APC SmartSlot Tripple Chassis 19" +3sl
Contents
1. Chassis using the holes provided Choose a position that will not cause the mounted Triple Chassis or the attached cables to interfere with closing the cabinet door or to otherwise protrude from the cabinet If more than two mounting holes are aligned choose the pair that are farthest apart 3 Mount the Triple Chassis into the NetShelter enclosure with 4 caged nuts and machine screws not supplied If the Triple Chassis is being installed in a enclosure other than a NetShelter use the hardware that is appropriate for the enclosure 4 Connect the female end of the included cable to the 9 pin male connector labeled To UPS on the front of the Triple Chassis 5 Connect the male end of the cable to the 9 pin female computer interface port on the rear of the UPS 6 If UPS monitoring is to be used connect the required cable 940 0024 not supplied from the 9 pin monitoring port on the front of the Triple Chassis to an appropriate serial port on a computer or to another card 7 If additional power is needed see Power Consider ations on page 5 connect the optional power adapter output to the power port on the front of the Triple Chassis Installation Power Considerations Optional power adapter The power required for the operation of the card is normally provided to the Triple Chassis by the UPS There is a limit to the amount of power available and the total power required by allthe car2. specific centers go to www apc com support contact for contact information Contact the APC representative or other distributor from whom you purchased your APC product for information on how to obtain local customer support Entire contents copyright O 2002 American Power Conversion All rights reserved Reproduction in whole or in part without permission is prohibited APC Share UPS Matrix UPS NetShelter and the APC logo are trademarks of American Power Conversion Corporation and may be registered in some jurisdictions All other trademarks product names and corporate names are the property of their respective owners and are used for informational purposes only 990 0145C 01 2002
3. 0024 verified Warranty and Service Limited warranty Warranty limitations APC warrants the Triple Expansion Chassis to be free from defects in materials and workmanship for a period of two years from the date of purchase Its obligation under this warranty is limited to repairing or replacing at its own sole option any such defective products This warranty does not apply to equipment that has been damaged by accident negligence or misapplication or has been altered or modified in any way This warranty applies only to the original purchaser Except as provided herein APC makes no warranties express or implied including warranties of merchantability and fitness for a particular purpose Some jurisdictions do not permit limitation or exclusion of implied warranties therefore the aforesaid limitation s or exclusion s may not apply to the purchaser Except as provided above in no event will APC be liable for direct indirect special incidental or consequential damages arising out of the use of this product even if advised of the possibility of such damage Specifically APC is not liable for any costs such as lost profits or revenue loss of equipment loss of use of equipment loss of software loss of data costs of substitutes claims by third parties or otherwise This warranty gives you specific legal rights and you may also have other rights which vary according to jurisdiction Warranty and Service O
4. Triple Expansion Chassis AP9604 Installation Manual Contents Introduction Installation Power Considerations Operations Specifications Warranty and Service Life Support Policy Introduction The APC Triple Expansion Chassis is a 3 slot chassis designed to accommodate APC management cards The Triple Chassis allows you to e Use cards with APC UPSs that are not equipped with a card slot but do have an advanced Computer Interface Port e Add cards to UPSs that have an existing card slot e Use cards such as the Environmental Monitoring Card in a stand alone configuration Hardware e Three card slots e 9 pin male port for connecting the Triple Chassis to the computer interface port of the UPS e Power input connector for optional power adapter e 9 pin female UPS monitoring port that duplicates the functions of the computer interface port on the UPS e Status indicator LED e Mounting enclosure hardware Introduction 1 Installation Configurations Desktop installation The Triple Chassis can connect to any APC device equipped with an advanced type computer interface port This includes certain Smart UPS and Matrix UPS products and any other management card that duplicates the functions of the UPSs computer interface port such as the Share UPS e Stand alone desktop unit e Mounted in a NetShelter EIA 310 D 19 inch enclosure The Triple Chassis is equipped
5. at a the risks of injury or damage have been minimized b the customer assumes all such risks and c the liability of American Power Conversion is adequately protected under the circumstances The term ife support device includes but is not limited to neonatal oxygen analyzers nerve stimulators whether used for anesthesia pain relief or other purposes autotransfusion devices blood pumps defibrillators arrhythmia detectors and alarms pacemakers hemodialysis systems peritoneal dialysis systems neonatal ventilator incubators ventilators for adults and infants anesthesia ventilators infusion pumps and any other devices designated as critical by the U S FDA Hospital grade wiring devices and leakage current protection may be ordered as options on many APC UPS systems APC does not claim that units with this modifications are certified or listed as hospital grade by APC or any other organization Therefore these units do not meet the requirements for use in direct patient care Life Support Policy Radio Frequency Interference Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate this Warning equipment This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interfere
