Samsung SM320MXN-2
Contents
1. the set will be rebooted automatically How can I change the frequency The frequency can be changed by reconfiguring the video card Note that video card support can vary depending on the version of the driver used Refer to the computer or the video card manual for details How can I Adjusts the resolution Windows XP Set the resolution in the Control Panel Appearance and Themes Display Settings Windows ME 2000 Set the resolution in the Control Panel Display Settings Contact the video card manufacturer for details How can I set the Power Saving function Windows XP Set the resolution in the Control Panel Appearance and Themes Display Screen Saver Set the function in the BIOS SETUP of the computer Refer to the Windows Computer Man ual Windows ME 2000 Troubleshooting Set the resolution at the Control Panel Display Screen Saver Set the function in the BIOS SETUP of the computer Refer to the Windows Computer Man ual How can I clean the outer case LCD Panel Disconnect the power cord and then clean the LCD Display with a soft cloth using either a cleaning solution or plain water Do not leave any detergent or scratches on the case Do not let any water enter the LCD Display How can I play the video The video supports the MPEGI1 and WMV codecs only Install the corresponding codec to play the video Note that some of the codecs can be incompatibl2. port on the back of the LCD Display Trun on the power switch There are 2 ways to connect the D sub to your LCD Display Choose one of the following Using the D sub Analog connector on the video card e Connect the D sub to the 15 pin RGB port on the back of your LCD Display and the 15 pin D sub Port on the computer Using the DVI Digital connector on the video card e Connect the DVI Cable to the DVI port on the back of your LCD Display and the DVI port on the computer Connections Connect the audio cable for your LCD Display to the audio port on the back of your computer Note e Turn on both your computer and the LCD Display e The DVI cable is optional e Contact a local SAMSUNG Electronics Service Center to buy optional items Connecting to Other devices sing a Power cord with Earth e In the event of failure the earth lead may cause electric shock Make sure to wire the earth lead in correctly before connecting the AC power When un wiring the earth lead make sure to disconnect the AC power in advance Note AV input devices such as DVD players VCR s or camcorders as well as your computer can be con nected to the LCD Display For detailed information on connecting AV input devices refer to the contents under Adjusting Your LCD Display Connecting AV Devices 1 Connect the port of the DVD VCR DVD DTV Set Top Box to the R AUDIO L port of the LCD Display 2 The
3. to the HDMI terminal of the LCD Display using a DVI to HDMI cable e Connect the red and white jacks of an RCA to stereo for PC cable to the same colored audio output terminals of the digital output device and connect the opposite jack to the DVI PC HDMI AUDIO IN terminal of the LCD Display Connecting to an Audio System AUX 06 ER Note e Connect a set of audio cables between the AUX L R jacks on the AUDIO SYSTEM and AUDIO OUT L AUDIO R on LCD Display Connecting a LAN Cable sing a Power cord with Earth e In the event of failure the earth lead may cause electric shock Make sure to wire the earth lead in correctly before connecting the AC power When un wiring the earth lead make sure to disconnect the AC power in advance Note AV input devices such as DVD players VCR s or camcorders as well as your computer can be con nected to the LCD Display For detailed information on connecting AV input devices refer to the User Controls under Adjusting Your LCD Display Connections Note Connect the LAN cable Applicable to the MXn model only Connecting a USB device sing a Power cord with Earth e In the event of failure the earth lead may cause electric shock Make sure to wire the earth lead in correctly before connecting the AC power When un wiring the earth lead make sure to disconnect the AC power in advance Note AV input devices such as DVD players
