Samsung NC240
Contents
1. d i z i I e When using the DVI OUT port e Connect between the DVI OUT port on the product and the DVI port on your monitor using a DVI cable DVI OUT Connect to the DVI OUT RGB OUT port to display the same picture on another monitor such as the projector For presentation purposes Installing the Product 1 7 Connecting with a PC Connect the RGB IN port of the product to the D Sub port of your PC with a D Sub cable Use the RGB IN port to directly connect the monitor to a PC 1 7 Installing the Product 1 8 Connecting a Stereo Cable Connect the AUDIO IN port on the rear side of the monitor to the sound card of the PC AUDIO IN Installing the Product 1 9 Connecting USB The USB port of the monitor supports High Speed Certified USB 1 1 Connect USB devices such as a mouse keyboard and external storage devices DSC Digital Still Camera MP3 external storage etc F You can use a USB device such as a mouse keyboard Memory Stick or external hard disk drive by connecting them to the D zu USB port of the monitor without connecting them to the PC 1 9 Installing the Product 1 10 Connecting Headphones Connect your headphones to the Headphone connection terminal You may connect your headphones to the monitor Installing the Product 1 11 Connecting MIC Connect the microphone cable to the MIC port on the monitor You m2. function is set to Off The color is weird The picture is displayed in black and white Is the entire screen displayed in the same color as if viewing the screen through a cellophane paper Check the cable connection to the computer Reinsert the graphics card into the computer completely Check if the lt Color Effect gt is set to lt Off gt Is the graphics card configured correctly Set up the graphics card referring to the user manual Troubleshooting 2 1 The display area suddenly moves to an edge or to the center Did you change the graphics card or the driver Please press the AUTO button to run the auto adjustment function Did you change the resolution and frequency appropriate to the product Set the resolution and the frequency to the appropriate values in the graphics card Refer to the Standard Signal Mode Table Is the graphics card configured correctly Set up the graphics card referring to the user manual The pictures are out of focus Did you change the resolution and the frequency appropriate to the product Set the resolution and the frequency to the appropriate values in the graphics card Refer to the Standard Signal Mode Table The color is displayed in 16 bit 16 colors The color has been changed after changing the graphics card Did you install the device driver for the product Windows ME XP 2000 Set the color again by sele
3. SyncMaster NC190 NC240 a LCD MONITOR quick start guide 1 Installing the Product 1 1 Package Contents e Unpack the product and check if all of the following contents have been included e Store the packaging box in case you need to move the Product at a later stage Monitor CONTENTS Installation Manual Product Warranty User Manual Power Cord SS X Keyboard USB Mouse USB D Sub Cable OPTIONAL PARTS 1 2 Installing the Stand Before assembling the product place the product down on a flat and stable surface so that the screen is facing downwards Place a soft cloth over the table to protect the product and place the product onto the cloth so that the front of the product is facing downwards Do not remove the stopper pin before installing the base Hold the main body of the product with your hand as shown by the figure Insert the stand base into the stand connection part in the direction shown in the figure Turn the connecting screw at the bottom of the stand fully so that it is completely fixed After the installation of the base stand the monitor up as shown in the figure Now you can remove the stopper pin to adjust the stand Caution Avoid lifting the product holding only the stand Disassembly is in the reverse order of assembly 1 3 Installing a Wall Mount Before installation disassemble the product according to the fo
4. ay connect your microphone to the monitor 1 11 Installing the Product 1 12 Kensington Lock A Kensington Lock is an anti theft device that enables users to lock the product so that they can safely use it in public locations Since the shape and usage of the locking device may differ depending on the model and the manufacturer for more information refer to the User Manual supplied with the locking device You have to purchase an additional locking device Locking the product 1 Insert the locking part of the locking device into the hole of the Kensington lock of the product and turn it in the locking direction 2 Connect the Kensington lock cable 3 Tie the Kensington lock cable to a desk or heavy object You can purchase the locking device from an electronics store or an online shop 1 13 Product Operating Buttons Product Operating Buttons MENU ID I F A iD SOURCE AUTO The buttons are located on the bottom of the product Installing the Product 1 12 Icon Description MENU D Press this button to view the On Screen Display OSD This button is also used to exit the OSD or to return to a higher level OSD menu OSD Adjustment Lock This function locks the OSD in order to maintain the current settings or to prevent the settings from being changed by another person On If you press and hold the MENU button down for 5 seconds the OSD Adjustment Lock function is activated O
5. cting Con trol Panel Display Settings Is the graphics card configured correctly Configure the color again in accordance with the new graph ics card driver When I connect the monitor the Unknown monitor Plug amp Play VESA DDC monitor found message is displayed Did you install the device driver for the product Install the device driver referring to the descriptions about the driver installation Check if all the Plug amp Play VESA DDC functions are sup ported referring to the User Manual of the graphics card Install the device driver referring to the descriptions about the driver installation A beep beep sound is heard when booting the computer If the beep sound is generated 3 or more times when booting up the computer please request service for the computer Problems related to Audio No sound Ensure that the audio cable is firmly connected to both the audio in port on your monitor and the audio out port on your sound card Check the volume level Sound level is too low Check the volume level If the volume is still too low after turning the control to its max imum check the volume control on the computer sound card or software program 2 2 Troubleshooting 2 3 FAQ FAQ Please try the following How can change the frequency of the video signal You have to change the frequency of the graphics card For more informat
