Home
Supermicro Mobile Rack CSE-M28E2
Contents
1. M28E1 and M28E2 MOBILE RACK USER S GUIDE Rev 2 0 SUPERO M28E1 and E2 Mobile Rack User s Guide The information in this User s Manual has been carefully reviewed and is believed to be accurate The vendor assumes no responsibility for any inaccuracies that may be contained in this document makes no commitment to update or to keep current the information in this manual or to notify any person or organization of the updates Please Note For the most up to date version of this manual please see our web site at www supermicro com SUPERMICRO COMPUTER reserves the right to make changes to the product described in this manual at any time and without notice This product including software if any and documentation may not in whole or in part be copied photocopied reproduced translated or reduced to any medium or machine without prior written consent IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN PARTICULAR THE VENDOR SHALL NOT HAVE LIABILITY FOR ANY HARDWARE SOFTWARE OR DATA STORED OR USED WITH THE PRODUCT INCLUDING THE COSTS OF REPAIRING REPLACING INTEGRATING INSTALLING OR RECOVERING SUCH HARDWARE SOFTWARE OR DATA Any disputes arising between manufacturer and customer shall be governed by the l
2. N JP3 Fan Enable 7 a Buzzer Reset O P5 c Figure 3 4 Expander Card E1 Model Rear 3 4 Front Connector and Pin Definitions 1 Backplane Main Power Connectors The 4 pin connectors designated JP1 and JP2 provide power to the backplane See the table on the right for pin definitions 2 Fan Connectors The 3 pin connector designated JP4 pro vides power to the fan See the table on the right for pin definitions 3 10 SAS Ports The SAS ports are used to connect the SAS drive cables The 8 ports are designated 0 7 NOTE Ports 4 5 6 and 7 are avail able on the E2 Models only Safety Information and Technical Specifications Backplane Main Power 4 Pin Connector JP1 and JP2 Pin Definition 1 12V 2 and 3 Ground 4 5V Fan Connector JP4 Pin Definition 1 Ground 2 12V 3 Tachometer SAS Ports Port Information IN and OUT IN and OUT IN and OUT IN and OUT 3 5 SUPERO M28E1 and E2 Mobile Rack User s Guide Jumper Settings hz Te 4 pin PWR Connector SUPER SASEXP M28 REV 1 01A Fan Enable Buzzer Reset 1 P N Buzzer Reset Figure 3 5 Expander Card E2 Model Rear Explanation of Jumpers Connector To modify the operation of the backplane Pins jumpers can be used to choose between optional se
3. v o gt fry J Signal Receptacle 2 84 on NL Ale j ola OO on O IND lp poooooo DUDUDUD 2 adt 0000000 poooooo QoUODUU aooo y Figure 3 1 Mobile Rack Backplane Front Front Connectors and Jumpers 1 Signal Receptacle 2 Power Signal Receptacle 3 Jumper JP25 3 1 SUPERO M28E1 and E2 Mobile Rack User s Guide Explanation of Jumpers To modify the operation of the backplane conector e v jumpers can be used to choose between optional settings Jumpers create shorts between two pins to change the function of the connector Pin 1 is identified with a square solder pad on the printed circuit board Note On two pin jumpers Closed 3 2 1 means the jumper is on and Open means Setting II the jumper is off the pins Jumper Jumper Settings Jumper Jumper Settings Note Open 45 C Overheat Temperature JP25 1 2 50 C 2 3 55 C Backplane Connectors Connector Description J5 P2 Power Signal Receptacle J6 S2 Power Receptacle 3 2 Safety Information and Technical Specifications 3 2 Rear Connectors and LED Indicators N gt Oo N Y oN oon SAS 0 SAS 1 eas hse ERS Ke 4 SAS 5 SAS 6_ SAS 7 J1 J2 J3 J4 J7 J8 J9 J10 WwW Ww gt O O Omo a GO 0000 0000000 FANFAIL OH DRIVE FAIL ania T
4. SAS STOE 3 lod od od od 1 D5 M D11 D15 o x wo o Di DS D2 D6 D324 D7 D4 D8 D9 D13 D107 D144 DIL D15 D124 D167 uus ERI RERI GU O AORE o DG MERA DUTY P D2 D6 D4 D8 D10 D14 D12 D16 Figure 3 2 Mobile Rack Backplane Rear Rear SAS SATA Connectors Rear SAS Drive Connector Number SAS 0 SAS SATA HDD 0 SAS 1 SAS SATA HDD 1 SAS 2 SAS SATA HDD 2 SAS 3 SAS SATA HDD 3 SAS 4 SAS SATA HDD 4 SAS 5 SAS SATA HDD 5 SAS 6 SAS SATA HDD 6 SAS 7 SAS SATA HDD 7 Rear LED Indicators Rear LED Hard Drive Activity Failure LED SAS 0 D5 D1 SAS 1 D6 D2 SAS 2 D7 D3 SAS 3 D8 D4 SAS 4 D18 D9 SAS 5 D14 D10 SAS 6 D15 D11 SAS 7 D16 D12 SUPERO M28E1 and E2 Mobile Rack User s Guide 3 3 Expander Card Front Connectors SUPER SASEXP M28 REV 1 01A pin PWR Connector FANO OO 4 rt f OO gt ri JP HnwN a Fan Enable 1 o Buzzer Reset DIO Figure 3 3 Expander Card E2 Model Rear Front Connectors 1 Power Connectors 4 pin J1 and 6 SAS Port 3 J3 J2 7 SAS Port 4 J11 2 Fan Connector JP4 8 SAS Port 5 J12 3 SAS Port 0 J1 9 SAS Port 6 J13 4 SAS Port 1 J2 10 SAS Port 7 J14 5 SAS Port 2 J4 1O hz NY SUPER SASEXP M28 REV 1 01A og 7 4 pin PWR Connector LU o D Lo E Y Oo
