CRU DataPort Dual Port 25 SAS
Contents
1. CRI Rugged Reliable Mobile Secure DataPort 25 Dual Port SAS Install Guide The DataPort 25 Dual Port SAS is a high performance small form factor enclosure designed to make any capacity 2 5 SAS or SATA HDD removable from a 3 5 peripheral bay SAS provides the highest levels of performance and reliability The DataPort 25 Dual Port SAS can support Dual Port SAS operation with a SAS drive The DataPort 25 Dual Port SAS can also support a single SATA drive or when used with the DataPort 25 dual drive SATA carrier two SATA drives Package Contents 1 DataPort 25 SAS frame assembly 1 DataPort 25 SAS carrier assembly o A see 7502 252 71 REV A Pb CRU DataPort 100 e1200e2 001 4 M3 x 4mm Phillips pan head screws for hard drive mounting p MADE N TAWAN a0 4 M3 x 5mm Phillips pan head screws for frame mounting with ie rails e 4 M3 x 4mm Phillips pan head screws for frame mounting in case n SRONA JP9 Power Connector 2 M3 x 4mm Phillips pan head screws for carrier cover mounting Port 1 Port 2 2 Keys for lock Figure 1 Back of Frame Installing the Frame Into Your Computer 4 Connect the data cables to the rear of the frame See Operations sec 1 Locate an available external 3 5 drive bay and remove the front bezel tion for details on proper cabling 2 To mount the frame assembly in the drive bay Your frame assembly is complete a Check the drive bay to see if mounting rails are required they Inst2. alling a Hard Disk Drive in Your DataPort 25 Carrier should be provided by your computer system manufacturer If required install one on each side of the frame Then slide the 1 Remove the two screws that hold the cover and slide the cover off frame in the computer and check that it is secure Note Do NOT use screws longer than those supplied as the hard b If mounting rails are not required attach the frame directly to disk drive will be damaged the PC case using the screws provided Either the side or bot tom mount holes on the frame may be used 2 Connect the hard drive to the connector on the circuit board Use the provided screws to secure the hard drive The Activity LED is normally on when the hard disk drive is ready and will flash during drive activity Note The DataPort 25 dual port carrier supports SAS SATA and SATA Flash drives up to 15 4 mm in height 3 Locate and connect an available 4 pin power connector the type used for floppy drives to the back of the DataPort 25 frame For SAS drive operation 12 volt power Is required gt 1 800 260 9800 gt www CRU DataPort com Un Figure 2 Installing Hard Drive 3 Slide the cover back on to the carrier and secure it with the cover screws 4 Once the carrier has been seated in the frame the key lock must be turned 90 degrees horizontal to engage the lock and enable the power Operation Warning Please do not touch the connector on the back of the car
3. onflict with the hard disk drive status Note The green LED will flash if an incorrect data cable for the carrier is connected For single port SAS use remove the jumper on JP9 see Figure 1 and use SAS SATA port 1 JP4 Product Warranty CRU DataPort CRU warrants the DataPort 25 to be free of significant defects in material and workmanship for a period of three years from the original date of purchase CRU s warranty is nontransferable and is limited to the original purchaser Limitation of Liability The warranties set forth in this agreement replace all other warran ties CRU expressly disclaims all other warranties including but not limited to the implied warranties of merchantability and fitness for a particular purpose and noninfringement of third party rights with respect to the documentation and hardware No CRU dealer agent or employee is authorized to make any modification extension or addition to this warranty In no event will CRU or its suppliers be liable for any costs of procurement of substitute products or services lost profits loss of information or data computer malfunction or any other special indirect consequential or incidental damages arising in any way out of the sale of use of or inability to use any CRU product or service even if CRU has been advised of the possibility of such damages In no case shall CRU s liability exceed the actual money paid for the products at is sue CRU reserves the
4. rier Internal damage could result from electrostatic dis charge The lock on the DataPort 25 serves as a power switch It must be en gaged for the DataPort 25 to power up and function properly SATA Operation The DataPort 25 dual port SAS frame can be used with the DataPort 25 SATA carrier with SATA hard drives For Serial ATA operation the lower drive is supported by the left SATA connector on the rear of the frame JP4 The upper drive is supported by the right SATA connector on the rear of the frame JP5 SAS Operation The DataPort 25 Dual Port SAS frame supports dual SAS operation To enable the dual port SAS operation the frame must be connected to two different hosts The dual port SAS operation provides redundant host Support for the drive In the event of a host failure dual port SAS units will continue to store data For single port SAS operation with the DataPort 25 Dual Port SAS frame connect the data cable to either SAS SATA port 1 or port 2 gt 1 800 260 9800 Rugged Reliable Mobile Secure LED Activity The front of the DataPort 25 has two LEDs a green LED that lights up when the power to the hard drive is on and an amber LED that flashes when the drive is active provided the hard disk drive supports the LED Note lo make the host drive the activity LED connect the host LED driver to JP7 on the DataPort 25 frame Connect the host LED activity to pin 1 and the ground to pin 2 This feature may c
5. right to make modifications and additions to this product without notice or taking on additional liability Register your product at www CRU DataPort com As 025 0008 Rev 1 0 gt www CRU DataPort com
Download Pdf Manuals
Related Search