access the following web page http www seagate com support warranty and replacements Warranty From this page click on the Verify Your Warranty link You will be asked to provide the drive serial number model number or part number and country of purchase The system will display the warranty information for your drive Load unload cycles 600 000 at 25 C 50 rel humidity Supports Hotplug operation per the Serial ATA Revision 2 6 specification a 1 One GB equals one billion bytes when referring to hard drive capacity Accessible capacity may vary depending on operating environment and formatting 2 1 FORMATTED CAPACITY MODEL FORMATTED Capacity GUARANTEED SECTORS BYTES PER SECTOR ST1000LM014 ST1000LM015 1000 GB 1 953 525 168 STI DES 512 logical 4096 physical ST750LM000 750 GB 1 465 149 168 1 One GB equals one billion bytes when referring to hard drive capacity Accessible capacity may vary depending on operating environment and formatting 2 1 1 LBA mode When addressing these drives in LBA mode all blocks sectors are consecutively numbered from 0 to n 7 where nis the number of guaranteed sectors as defined above Refer to Configuring and Mounting the Drive on page 14
15. Seagate Product Manual Seagate Laptop SSHD Standard models Self Encrypting Drive models ST1000LM014 ST1000LM015 ST750LMO000 SED FIPS 140 2 models ST1000LM028 Gen 1 100716627 Rev C June 2013 Document Revision History Revision Date Description of Change Rev A 01 08 2013 Initial release Rev B 05 01 2013 fc 1 2 4 5 11 16 amp 19 21 Rev C 06 05 2013 7 O 2013 Seagate Technology LLC All rights reserved Publication number 100716627 Rev C June 2013 Seagate Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and or other countries Seagate Laptop SSHD and SeaTools are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and or other countries The FIPS logo is a certification mark of NIST which does not imply product endorsement by NIST the U S or Canadian governments All other trademarks or registered trademarks are the property of their respective owners No part of this publication may be reproduced in any form without written permission of Seagate Technology LLC Call 877 PUB TEK1 877 782 8351 to request permission When referring to drive capacity one gigabyte or GB equals one billion bytes and one terabyte or TB equals one trillion bytes Your computer s operating system may use a different standard of measurement and report a lower capac
16. TING eae ge Sale aidan tee Raid ede ee se ea en Sed 15 4 0 ABOUT FIPS o crio ck so tate ewan Nai aad 16 5 0 SERIAL ATA SATA INTERFACE 2 0 0 e eee ee eee eee eee eee eee 17 5 1 HOT PLUG COMPATIBILITY atado ears Dante alae aha RER REE Sond 17 5 2 SERIAL ATA DEVICE PLUG CONNECTOR PIN DEFINITIONS 0 000 e eee eens 17 5 3 SUPPORTED ATA COMMANDS 00 cece cee teen e eens 18 5 3 1 Identify Device COMMANd ooocccccc nanana annann 20 5 3 2 Set Features COMMAN esceas ad taa ia 24 5 3 3 SMART COMMANQOS o ooccoo tee eens 25 SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL Rev C III FIGURES FIGURE 1 TYPICAL 5V STARTUP AND OPERATION CURRENT PROFILE 0 0000 ee eee eee eee 8 FIGURE 2 ATTACHING SATA CABLING oa A SA das 14 FIGURE 3 MOUNTING DIMENSIONS FOR STANDARD MODELS 0000 e cece eee eee eee eens 15 FIGURE 4 EXAMPLE OF FIPS TAMPER EVIDENCE LABELS 0 0000 cece eee eee eee eee eee 16 SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C Seagate Technology Support Services For information regarding online support and services visit_http www seagate com about contact us technical support Available services include e Presales amp Technical support e Global Support Services telephone numbers amp business hours Authorized Service Centers For information regarding Warranty Support visit http www seagate com support warranty and replacements For information regarding data recovery
17. ack Average Average latency These drives are designed to consistently meet the seek times represented in this manual Physical seeks regardless of mode such as track to track and average are expected to meet the noted values However due to the manner in which these drives are formatted benchmark tests that include command overhead or measure logical seeks may produce results that vary from these specifications 2 6 START STOP TIMES Table 3 Start stop times Typical seek times ms Max 25 C Power on to ready sec lt 1 0 Power on to ready sec SED models TBD Standby to ready sec lt 1 0 SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C 6 DRIVE SPECIFICATIONS 2 7 POWER SPECIFICATIONS The drive receives DC power 5V through a native SATA power connector refer to Figure 2 2 7 1 Power consumption Power requirements for the drives are listed in the table in Table 4 Typical power measurements are based on an average of drives tested under nominal conditions at 25 C ambient temperature These power measurements are done with Interface Power Management modes like HIPM and DIPM enabled Spinup power Spinup power is measured from the time of power on to the time that the drive spindle reaches operating speed Seek mode During seek mode the read write actuator arm moves toward a specific position on the disk surface and does not execute a read or write operation Servo electronics are active Seek
