Home

Hitachi Ultrastar 10K300-73GB

1. Technologies Hitachi Global Storage Technologies 5600 Cottle Road San Jose CA 95193 Produced in the United States 8 04 All rights reserved DeskstarTM is a trademark of Hitachi Global Storage Technologies Microsoft Windows XP and Windows are trademarks of Microsoft Corporation in the United States other countries or both Other product names are trademarks or registered trademarks of their respective companies References in this publication to Hitachi Global Storage Technologies products programs or services do not imply that Hitachi Global Storage Technologies intends to make these available in all countries in which Hitachi Global Storage Technologies operates Product information is provided for information purposes only and does not constitute a warranty Information is true as of the date of publication and is subject to change Actual results may vary This publication is for general guidance only Photographs may show design models 17 August 2004 version 1 1
2. current limiter and Schottky diode This function can be selected by jumper 80 pin SCA 2 models do not support SCSI bus Terminator Power Vibration and shock Operating vibration The overall RMS root mean square vibration level on all axis is 1 0 G Non operating vibration The overall RMS level of vibration level on all axix is 5 0 G Operating shock The drive withstands with no data loss a half sine shock pulse of 15 G of 11 ms duration The shock pulses are applied ten pulses for each direction and for all three axes for a total of 60 pulses There must be a minimum delay of 30 seconds between shock pulses to allow the drive to complete all ne cessary error recovery procedures Non operating shock The drive withstands with no data loss a half sine shock pulse of 75 G of 11 ms duration and a half sine shock pulse of 250 G of 2 ms duration The shocks are applied in each direction of the three mutually perpendicular axes of the drive Rotational shock The drive withstands with no data loss a rotational shock of 30 000 rad s applied around the axis of the actuator pivot for a duration of 1 ms Page 4 Operating environment The drive operates within its perfor mance limits when the following environmental conditions are main tained Operating conditions Temperature 5 55 C Relative humidity and non condensing ear Max wet bulb temp non condensing ae Max temp gradie
3. Product Summary Hitachi Ultrastar 1OK300 Ultra 320 SCSI hard disk drive HUS103030FL3600 HUS103014FL3600 HUS103073FL3600 HUS103030FL3800 HUS103014FL3800 HUS103073FL3800 Models Introduction The new Hitachi Ultrastar 10K300 offers capacities of 300 GB 147 GB and 73 GB in Ultra 320 SCSI models The high reliability and excellent performance of the Hitachi Ultrastar 10K300 are the result of the implemen tation of a number of advanced disk drive technologies including giant magnetoresistive head technology No ID sector formatting Predictive Failure Analysis and ECC on the fly correction Applications Technical commercial workstations e Network servers e High end personal computers e CAD CAM e Multimedia e Transaction processing e Data mining applications Features Benefits e Capacities of 300 GB 147 GB 73 GB e 68 and 80 pin Ultra 320 industry standard interface e Wide range of capacities e Interface data rates of 320 MB s e Shock Nonoperational 250 G 2ms 75 G 11 ms Operational 15 G 11 ms e Robust design for portable computing applications e Rotational speed 10 000 RPM e Excellent data rate across disk surface e Average seek time Read 300GB 4 7 ms 147GB 4 5 ms 73 GB e Average latency 2 99 ms e Areal density 61 Gbits square inch e Fast access to data e Increased storage capacity e No ID sector formatting e PRML data cha
4. UNIT command is received Disable Auto Spin Up 80 pin models If pins 1 amp 2 position Q on 80 pin models are not jumpered the drive will spin up automatically after a power on reset Installing a jumper on this position prevents the drive from spinning up unless a START UNIT command is received Auto Start Delay Delay Start 6 12 Installing a jumper on pins 3 amp 4 position P and 5 amp 6 position O controls when and how the drive spins up in conjunction with pins 1 amp 2 When both Auto Spin Up and Auto Start Delay are enabled the drive start is delayed by a period of time multiplied by the SCSI address of the drive If Auto Spin Up is disabled these jumpers will be ignored Disable SCSI Parity Check Installing a jumper on pins 7 amp 8 position N disables SCSI Parity checking Enable TI SDTR Installing a jumper on pins 9 amp 10 position M enables Target Initiated Synchronous Data Transfer Request Negotiation Disable Unit Attention Installing a jumper on pins 11 amp 12 position L enables control of the Unit Attention Inhibit UAI bit in Mode Page 0 Data organization logical Model Heads Disks 300 GB 12 5 147 GB 5 3 73 GB 3 2 Seek times typical ms GB ms Average 300 GB 4 7 Page 3 Read 147 GB 4 5 73 GB 4 2 Full stroke Read 10 Full stroke Write 11 DC power requirements The following voltage specifications apply at the drive powe