4. when using it in a public place The locking device has to be purchased separately The appearance and locking method may differ from the illustration depending on the manufacturer Refer to the manual provided with the Kensington Lock for proper use The locking device has to be purchased separately Note The location of the Kensington Lock may be dif ferent depending on its model Using the Anti Theft Kensington Lock 1 Insert the locking device into the Kensington slot on the Monitor Onn turn it in the locking direction 2 Connect the Kensington Lock cable 3 Fix the Kensington Lock to a desk or a heavy stationary object Note See Connecting Cables for further information regarding cable connections Remote Control Note The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display causing a malfunction due to interference with the frequency Introduction power Oorr Number Buttons DEL button VOL ok MUTE TV DTV F MENU i INFO COLOR BUTTONS ESLA TTX MIX STILL SAMSUNG AUTO S MODE MDC LOCK SOURCE ENTER PRE CH Y CHP A D MENU GUIDE I RETURN Up Down Left Right buttons exit SRS MagicInfo P MODE H DUAL MTS PIP SWAP SGeEeeeeeeeeseseseeoeoeoeeeeoconooeeseoooddd 6d 1 4 POWER Turns the product On 2 O off Turns the product Off 3 Number Buttons Press to change th
5. 320MX 320MXn Introduction Package Contents Note Please make sure the following items are included with your LCD Display If any items are missing contact your dealer Contact a local dealer to buy optional items E Note This stand is not for the Floor Standing Type Unpacking LCD Display Manuals Quick Setup Guide Warranty Card User s Guide Not available in all loca tions Cables D Sub Cable Power Cord Others Introduction Others Remote Control Batteries AAA X 2 Not available in all loca tions Sold separately DVI Cable Wall Mount KIT LAN Cable Applicable to the MXn mod el only TV tuner box NetWork Box A i Applicable to the MX model Semi Stand KIT only Note e You can purchase and connect a separate network box or TV tuner box For information on how to use these refer to their respective user manuals e You can only connect one external box Your LCD Display Front MENU button MENU Rear Introduction Opens the on screen menu and exits from the menu Also use to exit the OSD menu or return to the previous menu Navigate buttons Up Down buttons Moves from one menu item to another vertically or adjusts selected menu values Adjust buttons Left Right buttons Volume buttons Moves from one menu item to another horizontally or adjusts selected menu val ues When OSD is not on the screen push the button to adjust volume ENTER button ENTE
6. Q The screen is blank and the power indicator is off A Ensure that the power cord is firmly connected and the LCD Display is on Refer to the Connecting a Computer Check Signal Cable message Ensure that the signal cable 1s firmly connected to the PC or video sources Refer to the Connecting a Computer Ensure that the PC or video sources are turned on Not Optimum Mode message Check the maximum resolution and the frequency of the video Adaptor Compare these values with the data in the Preset Timing Modes Chart The picture rolls vertically Pr PF FF OD Pe Check if the signal cable is securely connected Re connect it if necessary Refer to Connecting a Computer The image is not clear picture 1s blurred Run Frequency Coarse and Fine tuning Turn on again after removing all accessories video extension cable etc Set the resolution and frequency to the recommended ranges The picture image is unstable and shakes gt PF PF F Check if the resolution and frequency set for the computer video card falls in the range supported by the LCD Display Ifnot reset them referring to the current Information under the LCD Display menu and Preset Timing Modes Ghost images are shown in the picture Check if the resolution and frequency set for the computer video card falls in the range supported by the LCD Display Ifnot reset them referring to the current Information under the LCD Display menu and Preset T
7. R Activates a highlighted menu item SOURCE button SOURCE Switches from PC mode to Video mode Changing the source is only allowed for external devices that are connected to the LCD Display at the time DVI AV HDMI MagicInfo TV PC Note e The TV menu is available when a TV tuner box is installed e The MagicInfo menu is available when a network box is installed in the MXn or MX model D MENU Opens the on screen D MENU Note e This is available when a TV tuner box is installed Power indicator Shows PowerSaver mode by blinking green Note See PowerSaver described in the manual for further information regarding power saving functions For energy conservation turn your LCD Display OFF when it is not needed or when leaving it unattended for long periods Remote Control Sensor Aim the remote control towards this spot on the LCD Display Note For detailed information concerning cable connections refer to Connecting Cables under Setup The LCD Display s configuration at the back may vary slightly depending on the LCD Display model Introduction power S W ON OFF 0 Switches the LCD Display On Off B POWER IN The power cord plugs into the LCD Display and the wall plug ks232C OUT IN RS232C Serial PORT MDC Multiple Display Control Program Port O DVI PC HDMIIN DVI PC HDMI AUDIO IN PC DVI HDMI Audio Connection Terminal Inpu
