KRAM Igni-Box for 2G Drive & Talk
Contents
1. IGNI BOX FOR THE PROFESSIONAL INSTALLER Technical Specifications Voltage supply range 10 16 VDC Current usage lt 1 mA passive 2MA 3A active Activation voltage Active gt 10VDC Passive lt 10VDC Maximum current supplied by ignition 1A Active when High Measurements pr Second gt 3500 Size L x W x H Connector configurations 75x 20x 14mm Input connector Output connector 4 4 gt 2 gt z2 x Made in Denmark by Kram Telecom A S See our complete Radio Mute program on our website www kram dk IGNI BOX FOR THE PROFESSIONAL INSTALLER Product Description 69600 IGNI BOX and IGNI BOX adaptor The IGNI BOX makes the need for an ignition wire when in Stalling aftermarket car accessories redundant Many new cars do not have an easy accessible switched igni tion wire due to the use of Bus based vehicle control net works like CAN bus This has spawned the need for a fast and versatile Ignition substitute For this reason we have invented the IGNI BOX This small microprocessor controlled unit makes an artificial switched Ignition based on the noise levels on the constant 12v wire To make the needed calculations the IGNI BOX makes up to 4000 measurements pr second The IGNI BOX will switch on the ignition signal when the en gine is turned on On some car models it will even turn on the ignition signal as soon as the key is inserted into the igni tion barrel and that wa2. tart up Please wait while the IGNI BOX programs itself When the programming phase is complete after approximately 30 sec the ignition will go off Ignition wire goes low and the carkit should shut down NOTE Please avoid interfering with the cars wiring loom or electronics while the IGNI BOX is programming itself Please make a function check The blue artificial ignition wire in the 8 pin output connector should source 12v within 5 30 sec after the engine is started And should source Ov 5 30 sec after the engine is turned off In some car models the IGNI BOX will also be able to source 12v if the key is in the ignition but the engine is off NOTE If the IGNI BOX does not work as described please disconnect the IGNI BOX and repeat installation from point Zi Note If the car is equipped with accessories like Follow me home light or other systems that might be active when the car is parked Please make sure these systems are active when installing the IGNI BOX IGNI BOX FOR THE PROFESSIONAL INSTALLER 69600 for 2 G Drive amp Talk Interface leads Step 1 Prepare the installation of the IGNI BOX Do NOT connect the IGNIBOX Step 2 Start the car Step 3 Wait for warning lights to turn off and let the engine run for approxi mately 10 sec Step 4 Turn of the car and pull out the key and wait approximately 10 sec Step 5 Connect the IGNI BOX and wait approximately 30 sec
3. y being very similar to the normal ig nition functionality in older cars A normal IGNI BOX item number consists of two items The 1st item is the IGNI BOX and the 2nd item is the IGNI BOX adaptor The IGNI BOX adaptor makes the installation plug and play when installing a Kram Telecom cable set Some IGNI BOX adaptors even exists for OEM Carkit cablesets But all the IGNI BOX really needs in order to make an artificial ig nition signal is a connection to the constant 12v and the ground wire The installation is that simple EN950 IGNI BOX FOR THE PROFESSIONAL INSTALLER Installation description IGNI BOX and IGNI BOX adaptor Needed items A IGNI BOX B IGNI BOX adaptor C Cable set D Carkit adaptor Installation Installation steps 1 to 7 must be followed as described to ensure correct function of the IGNI BOX 1 Prepare the installation of the IGNI BOX Install the cable set G Refer to the instruction delivered with the Cable set If connected disconnect the Carkit adaptor from the Cable set C Connect the IGNI BOX adaptor 8 to the 8 pin connector on the IGNI BOX A NOTE Do NOT connect the IGNI BOX to the cable set Start the engine Wait for warning lights to turn off and let engine run for approximately 10 sec Stop the engine remove the key and wait approximately 10 sec Connect the IGNI BOX When the IGNI BOX is connected the ignition goes on Ignition wire goes high and the carkit should s
Download Pdf Manuals
Related Search