6. erly the lt Check Signal Cable gt message appears In this case if a blank screen is displayed again make sure that there is no problem with the PC and the connection The product is working properly 2 2 Before Requesting Service Please check the following before requesting After Sales service If the problem continues please contact your nearest Samsung Electronics Service Center A blank screen appears cannot turn the product on Is the power cord connected properly Check the connection status of the power cord Is the lt Check Signal Cable gt message displayed on the screen Check the cable connecting the PC and the product If the message appears on the screen even if the cable is properly connected recheck the input signal by pressing the SOURCE button of the product Is the lt Not Optimum Mode gt message displayed on the screen This occurs when the signal from the graphics card exceeds the maximum resolution or the maximum frequency of the product In this case set up the appropriate resolution and the fre quency for the product Is a blank screen displayed and does the power LED blink at a 1 second interval This occurs when the power saving function is running If you click the mouse or press any key the screen will be turned on The on screen adjustment menu OSD does not appear Did you cancel the screen adjustment Check if the lt OSD Adjustment Lock gt
7. ff If you press and hold the MENU button down for 5 seconds again the OSD Adjustment Lock function is disabled Even if the OSD Adjustment Lock is on lt Brightness gt lt Contrast gt and lt MagicBright gt can be modified This button performs the role of the Power button for the server PC in Client mode and per forms the role of the direction buttons in Analog mode cf When OSD is not on the screen push the button to adjust volume A V Adjust items in the menu SOURCE Use this button to select a function Press SOURCE to select the video signal from a connected device while the OSD is off When the I SOURCE button is pressed to change the input mode a message appears in the upper left of the screen displaying the current mode AUTO In lt Analog gt mode this button is used for auto adjustments In lt Client gt mode it is used to disconnect from the server 5 Press this button to turn the product on or off Installing the Product 2 Troubleshooting Monitor Self Diagnosis You can check if the product is working properly using the Self Diagnosis function e Ifa blank screen is displayed and the Power LED blinks even if the product and the PC are properly connected perform the self diagnosis function according to the procedures below gt Turn the product and the PC off Separate the signal cable from the product m 3 Turn the product on 4 Ifthe product is working prop
8. ion refer to the User Manual of the com puter or the graphics card How can change the resolution How can use the power saving function Windows XP Change the resolution by selecting Control Panel Appearance and Themes Display Settings Windows ME 2000 Change the resolution by selecting Con trol Panel Display Settings For more information refer to the User Manual of the com puter or the graphics card Windows XP Configure it by selecting Control Panel Appearance and Themes Display Screen Saver Set ting or configure it in the BIOS Setup of the computer Windows ME 2000 Configure it by selecting Control Panel Display Screen Saver Setting or Configure it in the BIOS Setup of the computer For more information refer to the Windows user manual for the computer Troubleshooting 2 3 2 3 Troubleshooting
9. llowing steps Installing the Product Lift up the monitor stand to the maximum angle with your left hand and remove the back decoration cover with your right hand as shown in the figure Remove the two screws A Remove the stand arm in the direction shown in the figure This product provides a wall mount of 100 mm x 100 mm 200 mm x 100 mm that complies with the VESA specifications 100 mm x 100 mm 200 mm x 100 mm A Wall Mount Base B Wall Mount Kit Optional Turn the product off and unplug the power cord from the wall outlet Place a soft cloth or cushion on a flat surface to protect the panel and place the product face down Separate the stand gt oe SS Align the groove of the Monitor s wall mount base with the groove in the wall mount ki and firmly fix the wall mount kit by fastening the screws 1 3 Installing the Product gp you use a screw that is longer than the standard specifications the inside of the product may be damaged For wall mounts that are not compatible with the standard VESA specifications the length of the screw may differ depending on the corresponding specifications Do not use screws that are incompatible with the standard VESA specifications and do not assemble them using excessive force This may result in damage to the product or injury due to the product falling Samsung shall not be held liable for any damage or injury Samsung shall not be held liable for any damage to the
10. product or injury caused by using a stand that is not compatible with the specified specifications or due to an installation not performed by an authorized installation engineer eWhen installing the product using a wall mount purchase a wall mount that provides at least 4 inches 10 cm of space from the wall Samsung shall not be held liable for any problems caused by using a stand that is not compatible with the specified specifications eUse a wall mount according to specifications of your country 1 4 Connecting to your Network The connecting part may differ depending on the product model Connect between the LAN port on the product and your network using a LAN cable The two LAN ports are designed to work as an Internet HUB One port can be used for input and the other port for output to connect the product to an external Internet device Both ports can be used for either input or output Installing the Product 1 4 1 5 Connecting Power Connect one end of the power cord to the POWER port of the product and connect the other end of the power cord to a 220V or 110V wall outlet The input voltage is switched automatically 1 5 Installing the Product 1 6 Connecting to another Monitor Please select the right connection method for your monitor e When using the RGB OUT port e Connect between the RGB OUT port on the product and the D Sub port on your monitor using a D Sub cable Te ii wu z
Download Pdf Manuals
Related Search