USER GUIDE 355 Man Down V1 - The Wireless Works
Contents
1. The Wireless Works Activating an SOS Alarm Press and hold the SOS button for 3 seconds you will hear the beep sound the green light will start to flash rapidly to confirm the request After that an SOS Alarm Help mel will be sent to all authorized phone numbers and platform In the meantime it will dial the 3 set authorized numbers The first number will take priority over the second and third If the device fails to connect to the first number it will switch to the second one if the second number fails to connect the system will connect to the third number etc if device fails to call all 3 numbers it will wait 5 minutes and then start to dial the numbers again This will continue until one of the phone numbers answers the call then two way communication will start To end the call press the SOS button Making a Phone Call To make a call press and hold the call button on the side for 3 seconds you will hear a beep sound the green light will start to flash rapidly to confirm the request and then it will dial the second number To end the call press the SOS button How to adjust sound volume when in voice contact Press the side button VOL power button and VOL call button to adjust the volume when in two way voice communication Low battery alarm When the devices battery is lower than 20 it will send a SMS alarm BAT LOW to all authorized numbers If the battery is lower than 15 the red light will fl2. When using for the first time use please fully charge the battery for around 4 hours When charging the Power LED red will be on solid After the device is fully charged the power LED red will be off P e A z The Wireless Works Switching the device on and off To turn the device on press and hold the power button for 3 seconds all LED s will flash rapidly X Please keep the unit in the open to obtain a satellite fix To turn the device off press and hold the power button for 3 seconds after you hear a beep sound the device has turned off What do the lights mean GSM LED GREEN Light shows a single flash rapidly every 3 seconds the device is connected to GSM network Light shows a double flash rapidly every 3 seconds the device is registered to GPRS network Light shows a slow flash every 3 seconds the device is connecting to GSM network Light Solid not flashing No SIM Card detected GPS LED BLUE Light shows a single flash rapidly every 3 seconds the device has GPS positioning fix Light shows a slow flash every 3 seconds 1 second on and 3 seconds off the device has no GPS fix No flashing the GPS chip is asleep Power LED RED Red On The device is charging OFF The device is not charging or has been full charged Flashing rapidly the device power lower than 15 Flashing randomly the device is on the move P 2 A z
3. will reply Add name ok X To delete name you can send named 4 Location request 4 1 Reply with coordinates and web link Command loc The device will reply GPS Info Time xxxxx Lat xxxx Lon xxxx Spd xxxxx Altitude xxxx Bt xxx maps google com maps q loc 22 647379 114 030998 XPut the coordinates in to Google earth or Google maps Click on search button to find the position of the device gt Click on the text link then the location can be shown directly on Google Map on your mobile phone po The Wireless Works 4 2 Reply with Address Command add Notes This function needs GPRS function support The device will reply Add Main Street Oxon UK 5 Cell Locate The unit can be tracked by GSM base station towers If the GPS signal is not available for example in a room the underground etc the user can be located by GSM tower However as compared to GPS satellite GSM accuracy is proven to be worse than that of GPS GSM provide triangulation techniques to try to pinpoint the location of the device GSM base stations are further affected by factors similar to GPS in the sense of the barriers affecting signal quality and the density of GSM towers to assist in the triangulation with some regional areas having errors of 100M to 2KM Command CL1 The device will reply Cell locate on To turn off this function please send CLO 6 GEO FENCE Alarm Command G X Y Z xxxM KM Example G1 1 1 100M
