SYBA CL-KVM-281 KVM switch
Contents
1. 2 port USB KVM Switch 4 port USB KVM Switch are Installation Please read this important installation information Never mix DVI with VGA If the input connections are VGA the output must be VGA and vice versa KVM will not display if inputs output are mixed Boot your systems one at a time and during the boot up make sure that you are monitoring the LEDs on the face of the KVM unit If you notice that the LED switches to the other channel then press the channel button under the correct boot channel Example If you are booting 2 and it switches to 1 press the button under 2 Keep monitoring the KVM unit until the systems are done with their boot up sequence Windows 98 98SE user When you apply Windows 98SE to USB KVM Switch please use the following set up procedures us otep 1 Connecting USB cable type A connector to PC USB por 2 Connecting VGA HDB15 pin Male to Female cable to PC connecting DVI D 18 1key Male to Male cable to PC 3 VGA DVI monitor s cables are connected to USB KVM Switch s console VGA DVI port 4 Connecting the enclosed USB A B cable type A to USB port of PC type B to PC port on rear side of USB KVM Switch 5 It will install USB HID Human Interface Device driver Using Keyboard Tab key Left Arrow key Right Arrow key and Enter key to accomplish set up process 6 To Switch to the next PC port of USB KVM switch f Repeat item 5 procedure to all of PCs 2nd Step 12. Connecting USB keyboard and USB mouse to USB KVM Switch s console USB port on front of switch Windows ME XP NT 2000 user When you apply Windows ME XP NT 2000 to the USB KVM switch please use the following set up procedure 1 Connecting the enclosed USB A B cable type A to USB port of PC type B to PC port on rear side of USB KVM Switch 2 Connecting VGA HDB15 pin Male to Female cable to PC connecting DVI D 18 1key Male to Male cable to PC 3 VGA DVI monitor cables are connected to VGA DVI port of USB KVM Switch 4 Connecting USB keyboard to USB KVM Switch s USB port on front panel 5 Connecting USB mouse to USB KVM Switch s USB port on front panel Hot Key Definition To send commands to the USB KVM Switch the NumLock key must be pressed twice within 2 seconds If you have not pressed any key in hot key mode within 2 seconds the keyboard will back to under Operating System control state Note means press key within 2 seconds e c Switch to Previous Channel Switch to Next Channel To select PC1 Beeper OWON Audible feedback when beeper is On and keep the device in silent mode when beeper is Off ee ee switch port edd wlan uen buttons on switch S Auto Scan every 10 seconds ESC switches to regular key code Note Auto Scan mode only works with at least two PCs powered on simultaneously Sel auto scan rat
3. KVM SWITCH USER S MANUAL VERSION KVM481 003 Introduction The USB KVM Switch offers the possibility of sharing keyboard mouse and monitor between two four computers true USB interface to support its driver free and plug n play features which allow users to easily install and use the KVM Switch Dual monitor VGA DVI display connections are supported The DVI interface technology is tailored to modem digital Flat Panel Display it implements genuinely digital signal transmission over the cable to reduce undesired distortion from conventional analog digital conversion Robust and reliable with metal casing suitable for use in environments pervasive with electromagnetic interference and wherever a sturdy protective metal case is needed Features e Dual display monitor TFT LCD connection VGA DVI e USB mouse amp keyboard interface supported e Supports stereo audio sound e Direct channel selection operation and keyboard hotkeys e Supports Windows 98SE ME 2000 XP Vista Linux Mac OS e Hot Plug add or remove connected PCs for maintenance without powering down the KVM switch or PCs No software required e Auto Scan function for monitoring PC operation e LED display for monitoring port status e Buzzer sound for switching port confirmation while use keyboard hotkeys e Heavy metal casing for best shielding and protection connection PC connections 2x USB A type on front of s
4. e ESC switch to regular key Normally there is one LED is always lit i e the switch is connected to this PC port for one PC port and the other PC port s LED is off when you power on KVM switch When you select one of two PCs one LED will shut down and the selected port LED Is flashing EET Trou ooting zt m ze zin um Quei Po a ust UR id Ensure that all cables are well seated Label all of cables with the number for each respective computer to avoid confusion 1 The USB KVM Switch draws the power from USB port of computers If the computers such as desktop computer laptop computer or the other computers can not support enough power to the USB KVM switch please add a DC5V 1Amp to the power jack on rear side of USB KVM switch 2 Don t press any keys on the keyboard while the selected computer is booting up Otherwise it might cause the keyboard error or keyboard is not detected at PC side 3 If the computer boots up fine and keyboard doesn t work then make sure the keyboard works when directly plugged into the computer 4 The mouse is not detected during PC boot up Make sure the mouse works when directly plug into the computer and make sure the mouse is a true USB mouse A combo USB PS 2 mouse will work just as long as it is set for USB mouse with the correct adapter If not please try another pure USB mouse 5 Avoiding moving the mouse or press
5. ing the mouse buttons when switching the port 6 Some of DVI cards may be unable to support Hot swappable For instance if you like to connect DVI display with the USB KVM switch to prevent errors and shut down please follow the steps below Before power on the DVI PC please firstly connect the DVI PC to the USB KVM Switch i e PC 1 e Push the button of selected DVI PC i e PC 1 on the front panel of USB KVM switch e Connect other devices such like speaker microphone to the USB KVM Switch e Power on the DVI PC and wait until the DVI display is well appeared e After all may change to another channel i e PC 2 PC4 if needed 7 When the console PC is power off the USB KVM switch will detect the power on PC approx 20 seconds
6. witch 2x USB A type on front of switch tor Mouse Keyboard 1x DVI 1841 Single Link Digital 1x DVI 1841 Single Link Digital only oniy 1 VGA 15 Analog 1x VGA HDB15 Analog only rien md oe ama 1x 3 5 mm Audio jack Speaker 1x 3 5 mm Audio jack Microphona Consolo port connector all female type only 2 x 15 Analog only 2x 3 5mm Audio jack Speaker 2x3 5mm Audio jack Analog only 4x3 5mm Audio jack Sponka 4 x 3 5mm Audio jack Microphone PC Port Cables 2x VGA HDB15 Male to Female 4 VGA HDB15 Male to Female cabis cables 2 DVI D 18 1 Single Link Male Ax DVI D 18 1 Single Link Male lo Male cables lo Male cables 2x USB cables included in 4x USB cables included in package package MAI ar tic iem 4x 35mm Audio Male lo Male Dimension mm Daisy Chain and Levels No Power Type EP Bus powered or DC 5V Housing Heavy metal casing A Operating Temperature Storage Temperature 20 ta 60 C Humidity USB KVM Switch 4 port 1x USB Keyboard Ix USB mouse ix VGA 1 x DVI Monitor Ix VGA 1 x DVI Monitor Microphone wi 5mm jack Microphone 3 5mm jack 1x Speaker 2 0 set w 3 5mm jack 1x Speaker 2 0 set w3 5mm jack
Download Pdf Manuals
Related Search