6. btaining To obtain support for problems with your Triple Expansion service Chassis 1 2 Warranty and Service Note the serial number and date of purchase Contact Customer Support at a phone number on the back cover of this document A technician will try to help you solve the problem by phone If you must return the product the technician will give you a return material authorization RMA number If the warranty expired you will be charged for repair or replacement Pack the unit carefully The warranty does not cover damage sustained in transit Enclose a letter with your name address RMA number and daytime phone num ber a copy of the sales receipt and a check as payment if applicable Mark the RMA number clearly on the outside of the shipping carton Ship by insured prepaid carrier to the address provided by the Customer Support technician Life Support Policy General policy Examples of life support devices 10 American Power Conversion APC does not recommend the use of any of its products in the following situations e In life support applications where failure or malfunction of the APC product can be reasonably expected to cause failure of the life support device or to affect significantly its safety or effectiveness e Indirect patient care APC will not knowingly sell its products for use in such applications unless it receives in writing assurances satisfactory to APC th
7. ds installed in the Triple Chassis must not exceed this limit If this limit is exceeded it is likely that the management product will cease to operate properly The limits are e Smart UPS 200 mA e Matrix UPS 200 mA To determine the total amount of power required add the individual power requirements for each of the management products to be installed in the Triple Chassis as well as the power requirements for the Triple Chassis itself The power requirements for each individual card can be obtained from the documentation included with that card In cases where the power requirements exceed 200 mA APC s optional 24VDC AP9505 not supplied adapter may be used to supplement the UPS power by providing an additional 400 mA The power adapter is also required under the following conditions e Smart UPS models Serial number prior to 9405 Serial number starting with the letter W All Smart UPS 250 models e Matrix UPS models When remote turn on of the UPS is required The optional power adapter is used with 100 120 VAC power only AP950SI is also available for universal power input but requires a customer supplied line cord If you need to obtain a power adapter contact APC Customer Service at a telephone number on the back cover Power Considerations 5 Operations Status indicator The Triple Chassis status LED indicates the following states State Indication Brisht The Triple C
8. hassis has power and at 8 least one management card is installed The Triple Chassis has power and no Dim ree management card is installed Off The Triple Chassis has no power Checking 1 After installing the Triple Chassis and before installing operation the card confirm that the indicator light is dimly lit 2 After installation of the card confirm that the indicator light is brightly lit 3 Confirm the operation of the card Refer to the documentation that was included with the card for the proper checking procedure 4 Confirm that previous installed cards and software continue to operate 6 Operations Specifications Item Specification Electrical Operating voltage 18 30 V Operating current draw 30 mA exclusive of installed card Physical Size H x W x D For desktop installation with rubber feet 2 13 x 17x 6 5 in 5 4 x 43 18 x 16 51 cm For rack mount installation with mounting brackets 1 75 x 17 x 6 5 in 4 4 x 43 18 x 16 51 cm Weight 1 5 1b 0 7 kg Shipping weight 2 Ib 0 9 kg Environmental Operating elevation storage 0 to 1000 ft 0 to 50 000 ft 0 to 3000 m 0 to 15 000 m Operating temperature storage 5 to 45 C 25 to 65 C 23 to 113 F 13 to 149 F Approvals EMC verification FCC Class A DoC Class A EN55022 Class A VCCI AS NZS 3548 Electromagnetic immunity Specifications EN5
9. nce when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and 1f not installed and used in accordance with this user manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference The user will bear sole responsibility for correcting such interference This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme a la norme NMB 003 du Canada www apc com APC Worldwide Customer Support Customer support for this or any other APC product is available at no charge in any of the following ways e Visit the APC Web site to find answers to frequently asked questions FAQs to access documents in the APC Knowledge Base and to submit customer support requests www apc com Corporate Headquarters Connect to localized APC Web sites for specific countries each of which provides customer support information www apc com support Global support with FAQs knowledge base and e support e Contact an APC Customer Support center by telephone or e mail Regional centers APC Headquarters U S amp Canada 1 800 800 4272 toll free Latin America 1 401 789 5735 USA Europe Middle East Africa 353 91 702020 Ireland Japan 03 5434 2021 Guidance 3 Local country
10. with rubber feet for desktop use and can be set up wherever space permits 1 Place the Triple Chassis in its permanent location It should be located within 10 ft 3 3 m of the UPS Make sure that the front of the unit is accessible 2 Connect the female end of the cable 940 1000A to the 9 pin male connector labeled To UPS on the front of the Triple Chassis 3 Connect the male end of the cable to the 9 pin female Computer Interface Port on the rear of the UPS 4 If UPS monitoring is to be used connect the required cable 940 0024 not supplied from the 9 pin monitoring port on the front of the Triple Chassis to an appropriate serial port on your computer or to another card 5 If additional power is needed see Power Consider ations on page 5 connect the optional power adapter output to the front of the Triple Chassis Installation Monitoring Optional Rackmount The Triple Chassis is designed to mount in a NetShelter installation enclosure or other 19 inch EIA 310 D using the hardware included with the Triple Chassis The Triple Chassis can be installed in the enclosure by following these steps 1 Peel the rubber feet from the bottom of the Triple Chassis 2 Attach a mounting bracket to each side of the Triple Chassis using 2 small flat head screws supplied and a 2 Phillips screwdriver Installation The mounting brackets can be attached at various positions along the side of the Triple
Download Pdf Manuals
Related Search