Ubiquiti Networks mFi-MSW
Contents
1. mFi Wall Mount Motion Sensor Compliance FCE Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operations of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Industry Canada This Class A digital apparatus complies with Canadian ICES 003 To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that permitted for successful communication2. Compliance This device complies with Industry Canada licence exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Cet appareil num rique de la classe A est confrome a la norme NMB 003 Canada Pour r duire le risque d interf rence aux autres utilisateurs le type d antenne et son gain doivent tre choisies de facon que la puissance isotrope rayonn e quivalente PIRE ne d passe pas ce qui est n cessaire pour une communication r ussie Cet appareil est conforme a la norme RSS Industrie Canada exempts de licence norme s Son fonctionnement est soumis aux deux conditions suivantes 1 cet appareil ne peut pas provoquer d interf rences et 2 cet appareil doit accepter toute interf rence y compris les interf rences qui peuvent causer un mauvais fonctionnement du dispositif RF Exposure Warning The transceiver described here emits radio frequency energy Although the power level is low the concentrated energy from a directional antenna may pose a health hazard Do not allow people to come closer than 20 cm to the antenna when the transmitter is operating Additional information on RF exposure is available on the Internet at www fcc gov oet info documents bulletins 15 mFi Wall Mount Motion Sensor L metteur r
3. waste disposal service or the shop where you purchased the product Espanol La Directiva 2002 96 CE de la UE exige que los equipos que lleven este simbolo en el propio aparato y o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados El simbolo indica que el producto en cuestion debe separarse de los residuos dom sticos convencionales con vistas a su eliminaci n Es responsabilidad suya desechar este y cualesquiera otros aparatos el ctricos y electr nicos a trav s de los puntos de recogida que ponen a su disposici n el gobierno y las autoridades locales Al desechar y reciclar correctamente estos aparatos estar contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas Si desea obtener informaci n m s detallada sobre la eliminaci n segura de su aparato usado consulte a las autoridades locales al servicio de recogida y eliminaci n de residuos de su zona o pregunte en la tienda donde adquiri el producto 17 mFi Wall Mount Motion Sensor Frangais La directive europ enne 2002 96 CE exige que l quipement sur lequel est appos ce symbole sur le produit et ou son emballage ne soit pas jet avec les autres ordures m nageres Ce symbole indique que le produit doit tre limin dans un circuit distinct de celui pour les d chets des m nages Il est de votre responsabilit de jeter ce mat riel ainsi que tout autre mat riel lectr
4. open the casing to adjust the jumpers The SENS and LED jumpers are the only ones that you may want to change The SENS jumper can be changed to reduce the sensitivity of the microwave sensor The LED jumper can be turned on so the LED is visible when the motion sensor is triggered The LED jumper can be turned on permanently or temporarily for walk testing testing the positioning of the sensor The following jumper settings are available Selection NO NC Normally Open Normally Closed This controls whether the alarm signal is normally on or off NC is the default setting and should not be changed SENS Sensitivity Set to Sensitive by default this controls the Microwave Sensor sensitivity Sensitive Standard Sensitivity is reduced when set to Standard PIR Passive Infrared Sensor Enabled by default Removing the jumper will disable Enabled Disabled this sensor MW Microwave Sensor Enabled by default Enabled Disabled Removing the jumper will disable this sensor AM Anti Mask In the default disabled mode an alarm is triggered if both the PIR and MW sensors are simultaneously triggered When enabled an alarm will be triggered if the PIR sensor is physically blocked and the MW sensor detects an object four times continuously Enabled Disabled LED LEDs are off by default ON OFF LED If you need to access the jumper settings use a Phillips screwdriver to remove the screw at the base of the sensor Lift t