8. VCR s or camcorders as well as your computer can be con nected to the LCD Display For detailed information on connecting AV input devices refer to the User Controls under Adjusting Your LCD Display Note You can connect USB devices such as a mouse or keyboard Applicable to the MXn model only Troubleshooting Self Test Feature Check A note Check the following items yourself before calling for assistance Contact a Service Center for problems that you cannot solve by yourself Self Test Feature Check 1 Turn off both your computer and the LCD Display 2 Unplug the video cable from the back of the computer 3 Turn onthe LCD Display The figure shown below Check Signal Cable appears on a black background when the LCD Display is working normally even though no video signal is detected While in the Self Test mode the LED power indicator remains green and the figure moves around on the screen Samsunga Check Signal Cable PC 4 Turn off your LCD Display and reconnect the video cable then turn on both your computer and the LCD Display If your LCD Display screen remains blank after using the previous procedure check your video con troller and computer system your LCD Display is functioning properly Warning Messages You can even view the screen at a resolution of 1360 x 768 However you will receive the following message for a minute You can choose to change the screen resolution or stay in the current
9. ching Then push button again to circle through available preconfigured modes Entertain Internet Text Custom DUAL STEREO MONO DUAL DUAL Il and MONO NICAM MONO NICAM STEREO can be operated depending on the broadcasting type by using the DUAL button on the remote control while watching TV MTS You can select MTS Multichannel Television Stereo mode Audio Type MTS S_ Mode Default FM Stereo Mono Mono Manual Change Stereo Mono gt Stereo SAP Mono lt gt SAP Mono Every time you press the button a PIP screen appears This fuction does not work for this LCD Display Swaps the contents of the PIP and main image The image in the PIP window will appear on the main screen and the main screen image will appear in the PIP window This fuction does not work for this LCD Display Connections Connecting a Computer sing a Power cord with Earth e In the event of failure the earth lead may cause electric shock Make sure to wire the earth lead in correctly before connecting the AC power When un wiring the earth lead make sure to disconnect the AC power in advance Note AV input devices such as DVD players VCR s or camcorders as well as your computer can be con nected to the LCD Display For detailed information on connecting AV input devices refer to the User Controls under Adjusting Your LCD Display Aa w Connect the power cord for your LCD Display to the power
10. computer beeps more than 3 times when booting If it does request an a service for the main board of the computer 3 Ifyou installed a new video card or if you assembled the PC check if you installed the Adaptor video 4 Check if the scanning ratio of the video screen is set to between 50 Hz 85 Hz Do not exceed 60Hz when using the maximum resolution 5 Ifyou have problems in installing the Adaptor video driver boot the computer in Safe Mode remove the Display Adaptor in the Control Panel System Device Administrator and then reboot the computer to reinstall the Adaptor video driver Check List Note e The following table lists possible problems and their solutions Before calling for assistance check the information in this section to see if you can remedy any problems for yourself If you do need assistance please call the phone number on the Information section or contact your dealer e For more network related information refer to the MagicInfo Troubleshooting section Problems related to the Installation PC Mode B note Problems related to the LCD Display installation and their solutions are listed Q The LCD Display screen flickers Troubleshooting A Check if the signal cable between the computer and the LCD Display is securely connected Refer to Connecting a Computer Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed
11. e Note Before calling for assistance check the information in this section to see if you can remedy any prob lems yourself If you do need assistance please call the phone number on the Information section or contact your dealer