4. 1 Only A1 B1 C1 numbers can make a silent call to the tracker the tracker answers the call automatically and allows the caller to listen to the audio around the tracker There is no voice indication at the device that the call is in progress To turn off this function send LO to the device 10 Motion alarm no activity Command V1 xx S M H Note No space in between S means second M means minute H means hour xx means the time you set and must be two digitals Example V1 05M If the user turns on this function the device will detect no motion every 5 minutes in this example and will send SMS alarm to all registered phone numbers of a warning To turn off this function send VO 11 Shut down the 3 LEDs Battery saving Command LED1 The device will reply LED off and the LEDs will stop flashing but the device is actually running To turn off this function please send LEDO 10 P e A z The Wireless Works 12 AGPS Command AGPS1 latitude longitude Example AGPS1 22 647606 114 022583 Assisted GPS abbreviated generally as A GPS and less commonly as aGPS is a system that is often used to significantly improve the startup performance or time to first fix TTFF improving the GPS locating to be more precise of a GPS satellite based positioning system To turn off this function send AGPSO 13 Fall detection A simple fall may cause devastating consequence A Fall Sensor can help you get immediate
5. Notes No space in between X No of Geo fence 1 3 user can set 3 Geo fences Y 0 means to turn off the function Y 1 means to turn on the function Z 1 means to set alarm when the tracker enters the preset area Z 0 means to set alarm when the tracker breaches the district xxx is the preset distance to the tracker s original place must be 3 digitals M means meters KM means kilometers po The Wireless Works The device will send a message to the authorized numbers as Geo fence alarm GPS info when it enter the area you set Note The user can only set this function when tracker has a fixed GPS signal To turn off this function please send G1 0 or G2 0 or G3 0 7 Over Speed alert Command speed1 Speed Notes The speed must be in a value of speed using 2 or 3 digitals 01 255km h Example speed1 100 Suppose the over speed alert we want to set is 100km h when the device exceeds 100km h it will send message Over speed GPS Info to all preset numbers To turn off this function send speedO to the device 8 Movement Alert Command M1 xxxM KM Notes xxx is the preset distance to the devices original place must be 3 digitals M means meters KM means kilometers Example m1 100m When the tracker moves out of 100 meters it will send SMS alarm to the preset numbers To turn off this function please send MO to the device no The Wireless Works 9 Listen in Voice wiretapping Command L
6. ash rapidly to warn the user to charge the device as soon as possible no The Wireless Works Configuration and Operation by SMS 1 To Set the Authorized Number X It is not mandatory for all three authorized numbers to be set however a minimum of one must always be set Command A1 or A1 phone number Note With no spaces in the text case insensitive Example A1 or a1 123456789 X Using your mobile phone send A1 to the phone number in the device it will reply with a message Set mobile number 1 OK X To delete this number send A0 to the device Command B1 or B1 phone number Example B1 or b1 123456789 The device will reply with a message Set mobile number 2 OK X To delete this number you can send BO Command C1 or C1 phone number Example C1 or c1 123456789 The device will reply with a message Set mobile number 3 OK X To delete this number you can send CO no The Wireless Works 2 Modify the Time zone Command TZ 00 00 Note the time amounts must be in 2 digits with a maximum 23 hours in value A in the time zone portion of the text indicates east The symbol in the time zone indicates west Example tz 02 the system will add 2 hours based on the UTC time tz 02 the system will minus 2 hours based on the UTC time X UTC time has been set as default time 3 User defined name in SMS content Command namel user name Example namel Emma the device
7. d temperatures 4 Clean the unit with a piece of dry cloth Don t use any chemicals or detergents 5 Do not disassemble or refit the unit 6 Do not attempt to replace the battery 14 po The Wireless Works Hardware Specification Specification Mainframe Dimension 61mm 43mm 16mm Weight 35g GSM Frequencies 900 1800mhz 850 1900Mhz GPS chip U blox 7 Support AGPS GPS sensitivity Cold start 148dBm Hot start 162dBm GPS accuracy lt 2 5m Time to First Fix Cold start 32s Warm start 11s Hot start 1s Charging Voltage 5V DC Battery Chargeable 3 7V 900mAh Standby Current lt 2mAh Storage Temperature 40 C to 85 C Operation Temperature 20 C to 80 C Humidity 5 95 non condensing 15