18. alize Device Parameters 18 input noise ripple 8 interface 17 interference 12 ITE 12 K KCC 12 Korean Communications Commission 12 Korean Radio Research Laboratory RRL 12 L LBA mode 5 length 6 master slave 3 Max Address 18 26 Microcode 18 mounting 15 N National Institute of Standards and Technology 16 NIST 16 noise 8 nominal power 6 nonoperating shock 10 nonoperating vibration 10 nonrecoverable read errors 11 O operating shock 10 operating vibration 10 P physical characteristics 6 Physical organization 5 point to point 3 14 power consumption 7 power dissipation 7 power management modes 9 power modes 9 power specifications 7 precautions 14 printed circuit board 14 programmable power management 9 prominent discrete tone 10 Q quick reference 4 R Radiated RF immunity 11 radio and television interference 12 radio frequency RF 11 random track location 7 Read Buffer 18 Read DMA 18 Read DMA Extended 18 Read DMA without Retries 18 read errors 11 Read Long with Retries 18 Read Long without Retries 18 Read Multiple 18 Read Multiple Extended 18 Read Native Max Address 18 Read Native Max Address Extended 18 Read Sectors 18 Read Sectors Extended 18 Read Sectors without Retries 18 Read Verify Sectors 18 Read Verify Sectors Extended 18 Read Verify Sectors without Retries 18 SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL Rev C INDEX read write power 7 recording de
19. ative Command Queuing NCQ with command ordering Full track multiple sector transfer capability without local processor intervention 1000 Gs nonoperating shock and 350 Gs of operating shock SeaTools diagnostic software performs a drive self test that eliminates unnecessary drive returns The 3D Defense System which includes Drive Defense Data Defense and Diagnostic Defense offers the industry s most comprehensive protection for disk drives Support for S M A R T drive monitoring and reporting Support for Read Multiple and Write Multiple commands Worldwide Name WWN capability uniquely identifies the drive Seagate Laptop SSHD Self Encrypting Drive models have the following additional features Automatic data encryption decryption Controlled access Random number generator Drive locking 16 independent data bands Cryptographic erase of user data for a drive that will be repurposed or scrapped Authenticated firmware download There is no significant performance difference between Self Encrypting Drive and standard non Self Encrypting Drive models SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C 1 1 BOUT THE SERIAL ATA INTERFACE The Serial ATA interface provides several advantages over the traditional parallel ATA interface The primary advantages include m Easy installation and configuration with true plug and play connectivity It is not necessary to set any jumpers or other configuration options m Thi
20. by the China RoHS MCV Standard BA FRAMES ME fee AR EA E h H EI RoHS MCV ave PAE QAI ME 2 14 CORROSIVE ENVIRONMENT Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments containing sulfurous gases chlorine and nitric oxide classes G and H per ASTM B845 However this accelerated testing cannot duplicate every potential application environment Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive chemicals as electronic drive component reliability can be affected by the installation environment The silver copper nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide chloride and nitrate contaminants Sulfur is found to be the most damaging In addition electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly PCBA or exposed to an ambient relative humidity greater than 95 Materials used in cabinet fabrication such as vulcanized rubber that can outgas corrosive compounds should be minimized or eliminated The useful life of any electronic equipment may be extended by replacing materials near circuitry with sulfide free alternatives SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C 13 CONFIGURING AND MOUNTING THE DRIVE 3 0 CONFIGURING AND MOUNTING THE DRIVE This section contains the specificatio
21. ce command SERIAL ATA SATA INTERFACE The Identify Device command command code ECy transfers information about the drive to the host following power up The data is organized as a single 512 byte block of data whose contents are shown in Table 10 All reserved bits or words should be set to zero Parameters listed with an x are drive specific or vary with the state of the drive Refer to Drive Specifications on page 4 for default parameter settings The following commands contain drive specific features that may not be included in the Serial ATA specification Table 10 Identify Device command Word Description Value Configuration information OC5Ay Bit 15 0 ATA 1 ATAPI 0 Bit 7 removable media Bit 6 removable controller Bit 0 reserved 1 Number of logical cylinders 16 383 2 Specific configuration C837H 3 Number of logical heads 16 4 Retired 00004 5 Retired 00004 6 Number of logical sectors per logical track 63 003F y 7 9 Retired 00004 10 19 Serial number 20 ASCII characters 00004 none ASCII 20 Retired 00004 21 Retired 80004 22 Obsolete 00044 23 26 Firmware revision X XX 8 ASCII character string padded with blanks to end of string 27 46 Drive model number ST1000LM014 40 ASCII characters padded with blanks to end of string ST1000LM015 ST1000LM028 ST750LMO000 47 Bits 7 0 80104 Maximum sectors per interrupt on Read multiple and Write multiple