12. e channel 4 DEL button 5 VOL 6 2K MUTE 7 TV DTV s E MENU g 10 I INFO 11 COLOR BUTTONS 12 43 TTX MIX 13 STILL 14 AUTO 15 SMODE 16 MDC 17 LOCK 18 SOURCE 19 ENTER PRE CH 20 VCH PA 21 D MENU 22 GUIDE 23 I RETURN Introduction The button operates only for DTV It is used to select MMS multi channel for a DTV Adjusts the audio volume Pauses mutes the audio output temporarily This is displayed on the lower left corner of the screen The audio resumes if MUTE or VOL is pressed in the Mute mode Selects the TV and DTV mode directly Opens the on screen menu and exits from the menu or closes the adjustment menu Activates a highlighted menu item Current picture information is displayed on the upper left corner of the screen Press to add or delete channels and to store channels to the favorite channel list in the Channel List menu TV channels provide written information services via teletext Teletext Buttons 00 0ga 06 0 0a 00a a 0a 0m For more information gt TTX MIX Press the button once to freeze the screen Press it again to un freeze Adjusts the screen display automatically in PC mode By changing the resolution in the control panel auto function is performed When pressing this button the current mode is displayed at the bottom centre of the screen The LCD Display has a built in high fidelity stereo amp
13. iming Modes Q The image is too light or too dark Adjusts the brightness and contrast Refer to the Brightness Contrast Q The screen color is inconsistent gt Fy Dy 2 FF 2 es fF Troubleshooting Adjust color using Custom under OSD Color Adjustment menu The color image is distorted by dark shadows Adjust color using Custom under OSD Color Adjustment menu The color white is poor Adjust color using Custom under OSD Color Adjustment menu The Power Indicator blinks The LCD Display is currently saving the changes made in the settings to the OSD memory The screen is blank and the power indicator light blinks every 0 5 or 1 seconds The LCD Display is using its power management system Press any key on the keyboard The screen is blank and it is blinking If you see the TEST GOOD message on the screen when you pressing the MENU button check the cable connection between the LCD Display and the computer to ensure that the con nector is properly connected Problems related to Audio Note Problems related to audio signals and their solutions are listed below Q A ym Q Q No sound Ensure that the audio cable is firmly connected to both the audio in port on your LCD Display and the audio out port on your sound card Refer to the Connecting a Computer Check the volume level The sound level is too low Check the volume level If the volume is still too low after turning the control to i
14. lifier Then press the button again to circle through available preconfigured modes Standard Music Movie Speech Custom MDC Quick Launch Button Activates or deactivates all function keys on both the remote con trol and the LCD Display except for the Power and LOCK buttons Press the button to change the input signal SOURCE Changing the SOURCE is only allowed for external devices that are connected to the monitor at the time This button is used to return to the immediately previous channel In TV mode selects TV channels DTV menu display Electronic Program Guide EPG display Returns to the previous menu 24 Up Down Left Right but tons 25 7 ll EXIT 26 0 srs 27 MagicInfo 28 P MODE 29 Hl DUAL MTS 30 PIP 31 SWAP Introduction Moves from one menu item to another horizontally vertically or adjusts selected menu values Exits from the menu screen Not Available MagicInfo Quick Launch Button When you press this button current picture mode is displayed on the lower center of the screen AV HDMI TV P MODE The LCD Display has four automatic picture settings that are pre set at the factory Then push button again to circle through avail able preconfigured modes Dynamic Standard Movie Custom PC DVI MagicInfo M B MagicBright MagicBright is a feature providing the optimum viewing envi ronment depending on the contents of the image you are wat
15. mode during that time And if the resolution is more than 85Hz you will see the black screen because the LCD Display does not support over 85Hz Not Optimum Mode Fecommended Mode AREAS KX A GOH Note Refer to Specifications gt Preset Timing Modes for the resolutions or frequencies supported by the LCD Display Maintenance and Cleaning 1 Maintaining the LCD Display Case Clean with a soft cloth after disconnecting the power cord Troubleshooting e Do not use benzene thinner or other flammable substan ces or a wet cloth e Werecommend that a SAMSUNG cleansing agent is used to prevent damage to the screen 2 Maintaining the Flat Panel Display Screen Clean with a soft cloth cotton flannel smoothly e Never use acetone benzene or thinner ts lsg They may cause flaws or deformation of the screen sur face e The user will be required to pay costs and related expenses for repairing damages caused Symptoms and Recommended Actions Note A LCD Display recreates visual signals received from the computer Therefore if there is a problem with the computer or the video card this can cause the LCD Display to become blank have poor coloring become noisy and video mode not supported etc In this case first check the source of the problem and then contact a Service Center or your dealer 1 Check if the power cord and the video cables are properly connected to the computer 2 Check if the
