Valcom Station Port
Contents
1. WOW il P lutions is So ISSUE 3 VIP 810 NETWORKED STATION PORT INTRODUCTION The VIP 810 networked station port allows most loop start terminal devices to be connected to a managed IP based Local area network LAN or Wide area network WAN SPECIFICATIONS Access Methods e PBX FXO Port e POTS telephone set Features RJ 45 for network connection RJ 11 telephone connection Front panel activity LED Network activity LEDs on RJ 45 4 RENS 2 5mm jack for DC power 115VAC TO 24VDC adapter provided Dimensions Weight e 1 88 H x 5 50 W x 4 15 D 4 78cm H x 13 97cm W x 10 54cm D e Weight 0 55 Ibs 0 25 kg Nominal Specifications Input Impedance 600 Ohms Input Level 10dBm Output Impedance 600 Ohms Output Level 10dBm nominal Nominal Power Requirements Voltage 24VDC Current 325mA Environment Temperature 0 to 40 C Humidity 0 to 85 non precipitating INSTALLATION NOTE The telephone system referred to in this manual is the customer premise equipment such as an electronic key system a PBX or a dedicated single line telephone sets The VIP 810 is not intended for direct or indirect connection to the public telephone network When used with a customer premise telephone system such as a key system or PBX system these units are interfaced to the system via a fully protected loop start trunk FXO port Also the host system must be configured to disallow central office trunk conferenc2. data network to extend the station port to a remote Door Phone This could be installed where network access is available but not telephone wiring When initiating a call from the VIP 820 an open loop disconnect signal is required from the PBX Station Port EL rae Pee Me N e eC ELIS VALEOM _ OOo ee 66s VIP 810 VIP 820 AN PBX k WAN In this example the VIP 810 and VIP 820 are connected to the data network to extend the station port to a telephone at a remote location This could be installed where network access is available but telephone wiring is not When initiating a call from the VIP 820 an open loop disconnect signal is required from the PBX Station Port ATION PURI ER en a VIP S810 VIP 800 te LAN R WAN 947052 TECHNICAL ASSISTANCE When trouble is reported verify power is being supplied to the unit and there are no broken connections Check voltages for proper polarity to the one way amplified speakers Table 1 identifies symptoms of some possible problem
3. line key electronic key system or dial trunk access code PBX to connect to the VIP 810 The VIP 810 automatically disconnects from page when you hang up Pots Telephone Access The VIP 810 may be connected to a POTS telephone set This gives you direct access to the network Use the VIP 810 with a PBX Loop Start Trunk Port and a VIP 800 to interface the telephone system to Valcom powered speakers over a network When the PBX Loop Start Trunk Port is accessed the VIP 810 will activate the VIP 800 LUUP START TRUNK PORT a aly ar die aM NI WORI VIP 810 ee LAN PBX UR KE Y SYSTEM j i Sad In this example the VIP 810 is connected to the data network jack already installed and now the network connected telephone can reach into the existing Valcom Page Control to access one way all call priority paging This configuration could be used at a guard shack where network access is available but telephone access is not 947052 In this example the VIP 810 and VIP 800 are connected to the data network as a stand alone paging system This could be installed where network access is available but telephone access is not Ver 610 VIP 800 AN Soe ee m WAN In this example the VIP 810 and VIP 820 are connected to the
4. f one year from the date of shipment The obligation under this warranty shall be limited to the replacement repair or refund of any such defective device within the warranty period provided that 1 inspection by Valcom Inc indicates the validity of the claim 2 the defect is not the result of damage misuse or negligence after the original shipment 3 the product has not been altered in any way or repaired by others and that factory sealed units are unopened a service charge plus parts and labor will be applied to units defaced or physically damaged 4 freight charges for the return of products to Valcom are prepaid 5 all units out of warranty are subject to a service charge The service charge will cover minor repairs major repairs will be subject to additional charges for parts and labor This warranty is in lieu of and excludes all other warranties expressed or implied and in no event shall Valcom Inc be liable for any anticipated profits consequential damages loss of time or other losses incurred by the buyer in connection with the purchase operation or use of the product This warranty specifically excludes damage incurred in shipment In the event a product is received in damaged condition the carrier should be notified immediately Claims for such damage should be filed with the carrier involved in accordance with the F O B point 947052
5. ing in order to prevent indirect connection to the public network Precautionary Designations CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION To reduce the risk of electric shock Do not remove cover No user serviceable parts inside Refer servicing to qualified service personnel This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit 947052 Mounting The VIP 810 was designed for wall or table mounting Secure unit to wall studs or a suitable brace away from heat sources or strong magnetic fields motors fans power supplies etc with the control and terminal strip accessible One wood screw is included for mounting Power Connections NOTE This equipment must be installed near an AC power outlet due to the power cord being used as a disconnect device e The VIP 810 is provided with a VP 324 for North American use After all required connections have been made plug the VP 324 into appropriate AC wall outlet APPLICATION EXAMPLES PBX Access When using the VIP 810 with an electronic key system or PBX a VIP 810 must be connected to a loop start trunk FXO port When using the VIP 810 with a PBX station port a VIP 820 must be used to interface the telephone system with the network Operation Press
6. s with solutions If a spare unit is available substitute a spare unit for the suspected defective unit Assistance in troubleshooting is available from the factory Call 540 563 2000 and press 1 for Technical Support or via email at support valcom com When requesting assistance you should include all available information It is strongly suggested that you go to the web site and follow the trouble resolution procedure at http voip valcom com Valcom equipment is not field repairable Valcom Inc maintains service facilities in Roanoke VA Should repairs be necessary attach a tag to the unit clearly stating your company name address phone number contact person and the nature of the problem Send the unit to Valcom Inc Repair amp Return Dept 5614 Hollins Road Roanoke Va 24019 5056 TABLE 1 TROUBLESHOOTING CHART SYMPTOM PROBABLE CAUSE AND SOLUTION 1 No output to speakers Check for the presence of audio on the page outputs of the VIP 810 during a page using a test set Refer to installation section for connection information Check the DC voltage at the output of the VP 324 It should be 20 to 28VDC 2 No music output Using a test set check for music on the music input terminals Check that speakers are connected to page outputs VALCOM LIMITED WARRANTY Valcom Inc warrants its products to be free from defects in materials and workmanship under conditions of normal use and service for a period o
Download Pdf Manuals
Related Search