Pyle PDWM2700 microphone
Contents
1. TROUBLE SHOOTING Please read and check the following points before asking for service The wireless microphone fails fo work Check the microphone battery by switching the microphone ON If power LED indicator lights red replace the battery Check the POWER indicator on the receiver unit is ON If not check the mains power adapter is firmly plugged into a worki mains socket Check the amplifier system is ON and the microphone controls set correctly Check the radio microphone jack lead is firmly connected into the output socket on the rear panel of the receiver unit and into the MIC input socket on your amplifier The working range is limited Check the microphone battery condition see above Check the aerials are fully extended Adjust the position of the aerials to achieve the best reception Check the settings of the microphone controls on the amplifier Adjust volume and tone to get the beat sound without any trace of feedback www pyleaudio com ng gt PYLE PDWM2700 PRO TWO CHANNELS VHF WIRELESS MICROPHONE PYLE SPRO OPEN D PPE oreson VHF WIRELESS MICROPHONE PDWM2700 SIGNAL A AUDIO POWER SIGNALA AUDIO USER S MANUAL ank you for choosing our VHF wireless microphone system We strongly suggest that you carefully study the2. RY COVER gt BALANCED AF OUT PYLE PRO CLOSE lt OPEN C OPEN J 9V BATTERY Lavalier MIC Optional 1 Switch on the wireless microphone receiver unit by pressing the POWER switch and the POWER light will illuminate to show the receiver unit is working 2 Fully extend the aerials to the maximum height 3 Switch ON the transmitter Power LED indicator will flash once the go off When the microphone is ON the receiver RF 1 Slide up the battery cover in the front of the body pack as per above sketch map Install the provided 9 volt battery and the battery cover Make sure to connect with the correct polarity 2 Move power switch to ON position Power LED indicator will flash once and then go off This indicates correct operation indicator will light If power LED indicator lights red this indicates the battery is low Please replace with new battery 4 Adjust the volume and tone levels of your amplifier system as well as the receiver amp the body pack as required 3 Move power switch to centre to mute the microphone 5 When the transmitter is not going to be used for along period of time please take out the battery from transmitter 4 Adjust the volume control to you get the sufficient sound from your speaker Note that switching the microphone on and off can cause interference that will be heard if the microphone volume level of the 5 If the microphone is not going to be u
3. e immediately 9 Only replace the battery with the same or an equivalent type 11 Do not use any solvents to clean any part of the radio microphone system Oe ee 10 Only replace the battery with the same or an environmentally friendly manner in accordance with the relevant legislation SPECIFICATIONS A Overall system 1 Oscillation mode 2 Carrier Frequency Range 3 Frequency Stability 4 Max Deviation 5 Dynamic Range 6 S N Ration 7 T H D 8 Frequency Response 9 Operating Range C Transmitter 1 Mike capsule 2 Antenna 3 RF Output 4 Spurious 5 Power Supply B Receiver Quartz controlled 1 Sensitivity VHF 160 270MHz 2 lmage Rejection 0 005 3 Stability 56KHz with level limiting 4 Audio output gt 110dB gt 100dB 5 Power supply lt 0 5dB 100Hz 15KHz 50M Handheld dynamic Headset or lavalier MIC condenser Built in housing Handheld MIC external Belt pack lt 10mW lt 40dBC 9V battery 226 6dBIV at SIN gt 70dB gt 60dB gt 80dB 12db 6000hm unbalanced and balanced 12V 500mA AMPLIFIER 2 BALANCED AF OUT RADIO MIC RECEIVER UNIT SPEAKERS MAINS POWER To connect the wireless microphone to your amplifier system Refer to above installation diagram amplifier Plug one end of the mains power adapter into a suitabl
4. e mains socket Plug the other end of the adapter into receiver DC 12V input socket 5 ADAPTER Using the supplied 6 35mm to 6 35mm lead connect from the AF OUT jack of the receiver to the MIC INPUT socket on your HANDHELD MICROPHONE UNSCREW BATTERY COVER TO INSERT BATTERY NGS iy Y OO KORNO AOAO AOON YAM LSS A RAOIN OONN RY Rr OUR l OOY ne Wi Xi XXX NOON KNS KNSS OMEN a NSIS OW BATTERY CONDITION POWER SWITCH POWER COVER INDICATOR 1 Unscrew the battery cover at the end of the microphone Install the provided 9 volt battery and then close the cover Make sure to connect with the correct polarity 2 Move power switch to ON position Power LED indicator will flash once and then go off This indicates correct operation If power LED indicator lights red this indicates the battery is low Please replace with new battery 3 Move power switch to center to mute the microphone 4 If the microphone is not going to be used for a long period of time please take out the battery to prevent damage by battery leakage BODYPACK TRANSMITTER VOLUME CONTROL HIGH LOW ON OFF LED MIC IN o gt SDPYLE enorsesioun _ VHE WIRELESS MICROPHONE PDWM2700 SIGNAL A AUDIO POWER SI GNAL A AUDIO BATTE
5. se instructions before attempting to operate the system CONTENTS 1 Precautions 2 Handheld microphone 3 Body pack transmitter 4 Receiver 5 Instalation 6 Specifications 7 Troubleshooting PRECAUTIONS 1 Avoid exposure of the system to rain or moisture 2 No user serviceable parts inside the system Refer all servicing to a qualified technician only 3 Handle the microphone carefully dropping or other shocks may cause failure 4 Aoid using the system where it may be subjected to heat such as in direct sunlight near radiators or other heat sources 5 Should any liquid be spilt on the system stop using it immediately It may be possible to dry the system but you should have it checked by a qualified technician before using it again 6 Take care with the mains power adapter and lead If damaged in any way do not use the with the system and refer to a qua lified for repair 7 Only use the system with the supplied components do not attempt to use with any other mains power supply adapter or microphone 8 If the microphone is not going to be used for a time remove the battery to prevent leakage In the event of electrolyte leakage inside the battery compartment carefully remove using a damp cloth Take care not to get battery electrolyte in contact with your skin however if it does wash your hands under a running tap If electrolyte comes into contact with your eyes seek medical advic
6. sed for a long period of time please take out the battery to prevent damage by battery amplifier systemiis stili set High leakage aR AA 4
Download Pdf Manuals
Related Search