Benq MP610
Contents
1. PIPE BASE M4 SCREW x 3 PROJECTOR ADAPTER Packing Parts List 3 projector Installation and Throw Distance Chart Floor Installation for a 4 3 screen Maximum zoom Minimum zoom Screen Center of lens Vertical Offset I Projection distance Screen Size Diagonal Distance from Screen in mm Vertical Offset in mm Feet Inches mm Minlength Average Max length with max with min zoom zoom 1876 2199 2345 2815 3078 3284 3753 3848 4222 4617 4691 5387 5629 6157 7036 7695 8444 9234 11727 Ci The recommended focus range is from 1500 8000 millimeters 1 5 8 meters There is 3 5 tolerance among these numbers due to optical component variations 4 Projector Installation and Throw Distance Chart installing a Projector with The Ceiling Bracket Overview M Diagram of completed installation M Ceiling Mount Device Installation Procedure STEP A Insert the U PLATE into the CEILING ADAPTER and tighten two M4 screws from the bottom into the screw holes Then attach the top part to the ceiling U PLATE CEILING ADAPTER 8 MA screws 3 Ceiling mount screws not included Installing a Projector with the Ceiling Bracket 5 NUTSx2 STEP D Install the base assembly 6 AP T C P STEP D1 Attach the PIPE BASE to the H ADJUST ADAPTER with 2 MA screws MA screw 7 H ADJUST AD2. APTER PIPE BASE Installing a Projector with the Ceiling Bracket AE STEP B Install the TUBE and the U PLATE with 2 sets of bolts amp nuts TUBE BOLT TUBE BOLTS x 2 TUBE is STEP C Install the PIPE and the TUBE with 2 sets of bolts amp nuts L ADJUST BOLT N NUTSx2 e XO us L ADJUST BOLTS x2 PIPE O U O STEP D2 Assemble the PROJECTOR ADAPTER and the projector with 3 M4 screws M4 screw PROJECTOR ADAPTER 0 STEP E Combine the H ADJUST ADAPTER including the PIPE BASE and the PROJECTOR ADAPTER with one V ADJUST BOLT set bolt washer and nut Then tighten the M4 screws on both sides H ADJUST ADAPTER Assemble BASE ASSEMBLY and the ceiling mount device with 2 sets of bolts and nuts PIPE BOLT STEP F sets Two people are required for the completion of this step Ceiling mount bracket NUT PIPE BOLT BASE ASSEMBLY Installation finished Installing a Projector with the Ceiling Bracket 7 adjusting the Ceiling Bracket Height Adjustment I Make sure to remove the projector first Loosen the nuts securing to the two L ADJUST BOLTS Remove the L ADJUST BOLTS from the PIPE Adjust to the correct position for the height of the screen The height can be BY gt adjusted to 218mm or any value in a range between 548mm and 758mm in increments of 30 mm 5 Insert the L ADJUST BOLT back into the PIPE and t
3. BenQ MP610 MP720 MP770 Ceiling Mounting Guide Welcome Copyright Copyright 2005 by BenQ Corporation All rights reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without the prior written permission of this company Disclaimer BenQ Corporation makes no representations or warranties either expressed or implied with respect to the contents hereof and specifically disclaims any warranties merchantability or fitness for any particular purpose Further BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of this company to notify any person of such revision or changes Safety Instructions 1 Follow the instructions in this guide when installing the projector with this bracket Improper or inadequate installation could cause the projector to fall and cause injures Make sure the installation is secure enough to bear the weight of all and withstand vibrations Use only the parts provided with the bracket and any parts commercially available that are specified in this guide Do not modify the bracket or the parts provided with the bracket Do not use damaged parts If any parts become damaged contact your dealer All bol
4. hen re attach the nuts previously removed Maximum Height Minimum Height 8 Adjusting the Ceiling Bracket Horizontal Angle Adjustment l Loosen the two sets of screws connecting the PIPE BASE and the H ADJUST ADAPTER 2 Adjust the horizontal angle so that it is correct for the orientation of the screen 3 Re tighten the two sets of screws connecting the PIPE BASE and the H ADJUST ADAPTER 4 The swivel angle can be set within a range of negative to positive 30 degrees 30 Vertical Angle Adjustment 1 Loosen the two sets of screws connecting the H ADJUST ADAPTER and the PROJECTOR ADAPTER 2 Adjust the vertical angle to the correct one for the orientation of the screen 3 Re tighten the 2 sets of screws connecting the H ADJUST ADAPTER and the PROJECTOR ADAPTER 4 The tilt angle can be adjusted in a range between 5 and 15 degrees Adjusting the Ceiling Bracket 9 E specifications and Diagrams Specifications Adjustment Range Height 218mm 548mm 578mm 608mm 638mm 668mm 698mm 728mm and 758mm Horizontal angle 30 to 30 degrees Vertical angle 5 to 15 degrees Diagrams B Left View Bb Front view 10 Specifications and Diagrams
5. ts and screws must be tightened securely Make sure not to block any ventilation openings when installing the projector Do not install the projector in a location that is subject to high levels of dust or humidity E a oe Ugo i e Do not install the projector in a location that is exposed to direct sunlight or in a location that is subject to extreme fluctuations in temperature such as near an air conditioner 10 Clean only with a dry cloth 11 Special techniques and experience are required when installing the projector with this bracket It is recommended that you contact your dealer to install the projector for you 12 Once the projector is installed safety checks should be conducted on a regular basis Table of Contents hcic a 3 Projector Installation and Throw Distance Birne ee een 4 Vis talline 4 Projector wih The Ceiling Drache ee een E EARE R 5 O a AE E C EE E ee A E E E E E sss 8 SE e and Da ea 10 2 Copyright Packing Parts List CEILING ADAPTER U PLATE TUBE PIPE PIPE BASE H ADJUST ADAPTER PROJECTOR ADAPTER V ADJUST BOLT NUT x7 WASHER x 1 MA SCREW x 10 BOIT x 6 TUBE BOIT x 2 L ADJUST BOLT x 2 PIPE BOLT x 2 Names of Parts U PLATE CEILING ADAPTER M4 SCREW x 2 TUBE TUBE BOIT x 2 L ADJUST BOLT x 2 PIPE PIPE BOLT x 2 M4 SCREW x 4 4L m H ADJUST ADAPTER V ADJUST BOLT
Download Pdf Manuals
Related Search