5. aws of Santa Clara County in the State of California USA The State of California County of Santa Clara shall be the exclusive venue for the resolution of any such disputes Supermicro s total liability for all claims will not exceed the price paid for the hardware product Manual Revision 2 0 Release Date August 22 2007 Unless you request and receive written permission from SUPER MICRO COMPUTER you may not copy or otherwise reproduce distribute any part of this document Information in this document is subject to change without notice Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders Copyright 2007 by SUPER MICRO COMPUTER INC All rights reserved Printed in the United States of America Safety Information and Technical Specifications Table of Contents M28E1 and M28E2 MOBILE RACK Contacting Super MICIO coiere t nta hdd dA eps c pr c ec bte C even iv Chapter 1 Safety Guidelines 1 1 ESD Safety Gu idelines n tei aa a aaa Kaaa ESEE 1 1 1 2 General Safety Guidelines cn irte rne textes 1 1 1 39 A Important Note t Users rece paene tva epe caen dnd 1 1 Chapter 2 Introduction 2 1 eT MI E 2 2 Product FEGatUl68 2 2 datio cinere ren bee aere Eni a Fi ra Dose paa Fa sae ko ara Fassa edat ea dira d Additional Information Chapter 3 Jumper Setting and Pin Defi
6. icro Headquarters Address SuperMicro Computer Inc 980 Rock Ave San Jose CA 95131 U S A Tel 1 408 503 8000 Fax 1 408 503 8008 Email marketing supermicro com General Information support supermicro com Technical Support Web Site www supermicro com Europe Address SuperMicro Computer B V Het Sterrenbeeld 28 5215 ML s Hertogenbosch The Netherlands Tel 31 0 73 6400390 Fax 31 0 73 6416525 Email sales supermicro nl General Information support supermicro nl Technical Support rma supermicro nl Customer Support Asia Pacific Address SuperMicro Taiwan 4F No 232 1 Liancheng Rd Chung Ho 235 Taipei County Taiwan R O C Tel 886 2 8226 3990 Fax 886 2 8226 3991 Web Site www supermicro com tw Technical Support Email support supermicro com tw Tel 886 2 8228 1366 ext 132 or 139 Safety Information and Technical Specifications Chapter 1 Safety Guidelines To avoid personal injury and property damage carefully follow all the safety steps listed below when accessing your system or handling the components 1 1 ESD Safety Guidelines Electric Static Discharge ESD can damage electronic components To prevent dam age to your system it is important to handle it very carefully The following measures are generally sufficient to protect your equipment from ESD 1 3 Use a grounded wrist strap designed to prevent static discharge Touch a grounded metal object before removing a comp
7. nitions 3 1 Front Gonnectors and J mbpets erect naa anaE 3 1 Front Connectors and Jummp6ts ciem eee eee ves 3 1 Explanation Of JUMPE Siroes sienien e tg caedes ie ree ER Deio Rre AREG h 3 2 3 2 Rear Connectors and LED Indicators orae ce eint re ie 3 3 9 9 Expander Gard to its dde cades rec eara Hdcex dux Front Connectors FROMECOMME CIOS correo residere aee EO E OE IUE keen 3 4 Front Connector and Pin Definitions 2 e crest enge 3 5 Nec 3 6 Explanation of Jumpers 5 ennt ke et eb eee eec bred 3 6 Chapter 4 Installation Instructions 4 1 SHIPPING List ise cece 4 1 4 2 TOOS REGUE Device aca HE eee rae e eee creed are 4 1 4 3 Other IP AMS atc ire rre tree ree qe se toset epe quechsaet EEUE EEEO EEEE Pe KERN IRR MERE 4 1 4 4 Setup and Installation Steps 2 boni te ee techos 4 2 4 5 X General Safety Guidelines eiiis cepe tenen inan 4 6 Before Accessing the Mobile Rack 4 7 Cooling Fan Installation sessessssesseeeeeeneeeeee nnne Fari Removal rtr iere t e reae d IE Eg 4 8 Hard Drive InstallatiOn uoce or eee tre rt e DR ordnen exert 4 9 Connect Data and Power Cables neither eni rennen 4210 Advanced Configuratio eiui perenne retrum meteor aep pera o Yo opes eH Meus SUPERO M28E1 and E2 Mobile Rack User s Guide Contacting Super M