5. UBT finn NETWORKS mFi Wall Mount Motion Sensor Model mFi MSW Quick START GUIDE Introduction Introduction Thank you for purchasing the Ubiquiti mFi Wall Mount Motion Sensor This sensor is designed for use with the mFi mPort Once they are connected you can use the mFi Controller software to monitor your sensors using your Web browser Package Contents ze S 2 O S at Wall Mount Mounting Mounting Jumpers Motion Sensor Bracket Base Qty 3 Quick Start M3x20 mm M2 6x8 mm Anchors Guide Screws Qty 2 Screws Qty 2 Qty 2 System Requirements mFi mPort CAT5 6 Cable Drill with 6 mm Drill Bit Optional for Wall Mount Phillips Screwdriver mFi Wall Mount Motion Sensor Hardware Overview Front HR La Motion Sensor Back de mFi RJ45 Port Hardware Installation Hardware Installation Installation Tips Avoid installing the sensor in areas where it will face direct or reflected sunlight Ensure there are no obstructions in the field of view Avoid placing the sensor in areas where the environmental temperature may change rapidly Locate the sensor at least 1 meter away from the nearest fluorescent light to avoid interference Ceiling Mount 1 _ Use a Phillips screwdriver to secure the Mounting Bracket to the ceiling with the two M3x20 mm Screws Proceed to Connecting the Cabling and Mounting Base on page 6 mFi Wall Mount Mo
6. cepteur d crit ici met de l nergie de fr quence radio Bien que le niveau de puissance est faible l nergie concentr e partir d une antenne directionnelle peut pr senter un danger pour la sant Ne pas permettre aux gens de se rapprocher de 20 cm l antenne lorsque l metteur est en marche Des renseignements suppl mentaires sur l exposition aux RF est disponible sur Internet www fcc gov oet info documents bulletins CE Marking CE marking on this product represents the product is in compliance with all directives that are applicable to it Alert Sign Follows CE Marking Alert sign must be indicated if a restriction on use applied to the product and it must follow the CE marking CEO Compliance RoHS WEEE Compliance Statement English European Directive 2002 96 EC requires that the equipment bearing this symbol on the product and or its packaging must not be disposed of with unsorted municipal waste The symbol indicates that this product should be disposed of separately from regular household waste streams It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities Correct disposal and recycling will help prevent potential negative consequences to the environment and human health For more detailed information about the disposal of your old equipment please contact your local authorities
7. evanta best mmelser som framg r av direktiv 1999 5 EG Por medio de la presente UBIOUITI NETWORKS declara gue el UBIOUITI NETWORKS device cumple con los reguisitos esenciales y cualesguiera otras disposiciones aplicables o exigibles de la Directiva 1999 5 CE Niniejszym firma UBIOUITI NETWORKS o wiadcza e produkt serii UBIOUITI NETWORKS device spetnia zasadnicze wymagania i inne istotne postanowienia Dyrektywy 1999 5 EC UBIOUITI NETWORKS declara gue este UBIOUITI NETWORKS device est conforme com os reguisitos essenciais e outras disposi es da Directiva 1999 5 CE Prin prezenta UBIOUITI NETWORKS declar c acest dispozitiv UBIOUITI NETWORKS este n conformitate cu cerintele esentiale si alte prevederi relevante ale Directivei 1999 5 CE RR042412 Email support ubnt com Phone 9 a m 5 p m PST 408 942 1153 ef Wiki Page wiki ubnt com Support Forum forum ubnt com Downloads downloads ubnt com UBIQUITI NETWORKS www ubnt com 2012 Ubiquiti Networks Inc All rights reserved
8. he case up and the jumpers will be accessible vas LED The LED is disabled by default and can only be enabled by opening the product case and adjusting the jumper When the LED is enabled the bottom panel with the sensor will illuminate in one of the following colors when motion is detected Color Detection Indicates that the microwave sensor detected motion E UR Indicates that an alarm was triggered because the infrared sensor and microwave sensor both detected H motion mFi Wall Mount Motion Sensor Detection Pattern 110 10x 10 mat 25 C Top View Side View 2 3m 0 5m 25m 8m 10m Specifications Specifications mFi MSW Dimensions 146 x 66 x 52 mm Weight 127g Power Supply 9 16VDC 12VDC Typical Current Drain 35mA 12VDC Infrared Sensor Dual Element Microwave Sensor DRO Patch Antenna Alarm Period 3 Seconds Alarm Output NC NO 24VDC 0 2A Max Detection Range 10x 10m 110 25 C Mounting Wall Ceiling Kits included Mounting Height 2 3 m Typical Detection Speed 0 3 to 3 0 m sec RFI Immunity Operating Temperature Avg 10 V m 80 to 2 000 MHz 10 to 45 C Humidity 95 RH Max Ports 1 mFi RJ45 Port 11 mFi Wall Mount Motion Sensor General Warranty UBIQUITI NETWORKS Inc UBIOUITI NETWORKS represents and warrants that the Products fu