5. ace is capable of accepting commands Spindle mo tor is stopped All circuitry except host interface is in power saving mode The execution of commands is delayed until spindle becomes ready Page 5 Electromagnetic compatibility When installed in a suitable enclo sure and exercised with a random accessing routine at the maximum data rate the drive meets the following worldwide EMC require ments United States Federal Communications Commission FCC Rules and Regulations Class B Part 15 This drive is certified for compliance to EC directive 89 336 EEC C Tick Mark complies with Australian EMC standard AS NZS 3548 1995 Class B The drive complies with Taiwan BSMI EMC standard Physical dimensions Height mm 26 1 Width mm 101 6 0 25 Length mm 147 0 0 6 Weight grams max 75 Refer to the illustration below Mounting The drive will operate in all axes six directions To avoid perfor mance degradation the drive must be mounted securely in the system Drive level vibration tests and shock tests are to be conducted with the drive mounted to the table using the bottom four screws Refer to the illustration on the next page for mounting positions and tappings version 1 1 Hitachi Global Storage Technologies Mounting and Mechanical dimensions Page 6 version 1 1 Hitachi Global Storage Technologies Page 7 Copyright Hitachi Global Storage
6. ccord ance with IS07779 Drives must meet these criteria in both board up and board down orientations A weighted sound power levels Idle Typical Bels 3 4 The acoustical characteristics of the drive subsystem are measured under the following conditions Idle mode powered on disks spinning track following unit ready to receive and respond to control line commands Operating mode continuous random cylinder selection and seek operation of the actuator with a dwell time at each cylinder The seek rate Ns is to be calculated according to the following formula Ns 0 4 Tt T1 where Ns avg seeks per second Tt published random seek time and T1 time for the drive to rotate by half a revolution version 1 1 Hitachi Global Storage Technologies Operating modes To provide the greatest flexibility of operation with optimum perfor mance and power consumption the drive has a number of operating modes These are defined below Spin Up Start up time period from spindle stop or power down Seek Seek operation mode Write Write operation mode Read Read operation mode Performance idle The device is capable of respond ing immediately to media access re quests All electronic components remain powered and full frequency servo remains operational Low Power idle Spindle motor is rotating normally with actuator unloaded to the park ing positions Standby The device interf
7. ess 12 I T 5 Address 5 T T H Address 13 a I i a Address 6 a I H i Address 14 i I I n Address 7 i l i l Address 15 The drive has two option jumper blocks designated as J 4 and J 6 located on the circuit board J 4 Jumper settings SCSI ID address settings Assign a SCSI address by placing jumpers on the appropriate address pins D E F and G Refer to address settings in the illustration above LED pins The LED pins are used to drive an external Light Emit ting Diode Up to 30 mA of sink current is provided Refer to the Ultrastar 146Z10 Hard Disk Drive Specifi cations for a detailed functional description of this pin Termination Power If a jumper is installed on pins 3 amp 4 position I of the 68 pin models termination power is supplied to pins 17 18 51 and 52 of the 68 pin SCSI interface Force SE Mode Installing a jumper on pins 5 amp 6 position H causes the drive to function in single ended mode version 1 1 Hitachi Global Storage Technologies J 6 Jumper settings Enable Auto Spin Up 68 pin models Installing a jumper on pins 1 amp 2 position Q on 68 pin models causes the drive to spin up automa tically after a power on reset If this position is not jumpered the drive will not spin up unless a START
