Edimax Fast Ethernet PCI Adapter
Contents
1. 10 100Mbps PCI Fast Ethernet Adapter EN 9130TXA User s Manual FCC COMPLIANCE STATEMENT This equipment has been tested and found to comply with the limits of a Class B computing devices pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications If you suspect this product is causing interference turn your computer on and off while your radio or TV is showing interference If the interference disappears then when you turn the computer off and reappears then you turn the computer on something in the computer is causing interference You can try to correct the interference by one or more of the following measures Reorient Relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit difference from that to which the receiver is connected 4 Ensure that all expansion slots on the back or side of the computer are covered Also ensure that all metal retaining brackets are tightly attached to the computer Ai Introduction Thanks you for purchasing our 10 100Mbps Fast Ethernet Adapter This guide is to provide the installation and usag2. Driver for TCP IP software 00C to 55 C Operating 10 to 90 Non condensing FCC Class B CE Mark Microsoft Certified 120 x 40 mm 60 g 1 8W Max Installation 1 Hardware Installation To insert the network adapter into your PC follow the steps bellow 1 Turn off the computer and remove its cover 2 Insert the adapter into a PCI slot 3 Secure this adapter to the rear of the computer chassis and put back the computer cover 4 Connect the adapter to the network using twisted pair cable 2 Hardware Requirement for Wake On LAN If your motherboard support the PCI 2 1 only then the motherboard must provide a 3 pin WOL connector Some computers may require you to change a setting in your computer s BIOS or setup program to enable the WOL feature If the motherboard support PCI 2 2 we don t need the 3 pin WOL connector the function will be provided from the PCI bus directly e ATX 2 01 power supply Note Install only one active WOL adapter per computer You can install additional non WOL adapters 3 Hardware Installation for Wake On LAN If your motherboard support the PCI 2 2 standard no other procedure is needed But you still can follow the steps for PCI 2 1 below on the PCI 2 2 motherboard and all the function include the WOL will work normally If the motherboard support PCI 2 1 only please follow the next procedure 1 Unpack the 3 pin auxiliary powe
3. e of this adapter for network installers and users The 10 100 network adapter complies to PCI 2 1 and PCI 2 2 specification and supports half full duplex feature which can double network speed This adapter supports both 10Mbps and 100Mbps network speed 100BaseTX operates on two pairs of category 5 UTP cable and 10BaseT operates on Category 3 4 5 UTP cable With the Auto Negotiation technology network speed is auto detected When you connect the adapter to 10BaseT hub via UTP cable the network speed becomes 10Mbps Similarly if you connect the adapter to 100BaseTX hub the network speed is 100Mbps If the hub is a switching hub which supports full duplex function then the speed will be doubled to 20Mbps 200Mbps Real hassle free installation is achieved by conforming to PCI bus Just plug in the card and all setup is done automatically No more software to run Furthermore this adapter support the Wake On LAN WOL feature allows users to configure network adapters that are capable of listening to network packets even when the computer is turned off This adapter supplies many drivers including ODI driver for NetWare 3 x 4 x 5 x NDIS driver for Microsoft LAN Manager Windows95 98 NT 2000 Me Linux and a Packet Driver for TCP IP software Whatever your requirements are ease of installation superior performance or responsive support backed up by unlimited technical support this adapter is the superior choice 2 Featu
4. onnected to Wake On LAN E The PC can not boot up after installing the adapter 1 Remove the 3 pin cable from the PC connector 2 Boot up the PC run setup program to configure the adapter as Active Low Default setting is Active High 3 Turn off the PC and reconnect the 3 pin cable to the PC 4 Boot up the PC again E The PC does not boot up when a Magic Packet or Wake Up Frame is sent 1 Check the specification of this PC meets the hardware requirement in chapter 2 2 Verify the BIOS setting of Wake On LAN is configured properly Please check your computer owner s manual or contact your dealer for more information 3 Remove the PC cover and check the 3 pin cable connection 4 Run configure program to check the setting of this adapter 5 If the adapter still does not wake up install a known good working Wake On LAN adapter and 3 pin auxiliary power cable in the PC and recheck the PC Contact your dealer if problem persist TRADEMARKS Copyright 2000 by Edimax Technology Co Ltd No part of this manual may be reproduced transcribed stored in a retrieval system translated into any language or computer language without the prior written consent of Edimax All brand and product names are trademarks and or registered trademarks of their respective companies
5. r cable 2 Insert the 3 pin auxiliary power cable into the connector on the adapter 3 Attach the 3 pin auxiliary power cable to the connector on the PC motherboard 4 Driver Installation Use the drivers supplied by the diskette included in this product For detail description please refer to readme doc or readme exe in the diskette provides by this product 4 Trouble shooting If you experience any problems with the adapter first make sure the appropriate driver is loaded the proper cable is connected to the adapter port and the hub complies with the adapter specification such as 10Mbps 10BaseT or 100Mbps 100BaseTX then check the LED The adapter provides two LEDs to indicate network status m 10M Link Activity A yellow LED indicates if the 10Mbps UTP has been LINK ok or not When the light is OFF it indicates that the 10Mbps UTP port has not been connected or LINK not ok When the light is ON it indicates that the 10Mbps UTP port LINK ok When the light is BLINKING it indicates that there is traffic flow on the network which the adapter is connected to m 100M Link Activity A green LED indicates if the 100Mbps UTP has been LINK ok or not When the light is OFF it indicates that the 100Mbps UTP port has not been connected or LINK not ok When the light is ON it indicates that the 100Mbps UTP port LINK ok When the light is BLINKING it indicates that there is traffic flow on the network which the adapter is c
6. res amp Specifications 1 Features amp Benefits e Supports 32 bit PCI Bus Master for high performance and low processor utilization e Complies to PCI 2 1 and PCI 2 2 specification e Complies with the IEEE 802 3 CSMA CD 100BaseTX and 10BaseT standard e Full duplex design to double the performance to 20Mbps 200Mbps e One STP connector for 100Mbps or 10Mbps network speed e Support Auto negotiation function e Built in FIFO buffers to eliminate external memory e Auto setups IRQ and I O address e Supports early interrupt on transmit to increase performance e Supports ODI driver for NetWare 3 x 4 x 5 x NDIS driver for LAN Manager Windows 95 98 NT 2000 Me Linux and Packet Driver for TCP IP software e Provides diagnostic software and two LEDs to indicate network link activity and 10 100Mbps selection e Supports smart remote Boot ROM 2 Technical Specification e Topology e Connector e Standard e Transmission Rate e Hardware Required e IRQ Line e I O Address e Drivers e Temperature e Humidity e Certification e Dimension e Weight e Power consumption Star RJ 45 IEEE 802 3 10BaseT IEEE 802 3u 100BaseTX L1OMbps or 20Mbps 100Mbps or 200Mbps IBM compatible PC with available PCI slot PCI 2 1 or PCI 2 2 Assigned by system Assigned by system ODI driver for NetWare 3 4 5 NDIS driver for LAN Manager Windows 95 98 NT 2000 Me Linux Packet
Download Pdf Manuals
Related Search