22. ch drive is considered a master in a point to point relationships If two drives are attached on one Serial ATA host adapter the host operating system views the two devices as if they were both masters on two separate ports Both drives behave as if they are Device 0 master devices 3 2 1 Serial ATA Cables and Connectors The Serial ATA interface cable consists of four conductors in two differential pairs plus three ground connections The cable size may be 30 to 26 AWG with a maximum length of one meter 39 37 in Refer to Table 8 for connector pin definitions Either end of the SATA signal cable can be attached to the drive or host For direct backplane connection the drive connectors are inserted directly into the host receptacle The drive and the host receptacle incorporate features that enable the direct connection to be hot pluggable and blind mateable For installations which require cables you can connect the drive as shown in Figure 2 Figure 2 Attaching SATA Cabling Signal connector Power connector Signal cable Power cable Each cable is keyed to ensure correct orientation Seagate Laptop SSHD SATA drives support latching SATA connectors SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C 14 3 3 DRIVE MOUNTING You can mount the drive in any orientation using four screws in the side mounting holes or four screws in the bottom mounting holes Refer to Figure 3 for drive mounting dimensions Follow these importan
23. continued BIT WORD 88 Ultra DMA mode 0 is supported Ultra DMA mode 1 is supported Ultra DMA mode 2 is supported Ultra DMA mode 3 is supported Ultra DMA mode 4 is supported Ultra DMA mode 5 is supported Ultra DMA mode 6 is supported Ultra DMA mode 0 is currently active Ultra DMA mode 1 is currently active Ultra DMA mode 2 is currently active Ultra DMA mode 3 is currently active Ultra DMA mode 4 is currently active 13 Ultra DMA mode 5 is currently active 14 Ultra DMA mode 6 is currently active Bit WORD 93 13 1 80 conductor cable detected CBLID above VIH 0 40 conductor cable detected CBLID below VIL SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C SERIAL ATA SATA INTERFACE 23 SERIAL ATA SATA INTERFACE 5 3 2 Set Features command This command controls the implementation of various features that the drive supports When the drive receives this command it sets BSY checks the contents of the Features register clears BSY and generates an interrupt If the value in the register does not represent a feature that the drive supports the command is aborted Power on default has the read look ahead and write caching features enabled The acceptable values for the Features register are defined as follows Table 12 Set Features command values 024 Enable write cache default 034 Set transfer mode based on value in Sector Count register
24. dress ST1000LM028 1 953 525 168 ing ST750LM000 1 465 149 168 feature Maximum value OOOOFFFFFFFFFFFFh 104 Streaming Transfer Time PIO 0000 105 Reserved 00004 106 Physical sector size Logical sector size 60034 107 Seagate reserved 0000 108 111 The mandatory value of the world wide name WWN for the drive Each drive will have a unique value NOTE This field is valid if word 84 bit 8 is set to 1 indicating 64 bit WWN support 112 118 ATA reserved 0000y 119 Free Fall Protection support bit 5 1 Free Fall Protection supported 0 Free Fall Protection not supported 120 Free Fall Protection enable disable bit 5 1 Free Fall Protection feature is enabled 0 Free Fall Protection feature is dis abled 121 ATA reserved 00004 127 128 Security status 00214 129 Seagate reserved XXXXH 159 160 ATA reserved 0000H 221 222 Transport major version number 101Fy 223 ATA reserved 00004 254 255 Integrity word XXA5SH NOE See the bit descriptions below for words 63 88 and 93 of the Identify Drive data Table 11 Bit Descriptions Description if bit is set to 1 WORD 63 Multiword DMA mode 0 is supported Multiword DMA mode 1 is supported Multiword DMA mode 2 is supported Multiword DMA mode 0 is currently active Multiword DMA mode 1 is currently active Multiword DMA mode 2 is currently active SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C 22 Table 11 Bit Descriptions