9. ian fslenska Icelandic Italiano Italian Hereby UBIQUITI NETWORKS declares that this UBIQUITI NETWORKS device is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC K esolevaga kinnitab UBIQUITI NETWORKS seadme UBIQUITI NETWORKS device vastavust direktiivi 1999 5 EU p hin uetele ja nimetatud direktiivist tulenevatele teistele asjakohastele s tetele UBIQUITI NETWORKS vakuuttaa t ten ett UBIQUITI NETWORKS device tyyppinen laite on direktiivin 1999 5 EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen Par la pr sente UBIQUITI NETWORKS d clare que l appareil UBIOUITI NETWORKS device est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999 5 CE Hiermit erkl rt UBIQUITI NETWORKS dass sich diese UBIQUITI NETWORKS device in Ubereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999 5 EG befindet BMWi ME THN NAPOYSA UBIOUITI NETWORKS AHAONEI OTI UBIQUITI NETWORKS device YMMOPOONETAI MPOZ TIZ OYZIQAEIZ ANAITHZEIZ KAI TIZ AOINES 2XETIKEZ AIATAZEIZ THE OAHTIAz 1995 5 EK Alulirott UBIQUITI NETWORKS nyilatkozom hogy a UBIQUITI NETWORKS device megfelel a vonatkoz alapvet k vetelm nyeknek s az 1999 5 EC ir nyelv egy b el r sainak H r me I sir UBIQUITI NETWORKS yfir vi a UBIQUITI NETWORKS device er i samr mi vi gr
10. ique ou lectronique par les moyens de collecte indiqu s par le gouvernement et les pouvoirs publics des collectivit s territoriales Lelimination et le recyclage en bonne et due forme ont pour but de lutter contre l impact n faste potentiel de ce type de produits sur l environnement et la sant publique Pour plus d informations sur le mode d limination de votre ancien quipement veuillez prendre contact avec les pouvoirs publics locaux le service de traitement des d chets ou l endroit ou vous avez achet le produit Declaration of Conformity Cesky UBIQUITI NETWORKS timto prohla uje e tento Czech UBIQUITI NETWORKS device je ve shod se zakladnimi po adavky a dal imi p slu n mi ustanoven mi sm rnice 1999 5 ES Dansk Undertegnede UBIQUITI NETWORKS erkl rer herved Danish at folgende udstyr UBIOUITI NETWORKS device overholder de v sentlige krav og vrige relevante krav i direktiv 1999 5 EF Nederlands Hierbij verklaart UBIQUITI NETWORKS dat het toestel Dutch UBIQUITI NETWORKS device in overeenstemming is met de essenti le eisen en de andere relevante bepalingen van richtlijn 1999 5 EG Bij deze verklaart UBIQUITI NETWORKS dat deze UBIQUITI NETWORKS device voldoet aan de essenti le eisen en aan de overige relevante bepalingen van Richtlijn 1999 5 EC Declaration of Conformity English Eesti Estonian Suomi Finnish Francais French Deutsch German EN UK Greek Magyar Hungar
11. placement necessitated by catastrophe fault negligence misuse abuse or accident by Buyer Buyer s customers or any other parties The warranty period of any repaired or replaced product shall not extend beyond its original term General Warranty Warranty Conditions The foregoing warranty shall apply only if I The Product has not been subjected to misuse neglect or unusual physical electrical or electromagnetic stress or some other type of accident ll No modification alteration or addition has been made to the Product by persons other than UBIOUITI NETWORKS or UBIOUITI NETWORK S authorized representatives or otherwise approved by UBIOUITI NETWORKS lll The Product has been properly installed and used at all times in accordance and in all material respects with the applicable Product documentation IV All Ethernet cabling runs use CAT5 or above shielded cabling Disclaimer UBIOUITI NETWORKS does not warrant that the operation of the products is error free or that operation will be uninterrupted In no event shall UBIOUITI NETWORKS be responsible for damages or claims of any nature or description relating to system performance including coverage buyer s selection of products for buyer s application and or failure of products to meet government or regulatory reguirements Returns In the unlikely event a defect occurs please work through the dealer or distributor from which this product was purchased
