CRU 2 Bay Enclosure SCSI Ultra F/W 160
Contents
1. CRI Rugged Reliable Mobile Secure DataPort 2 and 4 Bay Enclosure Install Guide The DataPort 2 and 4 Bay SCSI Enclosures allow external SCSI devices to be easily added to any system with an available external SCSI channel The DataPort Enclo sures Can provide additional tape backup units CD ROMs or non removable hard drives to a server The DataPort 2 and 4 Bay Enclosures will support most full height SCSI tape backup units For adding removable DataPort hard drives please contact CRU at www CRU DataPort com SSS Ol The DataPort 2 amp 4 Bay Enclosures include the following pieces If any items are missing or damaged please contact CRU for a replacement 3 Set the SCSI ID on the device or remove the jumpers and use the provided SCSI ID selector switch Do not use SCSI ID 7 it 4 Bay Enclosure Package Contents is used by SCSI Host Bus Adapters 1 External Enclosure 4 Install the hard drive mounting kits and secure them with the 1 U320 LVD Terminator provided screws Otherwise install the SCSI device into the them with th l 1 External U320 VHD to UVHD Cable enclosure and secure them with the provided screws 4 Hard Drive Mounting Rails 5 Connect the data and power cables to the back of the SCSI devices If needed connect the SCSI ID selector switches 1 Installation Guide a 6 Slide the cover back on and secure It with the screws 2 Bay Enclosure Package Contents 7 Connect th2. e external power cable the SCSI cable and 1 External Enclosure Terminator 1 U320 LVD Terminator 1 External U320 VHD to UVHD Cable 2 Hard Drive Mounting Rails Your enclosure is now setup and ready for use 1 Installation Guide Enclosure Set Up 1 Remove the cover of the DataPort Enclosure Remove the rear screws and slide the cover off the back of the enclosure 2 Remove the front bezels if you are installing a device that needs external access such as a tape back up unit or CD ROM gt 1 800 260 9800 gt www CRU DataPort com Un Operation For best results power on your SCSI Enclosure before powering on your computer system The power switch is located on the bottom front of the enclosure The DataPort SCSI Enclosure is also equipped with 2 or 4 external SCSI ID selector switches These allow you to externally set the SCSI ID number from the back of the enclosure There are two buttons on each switch for increasing or decreasing the SCSI ID number Make sure the SCSI device is set to zero before using the selector on the back of the enclosure Please note that while the CRU DataPort 4 bay enclosure has 5 avail able bays it is currently cabled to support 4 SCSI devices Technical Support Contact your dealer for technical support first If you still need assistance contact the CRU DataPort technical support depart ment You can contact our technical support department by visiting our web site at http
3. ma tion or data computer malfunction or any other special indirect consequential or incidental damages arising in any way out of the sale of use of or inability to use any CRU product or service even if CRU has been advised of the possibility of such damages In no case shall CRU s liability exceed the actual money paid for the products at issue CRU reserves the right to make modifica tions and additions to this product without notice or taking on additional liability Register your product at www CRU DataPort com As 024 0001 Rev 1 1 gt 1 800 260 9800 gt www CRU DataPort com
4. www CRU DataPort com sending an E mail message to support CRU DataPort com or calling technical support at 800 260 9800 during the hours of 8 00 AM to 5 00 PM PST Monday through Friday When you call please have the following information ready e The part number of your CRU DataPort product s e The manufacturer s name and model number of the hard disk drive and the computer system you are using e The name of the dealer from which you purchased your CRU product s e Any error messages that appeared on your screen Rugged Reliable Mobile Secure Product Warranty CRU DataPort CRU warrants the DataPort 2 amp 4 bay enclosure to be free of significant defects in material and workmanship for a period of one year from the original date of purchase CRU s warranty is nontransferable and is limited to the original pur chaser Limitation of Liability The warranties set forth in this agreement replace all other war ranties CRU expressly disclaims all other warranties including but not limited to the implied warranties of merchantability and fitness for a particular purpose and non infringement of third party rights with respect to the documentation and hardware No CRU dealer agent or employee is authorized to make any modification extension or addition to this warranty In no event will CRU or its suppliers be liable for any costs of procurement of substitute products or services lost profits loss of infor
Download Pdf Manuals
Related Search