8. onent from the antistatic bag Handle the RAID card by its edges only do not touch its components peripheral chips memory modules or gold contacts When handling chips or modules avoid touching their pins Put the card and peripherals back into their antistatic bags when not in use General Safety Guidelines Always disconnect power cables before installing or removing any components from the computer including the backplane Disconnect the power cable before installing or removing any cables from the backplane Make sure that the backplane is securely and properly installed on the motherboard to prevent damage to the system due to power shortage An Important Note to Users All images and layouts shown in this user s guide are based upon the latest PCB Revision available at the time of publishing The card you have received may or may not look exactly the same as the graphics shown in this manual 1 1 SUPERO M28E1 and E2 Mobile Rack User s Guide Notes 1 2 Safety Information and Technical Specifications Chapter 2 Introduction 2 1 Overview This manual is written for system integrators PC technicians and knowledgeable PC users It provides detailed information for the installation and use of the M28E1 M28E2 Mobile Rack The Supermicro M28E1 M28E2 Mobile Rack showcases advanced technology innovations in modular connectivity and data transferability and supplies reliable effective and scalable soluti
9. ons for tomorrow s data communications industry 2 2 Product Features The M28E1 M28E2 Mobile Rack provides the following Slim design pocket size 5 5 W x 2 5 H Two LSI SAS X12 Expanders built in for the M28E2 and One LSI SAS X12 Expander for the M28E1 Supports 8 x 2 5 SFF HDD Supports up to 5V 10A Average and 12V 10A Average Provides up to 3 Gbps transfer speed Supports SAS SATA II with potential support of up to 144 SAS devices Operating Systems This mobile rack supports the following Operating Systems Windows 2000 Windows XP and Windows 2003 Linux Red Hat and SuSE 2 1 SUPERO M28E1 and E2 Mobile Rack User s Guide Additional Information The M28E1 M28E2 Mobile Rack was designed for use in certain chassis and Servers or as a stand alone unit Use the chassis or server manual for installa tion instructions Use the instructions listed in this manual to use the mobile rack independent of a chassis The pictures or graphics shown in this User s Guide were based upon the latest PCB revision available at the time of the publishing of this manual The M28E1 M28E2 Mobile Rack may or may not look exactly the same as the graphics shown in this manual The availability of SAS devices supported depends on the readiness of firmware and hardware support 2 2 Safety Information and Technical Specifications Chapter 3 Jumper Setting and Pin Definitions 3 1 Front Connectors and Jumpers
10. rives to the rear of the hard drive tray Secure the hard drive to the tray using four M3 screws as illustrated Using the hard drive tray latch as a handle slide the hard drive into the mobile rack Close the hard drive tray handle to lock the hard drive into place Repeat steps 1 8 for each hard drive that you will install into the mobile rack 4 5 SUPERO M28E1 and E2 Mobile Rack User s Guide 4 9 Connect Data and Power Cables Use the following instructions to complete setup of your mobile rack 1 Connect the SAS cables to the mobile rack A longer SAS cable may be required see the recommended cables listed earlier in this manual 2 Connect the power cables from the chassis power supply A power cable extension may be required 4 10 Advanced Configuration Use the following instructions in the unlikely event that you must access the jump ers buzzer or other backplane components Mobile Rack Casing Remove these screws Figure 4 4 Mobile Rack and Rear Casing To access the mobile rack backplane optional 1 Remove the two screws that secure the casing to the mobile rack 2 Slide the casing downward and remove it from the mobile rack
