Morphy Richards 131000 water dispencer
Contents
1. 1 will illuminate and the Heat Icon 11 will extinguish indicating the reheat function can be activated Press the Start Stop Button to reheat Sound The audible signals from your Hot Water Dispenser can be turned on or off Press and hold the Temperature Button 4 for 2 seconds to switch the sounds on or off Standby Your Hot Water Dispenser will enter Standby Mode to save power 60 seconds after the end of the heating and dispense cycle The unit enters standby mode after 5 minutes of inactivity if a heat and dispense cycle hasn t been completed To wake the unit press any button or rotate the Water Volume Dial 2 The Hot Water Dispenser can be placed in standby mode by pressing the Start Stop Button 1 for 2 seconds Any water remaining in the Heating Chamber when your Hot Water Dispenser enters stand by will need to be dispensed upon exiting standby or reheated and dispensed before a new volume or temperature can be selected smart deas for your home 24 03 2014 09 06 FEES Didjomiceny The Drip Tray Indicator 10 indicates that the Drip Tray is full and must be emptied To empty pull the drip tray outwards until it is free from the runners and discard the contents CAUTION The contents of the drip tray may be hot Replace the Drip Tray once emptied ensuring the Drip Tray Cover 9 is replaced correctly DESCALE This product is fitted with a concealed element that must be descaled when the Descale2. Icon illuminates Excessive scale can cause the product to switch off before the end of the heating cycle and may damage the element invalidating the warranty Remove hard scale using a proprietary descaling product We recommend Oust Descaler please follow the instructions carefully which may be purchased from our Helpline or from your local retailer To descale the unit Remove the BRITA Hopper from the Water Tank and MAXTRA cartridge Fill the Water Tank to the MAX line with cold water add the Oust Descaler as per manufacturers instructions redefine KT131000 MUK REV3 indd 14 When the crystals have dissolved set the unit to heat 1 5 litres of water to 85 degrees Do not boil to 100 degrees Leave the Hot Water Dispenser for 10 minutes Do not dispense the water After 10 minutes dispense the water from the Heating Chamber into a vessel and discard Empty the water tank and rinse thoroughly with cold water Fill the water tank to the MAX line with cold water set the unit to boil 1 5 litres to 100 degrees and dispense the water Discard the water and repeat the cycle 3 times Replace the BRITA Hopper and MAXTRA cartridge into the Water Tank Fill with fresh water Press and hold the Start Stop Button 1 for 5 seconds to reset the descale timer The descale icon will extinguish The Hot Water Dispenser will reset and the unit will return to ready mode After 60 seconds of inactivity the Hot Water Dispense
3. filter cartridge or BRITA Memo please call BRITA Customer Care team on the telephone number below BRITA Helpline 0844 742 4800 Talk To Us If you have any questions or comments or want some great tips or recipe ideas to help you get the most out of your products join us online Blog www morphyrichards co uk blog Facebook facebook com morphyrichardsuk Twitter loveyourmorphy Website www morphyrichards com 12 redefine OWM We Veh KT131000 MUK REV3 indd 16 Le 24 03 2014 09 06 Registering your 2 year guarantee Your standard one year guarantee is extended for an additional 12 months when you register the product within 28 days of purchase with Morphy Richards If you do not register the product with Morphy Richards within 28 days your product is guaranteed for 1 year To validate your 2 year guarantee register with us online at www morphyrichards co uk Or call our customer registration line UK 0844 871 0962 IRE 1800 409 119 N B Each qualifying product needs to be registered with Morphy Richards individually Please note that the 2 year guarantee is only available in the UK and Ireland Please refer to the one year guarantee for more information Your 1 year guarantee It is important to retain the retailer s receipt as proof of purchase Staple your receipt to this back cover for future reference Please quote the following information if the product develops a fault These numbers can be found on the base of