8. lug events the non operational shock levels should not be exceeded The operational shock levels of adjacent drives should also not be exceeded The recommended procedure is to prohibit write operations to adjacent drives during Hot Plug and Hot Unplug actions During Hot Unplug the operational shock limit specifications should not be exceeded If this cannot be guar anteed the drive should be issued a SCSI Stop Unit command that is allowed to complete before unplug ging The basic requirement is that the operational shock limits are in effect while the drive is operational or spinning down Once the drive has completely stopped the nonoperational shock limits are in effect The recommended procedure is to allow the unplugged drive to rest in the drive bay for a minimum of 15 seconds and then complete the removal During Hot Plug or Unplug events the power supply ripple on adjacent operational drives should not be outside the 5 regulation tolerance SCSI bus connectors and cable Refer to ANSI SCSI Parallel Inter face 3 T10 1302D revision 11 for detailed specifications version 1 1 Hitachi Global Storage Technologies SCSI bus terminators optional On board SCSI active termination is not supported The using system is responsible for making sure that all required signals are terminated at both ends of the bus cable Terminator power Terminator power can be provided by the 5V power supply through
9. nnel e More data stored per track increased sustained data transfer rate e 8 MB SCSI buffer for read and write e On The Fly correction e Fast access to data and improved throughput e High reliability e Load Unload heads e Increased durability during power save modes and non operation e Predictive Failure Analysis e High reliability and availability e Giant Magnetoresistive heads e _No ID sector formatting e High areal density low component count e Adaptive power save control e Low power for battery powered applications Page 1 version 1 1 Hitachi Global Storage Technologies Electrical connectors Pin 1 80 pin SCA models rear view Uses a DDK connector which is compatible with SCSI Parallel Interface 3 SPI 3 68 Pin SCSI Connector Auxiliary Connector SCSI Pin 1 Power Pins y U es 68 pin models rear view Complies with the ANSI SCSI P connector specifi cations Pin Voltage 1 12 V 2 GND 3 GND 4 5V Reserved Ground LED Cathode Auxiliary block of 68 pin models Page 2 Option jumper blocks i a p Address 0 sl a a J Address 8 7 g g g Address 1 i a al H Address 9 T a a Address 2 a i gt i Address 10 I I B p Address 3 T H El H Address 11 A i a Address 4 a p i i Addr
10. nt 15 C hour Altitude meters 300 to 3048 Non operating conditions Temperature 40 to 70 C Relative humidity Ane non condensing ae sO Max wet bulb temp non condensing 29 C hour Max temp gradient 15 C hour Altitude meters 300 to12 000 NOTE The system must provide sufficient ventilation to maintain a surface temperature not to exceed 60 C at the center of the top cover of the drive Non condensing con ditions should be kept at all times Maximum storage period in the shipping package is one year Corrosion test The hard disk drive shows no signs of corrosion inside or outside of the hard disk assembly and is function al after subjection to a temperature of 50 C with a relative humidity of 90 for seven days ATTENTION The drive must be protected against electrostatic dis charge ESD especially when being handled The safest way to avoid damage is to put the drive in an anti static bag before ESD wrist straps are removed Drives must be shipped in approved containers Severe damage can be caused to the drive if the packaging does not adequately protect against the shock levels induced when a box is dropped Consult your Hitachi representative if you do not have an approved shipping container Acoustics The criteria of the A weighted sound power levels are given in Bel relative to one pico watt and are shown in the following table The measurement method is in a
11. r connector Connection to the drive should be made in safety extra low voltage SELV circuits No special power on off sequencing is required 5V 5 12V 5 5 volt supply 12 volt supply A deviation up to 8 is acceptable during drive spin up however spin up time is not guaranteed Power supply current 5V pop mean in Amps Idle average 0 60 Start up Maximum 70 12V pop mean in Amps 300 GB_ 147 GB Idle avg 0 68 0 46 Seek peak 2 52 2 32 Start upmax 2 45 2 45 73 GB Idle avg 0 42 Seek avg 2 15 Start upmax 2 28 Generated ripple at drive power connector During drive start up and seeking 12 volt ripple is generated by the drive referred to as dynamic load ing If the power of several drives is daisy chained together the power supply ripple as well as the dynamic loading of other drives must remain within the regulation tolerance of 5 A more desirable method of power distribution is a common supply with separate power leads to each drive Hot Plug Unplug support The term Hot Plug refers to the action of mechanically engaging a device to the power and or bus when other devices may be active on the same bus While every effort was made to design the drive not to influence the SCSI bus during these events it is the responsibility of the system to insure voltage regulation and con formance to operational and non operational shock limits During Hot P

Hitachi Ultrastar 10K300-73GB

Contents

Download Pdf Manuals

Related Search

Related Contents