16. n start the DVD VCR or Camcorders with a DVD disc or tape inserted 3 Select AV using the SOURCE Note The LCD Display has AV connection terminals to connect AV input devices like DVDs VCRs or Camcorders You may enjoy AV signals as long as the LCD Display is turned on Connections Connecting to a Camcorder an we oe 4 ty Ao lal A WS OUTPUT AUDIO VIDEO 0 1 Locate the A V output jacks on the camcorder They are usually found on the side or back of the camcorder Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the AV AUDIO IN L AUDIO R on the LCD Display 2 Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV IN VIDEO on the LCD Display 3 Select AV for the Camcorder connection using the Source button on the front of the LCD Display or on the remote control 4 Then start the Camcorders with a tape inserted Note The audio video cables shown here are usually included with a Camcorder If not check your local electronics store If your camcorder is stereo you need to connect a set of two cables Connecting Using a HDMI Cable Note e Input devices such as digital DVD are connected to the HDMI terminal of the LCD Display using the HDMI cable e You cannot connect a PC to the HDMI terminal Connections Connecting Using a DVI to HDMI Cable Note e Connect the DVI output terminal of a digital output device
17. t DVI PC HDMI IN HDMI Connect the HDMI terminal at the back of your LCD Display to the HDMI terminal of your dig ital output device using a HDMI cable DVI PC HDMI IN RGB PC Video Con nection Terminal Using a D Sub Cable 15 pin D Sub PC mode Analog PC B DVI PC HDMI IN DVI PC Video Con nection Terminal Using a DVI Cable DVI D to DVI D DVI mode Digital PC Introduction DC POWER OUT Power Connect this to the POWER connector of a TV tuner box or network box VIN VIDEO VIDEO Connection Termi nal Connect the VIDEO terminal of your monitor to the video output terminal of the external device using a VIDEO cable AV AUDIO IN L AUDIO R LCD Display Audio Connection Terminal Input AV AUDIO OUT L AUDIO R LCD Dis play Audio Connection Terminal Output O ros OUT Applicable to the MXn model only viv LAN Connection Terminal Applicable to the MXn model only USB USB Connection Terminal Keyboard Mouse Mass Storage Device Com patible Applicable to the MXn model only Note The number of LCD Displays that can be con nected to loopout may differ depending on the cables signal source etc With cables where there is no degradation or signal source up to ten LCD Displays can be connected Introduction Kensington Lock The Kensington Lock is a device used to physi cally fix the system
18. ts maximum check the volume control on the computer sound card or software program The sound is too high or too low Adjusts the Treble and Bass to the appropriate levels Problems related to the Remote Control Note Problems related to the remote control and their solutions are listed Q A A The remote control buttons do not respond Check the polarities of the batteries Check if the batteries are empty A A A Troubleshooting Check if the power is on Check if the power cord is securely connected Check if a special fluorescent or neon lamp is on in the vicinity Problems related to Magiclnfo Note Making a Bootable USB Flash Disk Q amp A Q A Making a Bootable USB Flash Disk 1 You can turn a common 512 MB or bigger USB storage media into a bootable disk using a USB bootable disk creation tool For example the HP USB Disk Storage Format Tool 2 Copies the OS ghost image and executables to your USB disk 3 Enter the BIOS menu of your set by pressing the F2 key in the BIOS logo screen Then enable the USB Boot First option by selecting that option and pressing the Enter key in the Boot menu 4 Switch your set on while your USB disk is connected and boot up in DOS mode 5 Run C ghost exe and choose Local Partition From Image from the menu Choose the ghost image to update your USB disk with and choose the target disk 6 When the ghost image update finishes
Download Pdf Manuals
Related Search