4. the product Model no Serial no All Morphy Richards products are individually tested before leaving the factory In the unlikely event of any appliance proving to be faulty within 28 days of purchase it should be returned to the place of purchase for it to be replaced If the fault develops after 28 days and within 12 months of original purchase you should contact the Helpline number quoting Model number and Serial number on the product or write to Morphy Richards at the address shown You may be asked to return a copy of proof of purchase Subject to the exclusions set out below see Exclusions the faulty appliance will then be repaired or replaced as appropriate and dispatched usually within 7 working days of receipt If for any reason this item is replaced or repaired during the 1 year guarantee period the guarantee on the new item will be calculated from original purchase date Therefore it is vital to retain your original retailers receipt or invoice to indicate the date of initial purchase To qualify for the 1 year guarantee the appliance must have been used according to the instructions supplied For example crumb trays should have been emptied regularly IF YOU ARE HAVING A PROBLEM WITH ONE OF OUR PRODUCTS CALL OUR HELPLINE KT131000 MUK REV3 indd 17 E G BEERS Exclusions Morphy Richards shall not be liable to replace or repair the goods under the terms of the guarantee where 1 The fault has
5. 95 and 100 degrees By choosing the correct temperature for your drink not only will you create better tasting drinks you will also save time and energy too 85 C Green white and herbal teas powder based cold and flu remedies black instant coffee 95 C French press cafetiere coffee instant coffee with milk hot toddies malted milk hot chocolate 100 C Black teas e g darjeeling assam ceylon english breakfast and earl grey noodle pasta snacks instant soup type drinks Auto Manual DIKE The auto dispense feature allows you to automatically dispense volumes of water below 600ml For safety reasons it is not possible to automatically dispense volumes above 600ml Before heating press the Dispense Button 5 to switch the auto dispense feature on or off The Icon 14 will appear on the LCD Screen 3 when the feature is enabled After heating if the volume is above 600ml or if the auto dispense is turned off your Hot Water Dispenser will sound and the Dispense Button will Illu minate Press the Dispense Button to begin dispensing water from the Dispense Nozzles 6 NOTE All water must be dispensed before you can start the heating cycle again WEN iy 8 redefine Ti nat Bu ait ARRES KT131000 MUK REV3 indd 12 24 03 2014 09 06 Sy Multiple Cups Multiple cups can be filled quickly and easily by starting and stopping the dispense cycle and exchanging vessels 1 Set your Hot Water Di
6. ITA Hopper 21 To reset the BRITA Memo please press and hold down the Start Button on the Memo until all four bars appear in the display and flash twice The Cartridge Active Indicator Light in the bottom right corner of the BRITA Memo indicates that it is working After four weeks all four bars will disappear and a flashing arrow will indicate that the cartridge should now be changed After changing the cartridge reset the Memo Replacing the BRITA Memo The BRITA Memo 20 has a life of approximately 5 years To remove the exhausted BRITA Memo place a screwdriver in the notch next to the BRITA Memo and push it out Please note that BRITA Memo should not be removed for any other reason than to dispose of it More information on the use of BRITA filter cartridges and the BRITA Memo can be found in the BRITA information guide supplied with your hot water dispenser Telephone our replacement parts helpline 0844 873 0726 for your new BRITA Memo If you require assistance on using your BRITA MAXTRA filter cartridge or BRITA Memo please call BRITA Customer Care team on 0844 742 4800 APARIAR smart deas for your home j RARA GN 24 03 2014 09 06 Using the Hot Water Dispenser The following instructions detail the steps to follow to use your Hot Water Dispenser For Installation of the BRITA Filtration system see the previous page If required follow steps of 1 6 of Resetting the system see page 4 to reset t