25. e the Draft ATA 5 Standard SeaTools diagnostic software activates a built in drive self test DST S M A R T command for D44 that eliminates unnecessary drive returns The diagnostic software ships with all new drives and is also available at http www seagate com support downloads seatools This drive is shipped with S M A R T features disabled You must have a recent BIOS or software package that supports S M A R T to enable this feature The table below shows the S M A R T command codes that the drive uses Table 13 S M A R T Commands CODE IN FEATURES REGISTER S M A R T COMMAND D0y S M A R T Read Data D2y S M A R T Enable Disable Attribute Autosave D3y S M A R T Save Attribute Values D4y S M A R T Execute Off line Immediate runs DST DSy S M A R T Read Log Sector D6y S M A R T Write Log Sector D8y S M A R T Enable Operations D9y S M A R T Disable Operations DAy S M A R T Return Status If an appropriate code is not written to the Features Register the command is aborted and 0x04 abort is written to the Error register SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C 25 A acoustics 10 active mode 9 Address 18 agency certification 12 ambient temperature 6 areal density 6 ATAcommands 18 Australia New Zealand Standard AS NZS3548 1995 12 Australian Communication Authority ACA 12 Australian C Tick 12 Average seek time 6 B buffer 6 C cables and connectors 14 capacity
26. h low power Active mode The drive is in active mode during the read write and seek operations Idle mode The buffer remains enabled and the drive accepts all commands and returns to active mode any time disk access is necessary Standby mode The drive enters standby mode when the host sends a standby Immediate command If the host has set the standby timer the drive can also enter standby mode automatically after the drive has been inactive for a specifiable length of time The standby timer delay is established using a standby or idle command In standby mode the drive buffer is enabled the heads are parked and the spindle is at rest The drive accepts all commands and returns to active mode any time disk access is necessary Sleep mode The drive enters sleep mode after receiving a sleep command from the host In sleep mode the drive buffer is disabled the heads are parked and the spindle is at rest The drive leaves sleep mode after it receives a hard reset or soft reset from the host After receiving a reset the drive exits sleep mode and enters standby mode with all current translation parameters intact Idle and standby timers Each time the drive performs an active function read write or seek the standby timer is reinitialized and begins counting down from its specified delay times to zero If the standby timer reaches zero before any drive activity is required the drive makes a transition to standby mode In both Idle a
27. interference This equipment generates and uses radio frequency energy and if not installed and used in strict accordance with the manufacturer s instructions may cause interference to radio and television reception This equipment is designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television which can be determined by turning the equipment on and off you are encouraged to try one or more of the following corrective measures m Reorient the receiving antenna Move the device to one side or the other of the radio or TV Move the device farther away from the radio or TV Plug the computer into a different outlet so that the receiver and computer are on different branch outlets If necessary you should consult your dealer or an experienced radio television technician for additional suggestions You may find helpful the following booklet prepared by the Federal Communications Commission How to Identify and Resolve Radio Television Interference Problems This booklet is available from the Superintendent of Documents U S Government Printing Office Washington DC 20402 Refer to publication number 004 000 00345 4 SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C 12 DRIVE SPECIFICATIONS 2 13 ENVIRONMENTAL PROTECTION Seagate designs its products to mee
28. ith the performance levels specified in this document when subjected to a maximum operating shock of 350 Gs based on half sine shock pulses of 2ms Shocks should not be repeated more than one time per axis 2 8 1 2 Nonoperating shock The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 800 Gs based on a nonrepetitive half sine shock pulse of 2 ms duration The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 1000 Gs based on a nonrepetitive half sine shock pulse of 1 ms duration 28 2 Vibration All vibration specifications assume that the drive is mounted securely with the input vibration applied at the drive mounting screws Vibration may be applied in the X Y or Z axis 2 8 2 1 Operating vibration The maximum vibration levels that the drive may experience while meeting the performance standards specified in this document are specified below 5 200 Hz 2 0 Gs 0 to peak Max displacement may apply below 10 Hz 201 500 Hz 1 0 Gs 0 to peak 2 8 2 2 Nonoperating vibration The maximum nonoperating vibration levels that the drive may experience without incurring physical damage or degradation in performance when subsequently put into operation are specified below 5 500 Hz 5 0 Gs 0 to peak Max displacement