11. structions in the chassis manual 4 5 4 6 1 Unpack and examine system parts 2 Review all system and safety guidelines 3 Install the system fan 4 Install the hard drives 5 Connect data and power cables General Safety Guidelines Always disconnect power cables before installing or removing any compo nents from the computer including the backplane Disconnect the power cable before installing or removing any cables from the mobile rack or backplane Make sure that the backplane is securely and properly installed on the motherboard to prevent damage to the system due to power shortage Before Accessing the Mobile Rack Power down and power supply connected to the chassis or server In addi tion unplug all power cords from the wall outlet Disconnect all necessary cables and label the cables for easy identification Use a grounded wrist strap designed to prevent static discharge when han dling components Save all screws and fasteners for later use Familiarize yourself with and follow the instructions in this section 4 2 Safety Information and Technical Specifications 4 7 Cooling Fan Installation When using the M28E1 or M28E2 without installing the mobile rack in a larger unit such as a chassis you must install a cooling fan For more information on installing the mobile rack into a chassis or server see the documentation for your mobile rack or server You can also visit our website a
12. t http www supermicro com Release Tabs Fan Connector Tab Openings Figure 4 1 Mobile Rack with Fan Use the following instructions to install the cooling fan 1 Press the release tabs on both sides of the cooling fans as shown 2 Attach the fans to the mobile rack by sliding the release tabs into the open ings until the fan clicks into place 3 Attach the cooling fan cable to the Fan Connector 4 3 SUPERO M28E1 and E2 Mobile Rack User s Guide Fan Removal Use the following instructions to remove the cooling fan from the mobile rack 1 Remove the fan cable from the mobile rack by gently but firmly pulling the cable from the backplane 2 Press both release tabs and pull the fan from the mobile rack 4 8 Hard Drive Installation Each M28 Mobile Rack includes dummy trays that act as place holders for hard drives Before using the mobile rack you must install hard drives to the trays Hard drives are sold separately Hard Drive Tray Latch Release Tab Figure 4 2 Mobile Rack with Hard Drive Trays To install hard drives into the mobile rack 1 Press the release tabs to open the hard drive tray latch 2 Using the latch as a handle pull the tray from the hard drive Safety Information and Technical Specifications Hard Drive M3 Screws Figure 4 3 Hard Drive and Hard Drive Tray Place a 2 5 hard drive in the hard drive tray Align the hard d
13. ttings Jumpers create shorts between two pins to change the function of the connector Pin 1 is identified with a square solder pad on the printed circuit board Note On two pin jumpers Closed Jumper means the jumper is on and Open means Setting the jumper is off the pins Jumper Settings Jumper J3 J5 Jumper Settings Closed With Fan Open No Fan Open Enabled Closed Disabled Note Fan Enable Buzzer Reset Safety Information and Technical Specifications Chapter 4 Installation Instructions 4 1 Shipping List Examine the your order for the following parts M28E1 M28E2 Mobile Rack One 80mm Cooling Fan Fan 0084 e 32 M3 screws Four Round head screws SATA 4 lane cable 4 2 Tools Required M28E series Mobile Rack assembly requires the following Phillips head screwdriver Industry standard anti static strap recommended 4 3 Other Parts When using this mobile rack independent of a chassis you may need the follow ing parts 4 pin Power cord extension to connect the mobile rack to a power sup ply SAS iPass cable part number CBL 0116 used to connect the SAS ports to the motherboard or add on card 4 1 SUPERO M28E1 and E2 Mobile Rack User s Guide 4 4 Setup and Installation Steps Use the following list as a guide to setup and install the mobile rack If this mobile rack is to be installed in a chassis use the in
Download Pdf Manuals
Related Search
Related Contents
Caratteristiche del tablet Pluviomètre ARG100 - Campbell Scientific Nokia C6-01 User Guide Logic fun User Guide American Standard Cadet 3305.000 User's Manual manualeinstallazione-uso_motoritapparelle-tendedasole B64-3454-00_French r3.Indd MR. C@+-EE@ :OdeL”`t Copyright © All rights reserved.
Failed to retrieve file