7. Remove the Water Tank 7 from the Main Unit Remove the BRITA MAXTRA Cartridge 19 and BRITA Hopper 21 from the Water Tank Place a vessel underneath the Dispense Nozzles and press the Dispense Button 5 to reset the system This takes approx 25 seconds Any water dispensed during resetting should be discarded Press the Start Stop Button 1 the Hot Water Dispenser will pump 240ml of water into the heating chamber and start to heat AY N ities AKD yuni if fi if i i d fis om ae 1 A WUY e AA Bit fe VANNJA S iy ORTIS y Pili i KT131000 MUK REV3 indd 7 This quick start guide shows you the basic steps for dispensing 240ml of hot water for a single cup of tea or coffee This quick start guide does not detail the steps to use the BRITA Filtration System For more detailed information on using your new Hot Water Dispenser or BRITA Filtration System please read this instruction manual Fill the Water Tank with cold water and return to your Hot Water Dispenser Plug your Hot Water Dispenser into the electrical socket Using the Water Volume Dial 2 adjust the Dispense Volume 15 to 240ml Place a cup on the Drip Tray 8 under the Dispense Nozzles When heated the water will automatically dispense from the Dispense Nozzels 6 into your cup ne 24 03 2014 09 06 Resetting The System Plug your Hot Water Dispenser into the mains outlet and switch on at the socket Remove the Water Tank an
8. been caused or is attributable to accidental use misuse negligent use or used contrary to the manufacturer s recommendations or where the fault has been caused by power surges or damage caused in transit 2 The appliance has been used on a voltage supply other than that stamped on the products 3 Repairs have been attempted by persons other than our service staff or authorised dealer 4 The appliance has been used for hire purposes or non domestic use 5 The appliance is second hand 6 Morphy Richards reserves the right not to carry out any type of servicing under the guarantee at its discretion 7 Plastic filters for all Morphy Richards kettles and coffee makers are not covered by the guarantee 8 Batteries and damage from leakage are not covered by the guarantee This guarantee does not confer any rights other than those expressly set out above and does not cover any claims for consequential loss or damage This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer Morphy Richards products are intended for household use only See usage limitations within the location safety instructions DXEM Morphy Richards has a policy of continuous improvement in product quality and design The company therefore reserves the right to change the specification of it s models at any time For electrical products sold within the European Community At the end of the electrical pro
9. d fill with cold water Replace ensuring it is returned correctly into the Main Unit 23 If using the BRITA Filtration System refer to the set up guide on page 5 Place an empty vessel such as a measuring jug or saucepan underneath the Dispense Nozzles redefine ei ii Oh AN Be ai yay KT131000 MUK REVS3 indd 8 TE _ Before using your Hot Water Dispenser for the first time or after it has been unplugged from the mains You must perform the following steps to reset your Hot Water Dispensers heating chamber Your Hot Water Dispenser will not function if the system has not been reset If the Water Tank 7 is empty the Empty Tank Icon 12 will illuminate and flash START ei w The Dispense Button 5 will flash and the Dispense Icon 13 will appear on the screen Press the Dispense Button to reset the system Any remaining water will be dispensed from the system into the vessel below This takes approximately 25 seconds It is now ready for use 24 03 2014 09 06 RE BRITA filtration Filtering your water improves the taste and appearance of beverages by reducing limescale lead chlorine and other impurities The BRITA MAXTRA Filter Cartridge offers improved filtration due to MAXTRA Technology The natural MicroporeFilter in combination with the powerful Protect Filter reduces chlorine and limescale for a great natural taste and further reduces metals such as lead and copper Unique flow contr