29. ity In addition some of the listed capacity is used for formatting and other functions and thus will not be available for data storage Actual quantities will vary based on various factors including file size file format features and application software Actual data rates may vary depending on operating environment and other factors The export or re export of hardware or software containing encryption may be regulated by the U S Department of Commerce Bureau of Industry and Security for more information visit www bis doc gov and controlled for import and use outside of the U S Seagate reserves the right to change without notice product offerings or specifications CONTENTS SEAGATE TECHNOLOGY SUPPORT SERVICES 2 00 cece ee eee 1 1 0 INTRODUCTION 623 see hee iia Ss deed A i Dee ee eed bee 2 1 1 ABOUT THE SERIAL ATA INTERFACE 0 000 cee eee ek k nere kkn 3 2 0 DRIVE SPECIFICATIONS n oana dn a oe ie Ak dees dead eee bo beret ge ee 4 2 1 FORMATTED CAPACITY rope RS aide tarhsewa a a 5 2 1 1 BA Modest rd os BRS eect Na cs was SA GSR ears 5 2 2 PHYSICAL ORGANIZATION 2 aller eee e dels mad beac dale nb oad ned Hale das woes 5 2 3 RECORDING AND INTERFACE TECHNOLOGY 0000 c cece eee ene nee eens 6 2 4 PHYSICAL CHARACTERISTICS ri oid Sas ae ea a ee ENG Weed a taal edb eda 6 2 5 SEE TIMES LOCO aa DAS Mast anemia d 6 2 6 STARTSTOP TIMES sokar a ae A A da ta 6 2 7 POWER SPECIFICATIONS senie ber teenie tenet ene ee
30. max C2 P2 max C3 P3 P4 P5 P6 value 116 mA 956 mA mean 116 1 mA 955 8 mA min 116 mA 956 mA max 116 mA 956 mA sdev num 1 1 status Y Y 2 7 2 Conducted noise Trigger Roll 1 00 sidiv Stop 1 00MS 100 kS s X1 6 499985 AX 0 00 ms X2 6 499985 1IAX 1 2 2013 5 29 25 PM Input noise ripple is measured at the host system power supply across an equivalent 15 ohm resistive load on the 5 volt line m Using 5 volt power the drive is expected to operate with a maximum of 100 mV peak to peak square wave injected noise at up to 10 MHz NOTE Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read write current 2 7 3 Voltage tolerance Voltage tolerance including noise m 5V 45 SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C DRIVE SPECIFICATIONS 2 7 4 Power management modes The drive provides programmable power management to provide greater energy efficiency In most systems power management is controlled through the system setup program The drive features the following power management modes POWER MODES HEADS SPINDLE BUFFER Active operating Tracking Rotating Full power Idle performance Tracking Rotating Self refresh low power Idle active Floating Rotating Self refresh low power Idle low power Parked Rotating Self refresh low power Standby Parked Stopped Self refresh low power Sleep Parked Stopped Self refres
31. mode power is measured based on three random seek operations every 100 ms This mode is not typical Read write power and current Read write power is measured with the heads on track based on three 63 sector read or write operations every 100 ms m Idle mode power Idle mode power is measured with the drive up to speed with servo electronics active and with the heads in a random track location Standby mode During standby mode the drive accepts commands but the drive is not spinning and the servo and read write electronics are in power down mode Table 4 DC Power Requirements POWER DISSIPATION 5V INPUT AVERAGE 25 C Spinup max lt 1 20A Seek average 2 7W Write average 3 7W Read average 3 1W Idle performance 0 2 2W Idle active 1 1W Idle low power mode 0 9W Standby 0 53W Sleep 0 53W da During periods of drive idle some offline activity may occur according to the S M A R T specification which may increase acoustic and power to operational levels 2 Standby power is measured at steady state after 200ms from transition SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C 7 2 7 1 1 Typical current profiles DRIVE SPECIFICATIONS The typical 5V startup and operation current profile is shown in Figure 1 Figure 1 Typical 5V Startup and Operation Current Profile File Vertical Trigger Display Cur Math Analysis Utilities Help a Measure P1
32. nd standby mode the drive accepts all commands and returns to active mode when disk access is necessary 2 8 ENVIRONMENTAL SPECIFICATIONS This section provides the temperature humidity shock and vibration specifications for Seagate Laptop SSHD drives Ambient temperature is defined as the temperature of the environment immediately surrounding the drive Above 1000 feet 305 meters the maximum temperature is derated linearly by 1 C every 1000 feet Table 5 Environmental specifications Parameters Operating Non Operating Ambient temperature 0 to 60 C 32 to 140 F 40 to 70 C 40 to 158 F 20 C per hour 68 F per hour max 35 C per hour 95 F per hour max Temperature gradient without condensation without condensation 5 to 95 non condensing 5 to 95 non condensing Humidity 30 per hour 30 per hour Wet bulb 37 7 C 99 8 F max 40 C 104 F max 304 8m to 3048m 304 8m to 12 192m Altitude 1000ft to 10 000ft 1000ft to 40 000ft The recommended storage period 1 year under controlled conditions of 34 C 90 RH or less e 90 days in uncontrolled storage conditions SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C 9 DRIVE SPECIFICATIONS 2 8 1 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws Shock may be applied in the X Y or Z axis 2 8 1 1 Operating shock These drives comply w