12. rnished hereunder shall be free from defects in material and workmanship for a period of one 1 year from the date of shipment by UBIQUITI NETWORKS under normal use and operation UBIQUITI NETWORKS sole and exclusive obligation under the foregoing warranty shall be to repair or replace at its option any defective Product that fails during the warranty period The expense of removal and reinstallation of any item is not included in this warranty The foregoing warranty is exclusive and in lieu of all other warranties express or implied including the implied warranties of merchantability and fitness for a particular purpose and any warranties arising from a course of dealing usage or trade practice with respect to the products Repair or replacement in the manner provided herein shall be the sole and exclusive remedy of Buyer for breach of warranty and shall constitute fulfillment of all liabilities of UBIQUITI NETWORKS with respect to the quality and performance of the Products UBIQUITI NETWORKS reserves the right to inspect all defective Products which must be returned by Buyer to UBIQUITI NETWORKS factory freight prepaid No Products will be accepted for replacement or repair without obtaining a Return Materials Authorization RMA number from UBIQUITI NETWORKS Products returned without an RMA number will not be processed and will be returned to Buyer freight collect UBIQUITI NETWORKS shall have no obligation to make repairs or re
13. tion Sensor Wall Mount 1 Use a 6 mm drill bit to drill two holes 20 mm apart with one directly above the other 20 mm en 2 Insert the anchors into the holes A 3 Use a Phillips screwdriver to secure a M3x20 Screw to the top anchor in the wall Ensure to leave a clearance of approximately 1 mm between the screw head and the anchor 1mm Hardware Installation 4 Align the top hole of the Mounting Bracket over the screw and slide the Mounting Bracket down E 5 Use the Phillips screwdriver to secure the second M3x20 Screw through the bottom of the Mounting Bracket into the anchor mFi Wall Mount Motion Sensor Connecting the Cabling and Mounting Base 1 Connect a straight through CAT5 6 cable to the mFi RJ45 port on the mFi MSW e J ms S x 2 Secure the mFi MSW to the Mounting Base using the two M2 6x8 mm Screws Hardware Installation 3 Connect the Mounting Base to the Mounting Bracket 4 Connect the other end of the CAT5 6 cable from the sensor to an mFi RJ45 port on the mFi mPort Refer to the User Guide on the CD ROM that was included with your mFi mPort for instructions on configuring the mFi MSW in the mFi Controller software The User Guide can also be downloaded from our website at www ubnt com mfi mFi Wall Mount Motion Sensor Jumper Settings The mFi MSW has jumpers located inside the product casing Typically there is no need to
14. unnkr fur og a rar kr fur sem ger ar eru tilskipun 1999 5 EC Con la presente UBIOUITI NETWORKS dichiara che guesto UBIOUITI NETWORKS device conforme ai reguisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999 5 CE 19 mFi Wall Mount Motion Sensor Latviski Latvian Lietuviskai Lithuanian Malti Maltese Norsk Norwegian Slovensky Slovak Svenska Swedish Espanol Spanish Polski Polish Portugu s Portuguese Romana Romanian 20 Ar o UBIQUITI NETWORKS deklar ka UBIQUITI NETWORKS device atbilst Direkt vas 1999 5 EK b tiskaj m pras b m un citiem ar to saist tajiem noteikumiem UBIQUITI NETWORKS deklaruoja kad Sis UBIQUITI NETWORKS jrenginys atitinka esminius reikalavimus ir kitas 1999 5 EB Direktyvos nuostatas Hawnhekk UBIQUITI NETWORKS jiddikjara li dan UBIQUITI NETWORKS device jikkonforma mal ti ijiet essenzjali u ma provvedimenti o rajn relevanti li hemm fid Dirrettiva 1999 5 EC UBIQUITI NETWORKS erkl rer herved at utstyret UBIQUITI NETWORKS device er i samsvar med de grunnleggende krav og vrige relevante krav i direktiv 1999 5 EF UBIQUITI NETWORKS t mto vyhlasuje e UBIQUITI NETWORKS device sp a z kladn po iadavky a v etky pr slu n ustanovenia Smernice 1999 5 ES H rmed intygar UBIQUITI NETWORKS att denna UBIOUITI NETWORKS device st r verensst mmelse med de v sentliga egenskapskrav och vriga rel
Download Pdf Manuals
Related Search