8. en device isn t moving Under normal use the battery can last 3 7 days 3 Deep Sleeping mode Command DS1 or DS1 xxM H Both GSM and GPS chip will shut down to save power during deep sleeping the device is unable to receive any phone calls or SMS messages It can be only activated by motion sensor Once motion is detected the device will run for the time you set and then sleep again if no motion is detected The battery can last up to 40 days if no motion is detected To turn off this function send DSO 12 po The Wireless Works 4 GPRS Setting In order to use the GPRS function the user needs to setup the APN by sending SMS command What is an APN Access point name APN is the name used to identify a general packet radio service GPRS bearer service in the GSM mobile network The APN defines the type of service that is provided in the packet data connection X Make sure that the SIM card in the device supports GPRS function gt lt The APN can be acquired from your local GSM operator Command S1 APN user name password Notes Some access points don t use a user name or password if so leave it blank Example S1 internet internet is the APN from the SIM card provider therefore the user must set their particular APN for their own country which the unit resides After sending the command the device will reply Set APN OK GPRS connecting After sending S1 APN allow several minutes bef
9. help Command FL1 or FL2 or FL3 or FL4 or FL5 or FL6 or FL7 or FL8 or FLO 1 means very high sensitivity 2 means high sensitivity 3 means medium high sensitivity 4 means medium sensitivity 5 means medium sensitivity etc 9 means the very lowest sensitivity The device must senses both impact and angle after that the device must remain in a lying position for 10 seconds before it will raise an alarm To turn off this function please send FLO 14 Check settings Command status The device will reply E g A 8613812345678 B13912345678 C13712345678 Speed 0 100km h GEO 0 0 0 VB 1 10S MV 1 100 LBS 1 LED 0 TZ 2 0 LI 1 PS 1 DS 0 FL 1 Bat 95 To recognize the meaning of 0 amp 1 The number 0 implies that the function is turned off whilst 1 indicates that the function is turned on 11 po The Wireless Works The Device has three working power modes 1 No Power saving mode Command PSO In this mode both the GSM and GPS chips will keep working to fix signals all the time The battery can last 18 24 hours 2 Smart Power saving mode default mode Command PS1 Under this mode the device uses its built in motion sensor to detect movement The GSM chip is always working to receive calls SMS messages and transmit location information The GPS chip activates by motion an incoming call or SMS The GPS chip is off when there is no motion or calling or SMS The battery life is extended wh
10. k ONE 4 The Wireless Works USER GUIDE 355 MD GSM Personal Asset GPS TRACKING SYSTEM The Wireless Works Product Overview This device is an innovative miniature size personal remote positioning device with built in U blox GPS and GSM GPRS technology for monitoring and protecting people and property It can be used in all walks of life from traveling lone workers mobile nursing staff children the elderly and persons with dementia etc What s New 1 Unique design combining style and technology 2 Supports A GPS for accelerated positioning 3 Supports GPS and Cellular tracking 4 Two way voice communications 5 Fall detection via 3D G sensor 6 Firmware upgrade over the air 7 Built in 8MB flash memory 8 GPRS blind area data re upload function What s in the box This device is supplied in a box which includes GSM Device USB Charging cable USB Mains Charger e e A 4 The Wireless Works Getting to know your device SOS BUTTON MICROPHONE SS MICRO USB gt SIM SLOT ON OFF amp CALL LED INDICATORS SIM card Installation The SIM card is not included in the package Micro SIM cards are available from mobile phone network operators Lift SIM card cover and insert the SIM card by the direction of the picture shows Note position of SIM card Note Before installing the SIM card please make sure the SIM card has no PIN code lock First time usage
11. ore the device will be visible online Set GPRS Time interval by SMS Command TIxxS M H The meaning of xx the setting must be in 2 digitals and a maximum 99 in value which means 01798 xxS is the time interval in second with range 30 99 xxM is the time interval in minute with range 01 99 xxH is the time interval in hour with range 01 99 Example TI01M The device will reply Set updating time interval OK and then device will update the time by every 1 minute on the website Disable GPRS Command SO The device will reply GPRS OFF 13 po The Wireless Works Reconnect GPRS To reconnect to the website via GPRS for real time tracking send S2 Reboot device Command reboot The device will restart without changing any settings Initialization Command RESET Note This will reset all settings back to factory default Built in Memory The device has a built in 8MB flash memory It will store the GPS information when the device does not have GSM network coverage i e very low population density areas some mountainous terrain underground areas etc The device will transmit GPS locations to the WEB server automatically once the GSM network is recovered Caution Please comply with the instructions to extend the unit life 1 Keep the unit dry Any liquid may destroy or damage the device 2 Do not use amp store the unit in dusty places 3 Do not expose the device to extreme hot or col
Download Pdf Manuals
Related Search