33. ndard commands that the drive supports For a detailed description of the ATA commands refer to the Serial ATA International Organization Serial ATA Revision 2 6 Refer to www sata io org Refer to S M A R T commands on page 25 for details and subcommands used in the S M A R T implementation Table 9 Supported ATA commands ATA standard commands names Command code in hex Device Configuration Restore B1h COh Device Configuration Freeze Lock B1h C1h Device Configuration Identify B1h C2h Device Configuration Set B1h C3h Download Microcode 92h Execute Device Diagnostics 90h Flush Cache E7h Flush Cache Extended EAh Identify Device ECh Initialize Device Parameters 91h Read Buffer E4h Read DMA C8h Read DMA Extended 25h Read DMA without Retries C9h Read Long with Retries 22h Read Long without Retries 23h Read Multiple C4h Read Multiple Extended 29h Read Native Max Address F8h Read Native Max Address Extended 27h Read Sectors 20h Read Sectors Extended 24h Read Sectors without Retries 21h Read Verify Sectors 40h Read Verify Sectors Extended 42h Read Verify Sectors without Retries 41h Seek 70h Set Features EFh Set Max Address F9h Note Individual Set Max commands are identified by the Address value placed in the Set Max Features register as defined to Password the right Lock Unlock Set Max Address Ext SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C Freeze Lock 37h
34. nner and more flexible cabling for improved enclosure airflow and ease of installation Scalability to higher performance levels In addition Serial ATA makes the transition from parallel ATA easy by providing legacy software support Serial ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disk drive in your current system and expect all of your existing applications to work as normal The Serial ATA interface connects each disk drive in a point to point configuration with the Serial ATA host adapter There is no master slave relationship with Serial ATA devices like there is with parallel ATA If two drives are attached on one Serial ATA host adapter the host operating system views the two devices as if they were both masters on two separate ports This essentially means both drives behave as if they are Device 0 master devices The host adapter may optionally emulate a master slave environment to host software where two devices on separate Serial ATA ports are represented to host software as a Device 0 master and Device 1 slave accessed at the same set of host bus addresses A host adapter that emulates a master slave environment manages two sets of shadow registers This is not a typical Serial ATA environment The Serial ATA host adapter and drive share the function of emulating parallel ATA device behavior to provide backward compatibility with existing host systems and software The Command
35. ns 7 2 7 1 Power CONSUMPTION se ne sterke pee te a ya 7 2 7 2 GOnGUCIEd NOISE iio A AS eae 8 2 7 3 Voltage tolerance e Ten FA as aed thongs Sede Cha pew tee Oke 8 2 7 4 Power management ModesS oocccccco eee 9 2 8 ENVIRONMENTAL SPECIFICATIONS irsk ONETARA EPERE ene ee ene eens 9 2 8 1 MOCK OR 10 2 8 2 MIDFATION ee ah dest weet eed A ar went wh sa laser connie pee 10 2 9 ACOUSTICS ia at Cane avin awed Gat desta 10 2 9 1 Test for prominent discrete tones PDTS 0 00 eee eee 10 2 10 ELECTROMAGNETIC IMMUNITY sie ERE ene ee tenes 11 2 11 RELIABILITY sce 2 at A A A VIA A ek ara ee AR 11 2 12 AGENCY CERTIFICATION 0 00 ccc ce teen ten eee een eee 12 2 121 Safety certification ooooocoooocccrnnaorra 12 2 12 2 Electromagnetic Compatibility EMC 00 00 eee 12 2 12 33 FOO ventiGation 13 sss aaa lada 12 2 13 ENVIRONMENTAL PROTECTION ansas ccc cece eee een teen eee 13 2 13 1 European Union Restriction of Hazardous Substances RoHS Directive 13 2 13 2 China Restriction of Hazardous Substances RoHS Directive 13 2 14 CORROSIVE ENVIRONMENT nc cedidas aida ade a id weed ath wed awed 13 3 0 CONFIGURING AND MOUNTING THE DRIVE 020 eee eee eee eee 14 3 1 HANDLING AND STATIC DISCHARGE PRECAUTIONS 0000 cece eee eee tenn 14 3 2 CONFIGURING THE DRIVE 0 cc eee eens 14 3 2 1 Serial ATA Cables and Connectors 0 0 0 cece eee 14 3 3 DRIVE MOUN
36. ns and instructions for configuring and mounting the drive 3 1 HANDLING AND STATIC DISCHARGE PRECAUTIONS After unpacking and before installation the drive may be exposed to potential handling and electrostatic discharge ESD hazards Observe the following standard handling and static discharge precautions Keep the drive in the electrostatic discharge ESD bag until you are ready for installation to limit the drive s exposure to ESD e Before handling the drive put on a grounded wrist strap or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet Wear a grounded wrist strap throughout the entire installation procedure Handle the drive by its edges or frame only The drive is extremely fragile handle it with care Do not press down on the drive top cover Always rest the drive on a padded antistatic surface until you mount it in the computer Do not touch the connector pins or the printed circuit board Do not remove the factory installed labels from the drive or cover them with additional labels Removal voids the warranty Some factory installed labels contain information needed to service the drive Other labels are used to seal out dirt and contamination CAUTION 3 2 CONFIGURING THE DRIVE Each drive on the Serial ATA interface connects in a point to point configuration with the Serial ATA host adapter There is no master slave relationship because ea
37. nsity 6 recording method 6 recording technology 6 reliability 11 Retries 18 RMS read write current 8 RoHS 13 RRL 12 S S M A R T 19 S M A R T implementation 18 safety certification 12 SATA ports 3 screws 15 Seagate Technology Support Services 1 sectors 5 Security Disable Password 19 Security Erase Prepare 19 Security Erase Unit 19 Security Freeze Lock 19 Security Set Password 19 Security Unlock 19 Seek 18 seek mode 7 Seek time 6 seek time 7 Self refresh low power 9 Serial ATA SATA interface 17 Set Features 18 Set Max Address 18 Set Multiple Mode 19 shock 10 single track seeks 6 Sleep 19 sleep 7 sleep mode 9 spindle speed 6 spinup DC power 7 spinup power 7 Standby 19 standby 7 Standby Immediate 19 standby mode 7 9 standby timer 9 Start stop times 7 static discharge 14 subassembly 12 surge immunity 11 T temperature 6 timers Idle and Standby 9 track density 6 Track to track seek time 6 27 Transport major version number 22 U UL60950 1 12 V vibration 10 voltage dips interrupts 11 voltage tolerance 8 W warranty 11 weight 6 width 6 Write Buffer 19 Write DMA 19 Write DMA Extended 19 Write Long with Retries 19 Write Long without Retries 19 Write Multiple 19 Write Sectors 19 SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C 28 Seagate Seagate Technology LLC AMERICAS Seagate Technology LLC 10200 South De Anza Boulevard Cupertino
38. on Republic of Korea These drives have been tested and comply with the Electromagnetic Interference Electromagnetic Susceptibility EMI EMS for Class B products Drives are tested in a representative end user system by a Korean recognized lab Certificate number IKCC REM STX LaptopSSHD m Trade name or applicant Seagate Technology LLC Certificate date 14 December 2012 Manufacturer nationality USA Singapore and China Australian C Tick N176 If these models have the C Tick marking they comply with the Australia New Zealand Standard AS NZS3548 1995 and meet the Electromagnetic Compatibility EMC Framework requirements of the Australian Communication Authority ACA 2 12 3 FCC verification These drives are intended to be contained solely within a personal computer or similar enclosure not attached as an external device As such each drive is considered to be a subassembly even when it is individually marketed to the customer As a subassembly no Federal Communications Commission verification or certification of the device is required Seagate has tested this device in enclosures as described above to ensure that the total assembly enclosure disk drive motherboard power supply etc does comply with the limits for a Class B computing device pursuant to Subpart J Part 15 of the FCC rules Operation with noncertified assemblies is likely to result in interference to radio and television reception Radio and television
39. services visit http www seagate com services software data recovery services For Seagate OEM and Distribution partner portal visit http www seagate com partners For Seagate reseller portal visit http www seagate com partners my spp dashboard Seagate Laptop SSHD SATA Product Manual Rev C 1 1 0 INTRODUCTION This manual describes the functional mechanical and interface specifications for the following Seagate Seagate Laptop SSHD model drives Standard models Standard SED models SED FIPS 140 2 models ST1000LM014 ST1000LM015 ST1000LM028 ST750LM000 Previous generations of Seagate Self Encrypting Drive models were called Full Disk Encryption FDE models before a differentiation between drive based encryption and other forms of encryption was necessary The Self Encrypting Drive models indicated on the cover of this product manual have provisions for Security of Data at Rest based on the standards defined by the Trusted Computing Group see www trustedcomputinggroup org For more information on FIPS 140 2 Level 2 certification About FIPS on page 16 These drives provide the following key features 5400 RPM spindle speed 64MB buffer 8GB NAND flash Quiet operation Fluid Dynamic Bearing FDB motor High instantaneous burst data transfer rates up to 6Gb s Perpendicular recording technology State of the art cache and on the fly error correction algorithms N
40. t environmental protection requirements worldwide including regulations restricting certain chemical substances 2 13 1 European Union Restriction of Hazardous Substances RoHS Directive The European Union Restriction of Hazardous Substances RoHS Directive restricts the presence of chemical substances including Lead Cadmium Mercury Hexavalent Chromium PBB and PBDE in electronic products effective July 2006 This drive is manufactured with components and materials that comply with the RoHS Directive 2 13 2 China Restriction of Hazardous Substances RoHS Directive P E PRSI fa NF E This product has an Environmental Protection Use Period EPUP of 20 years The following table contains information mandated by China s Marking Requirements for Control of Pollution Caused by Electronic Information Products Standard hy 2 mh AA DEFIA RIP EPU o TRAST RPE SFP oP SRS E AES Bk PAR HEE gt Toxic or Hazardous Substances or Elements a Sh RE Hexavalent Polybrominated Polybrominated T i i Dipheryl Dipheryl Ether Name of Parts A ZIRE Bid RE BHA 2 PBDE E O indicates the hazardous and toxic substance content of the part at the homogenous material level is lower than the threshold defined by the China ROHS MCV Standard ORR FARM MEE EL PSMA MA RF BIROHS MCV EREE SCAT TAE X indicates the hazardous and toxic substance content of the part at the homogenous material level is over the threshold defined
41. t mounting precautions when mounting the drive Allow a minimum clearance of 0 030 in 0 76 mm around the entire perimeter of the drive for cooling m Use only M3 x 0 5 mounting screws Do not overtighten the mounting screws Maximum torque 4 0 in lb 0 4519 N m m Four 4 threads 0 080 in 2 032 mm minimum screw engagement recommended m Avoid excessive drive distortion when mounting Refer to the following specifications for stiffness deflection information Top cover stiffness deflection 10 mm probe 1 02kgf or Operating no performance degradation emitted noise 5 mm probe 0 92kgf mechanical damage or hard errors Non operating no hard errors 20 mm probe 2 0kgf at any point of top cover 20 mm probe 15 0kgf at top cover edges only Figure 3 Mounting Dimensions for standard models 008 3 951 010 0 20 1100 33 25 55 1 0 835 010 21 219 257 0 324 2 010 8 2310 25 2 7501 010 69 95 0 25 3 Breetter hole Do not cover or sool Recommended case tenp messurenent location 2 M x 0 S 6H Mount ing holes Both sides 70 12 min full thread 0 37040 008 19 5 10 2 2x 118 4x MY 0 5 6H Mount i holes Both sides TF 0 10 min full thread 2 430 61 722 qu 0 160 14 064 SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C 15 ABOUT FIPS 4 0 ABOUT FIPS The Federal Information Processing Standard FIPS Publication 140 2 FIPS PUB 1
42. tor Pin Definitions SEGMENT PIN FUNCTION DEFINITION Sl Ground 2nd mate S2 A Differential signal pair A from Phy S3 A S4 Ground 2nd mate S5 B Differential signal pair B from Phy S6 Bt SIGNAL S7 Ground 2nd mate Key and spacing separate signal and power segments Pl V33 3 3V power P2 V33 3 3V power 3 V33 P 3 3V power pre charge 2nd mate P4 Ground lst mate PS Ground 2nd mate P 6 P9 V5 Ground 2nd mate SV power P10 Ground 2nd mate P11 Ground or LED signal If grounded drive does not use deferred spin P 12 P13 Vio 12V power pre charge 2nd mate P14 Vie 12V power 15 Vio P NOTES Ground lst mate 12V power 1 All pins are in a single row with a 1 27 mm 0 050 in pitch 2 The comments on the mating sequence apply to the case of backplane blindmate connector only In this case the mating sequences are the ground pins P4 and P12 the pre charge power pins and the other ground pins SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C 17 the signal pins and the rest of the power pins SERIAL ATA SATA INTERFACE 3 There are three power pins for each voltage One pin from each voltage is used for pre charge when installed in a blind mate backplane configuration 4 All used voltage pins V must be terminated 5 3 SUPPORTED ATA COMMANDS Table 9 lists Serial ATA sta
43. ty 705 Gb in2 avg Spindle speed Sustained data transfer rate OD 5400 RPM 100 MB s max I O data transfer rate 600 MB s max ATA data transfer modes supported PIO modes 0 4 Multiword DMA modes 0 2 Ultra DMA modes 0 6 Cache buffer 64MB 9 5 0 2 mm 0 374 008 in 69 85 0 25 mm 2 750 0 010 in Weight typical 100 35 0 20 0 25 mm 3 951 0 008 0 010 in 115 g 0 254 1b Average latency 5 6 ms Startup current typical 5V peak Voltage tolerance including noise 10A 5V 5 Operating temperature 0 to 60 C Nonoperating temperature Ambient Temperature gradient max Relative humidity 40 to 70 C 20 C per hour max operating 35 C per hour max nonoperating 5 to 95 operating 5 to 95 nonoperating Relative humidity gradient 30 per hour max SEAGATE LAPTOP SSHD SATA PRODUCT MANUAL REV C 4 DRIVE SPECIFICATIONS Table 1 Drive Specifications Summary continued ST1000LM014 ST1000LM015 AND ST1000LM028 173 0LM000 DRIVE SPECIFICATION 37 7 C max operating Wet bulb temperature max 40 02 max aonoperating Altitude operating 304 8 m to 3048 m 1000 ft to 10 000 ft Altitude nonoperating 304 8 m to 12 192 m 1000 ft to 40 000 ft below mean sea level max Operational Shock 350 Gs at 2 ms max Non Operational Shock 1000 Gs at 1 ms max 5 200 Hz 2 0
Download Pdf Manuals
Related Search