10. ducts useful life it should not be disposed of with household waste Please recycle where facilities exist Check with your Local Authority or retailer for recycling advice in your country UK 0844 871 0960 EIRE 1800 409 119 SPARES 0844 873 0726 5 Viky EPA RIET x Ah Hain smart deas for your home AEN AAN WM i vi 24 03 2014 09 06 Mo ho LC D D l Below are some of the icons that may highlight IS D qy during use and their meaning Refer to the instruction book for more information on the W Glossary stings Water Tank 12 13 5 The Water Tank 7 is either empty or not properly fitted Fill the Water Tank and ensure the Water Tank is The system needs to be reset before use Follow the securley fitted to the Main Unit instructions under Resetting the System page 4 aL Lt mltr rt aL Li miltr S 100 Auto Dispense Heat Icon 14 Volumes between 150 600ml will be automatically 11 dispensed unless deselected by pressing the Dispense The Boil Icon remains lit while the water is within 5 C Button 5 Volumes above 600ml cannot automatically of the desired temperature If the water drops more be dispensed than 5 C then the icon will extinguish the Start Stop Button will illuminate and the water can be reheated by pressing the Start Stop Button Ai ml E Lt eet OD AN S Ate AUTO Water Still to Dispense Descale 16 13 Y
11. he system and then discard the water If the Hot Water Dispenser is in standby mode press any button to wake Place the required vessel cup pan pot etc under the Dispense Nozzles 6 One or two vessels can be filled at the same time during each dispense cycle provided they are the same size SFA ETEFT ARE E rA Before using your Hot Water Dispenser or if it has not been used for over a week follow these instructions to boil the maximum amount of water then discard to ensure the system is flushed through Filtering water through the BRITA Maxtra Cartridge takes around 4 minutes for 1 5L Ensure enough water has been filtered and is ready for use in the water tank before heating Pull out the Drip Tray 8 from the Main Unit if needed Adjust the temperature of the water by pressing the Temperature Button 4 to cycle through the options 85 95 amp 100 C The water temperature will be displayed on the screen WARNET E f Win ee AN ARANE A AAN o ii redefine 0 ONAA ALAN IA MRR a Ut F n iy EESAN j Vint Sif i TRAV KT131000 MUK REV3 indd 10 1p K Ma PEA ALA i TSAN AKEN 24 03 2014 09 06 Turn the Water Volume Dial 2 to adjust the Dispense Volume 15 Your Hot Water Dispenser can heat between 150ml to 1 5L of water per cycle Press the Start Stop Button 1 to begin heating Your Hot Water Dispenser will sound and the heat cycle will begin Once started the volume and temperature can o
12. nly be changed during the first few seconds of the heating cycle To pause the water flow whilst dispensing press either the Start Stop or the Dispense Button KT131000 MUK REV3 indd 11 l You can automatically dispense volumes of water at 600ml and below To turn this feature on or off press the Dispense Button 5 This function cannot be selected for volumes over 600ml These must be dispensed manually Once ready your Hot Water Dispenser will sound The hot water will be dispensed automatically If the manual dispense function has been selected press the Dispense Button 5 to begin dispensing To resume the water flow press the Dispense Button again NOTE You must dispense all water heated before you can start the heating cycle again smart deas for your home 24 03 2014 09 06 PEER Drinks Temperature Getting the correct water temperature is essential if you are to enjoy your favourite hot drinks with maximum flavour and taste E g If you re a green tea drinker then water that is brewed too hot will scorch the leaves creating a bitter taste Press the Temperature Button 4 to cycle through the options 85 95 amp 100 C The water temperature will be displayed on the screen 17 The guide below includes some of the most popular drinks to help you get the most from your Hot Water Dispenser Your Hot Water Dispenser has been pre programed with 3 of the most popular temperatures for drinks 85
13. ol ensures the perfect filtration time for best results For maximum filter performance and for optimum taste it is important to change your BRITA MAXTRA Filter Cartridge regularly BRITA recommends that you replace the cartridge every 4 weeks Using the BRITA filtration system is optional If you do not wish to use the filtration system simply remove the BRITA Hopper 21 and MAXTRA Filter Cartridge 19 from the Water Tank 7 Filtering water through the BRITA Filtration System takes roughly 4 minutes to filter 1 5L of water You can use the system while filtering providing enough water has filtered into the Water Tank Installing a BRITA MAXTRA Cartrige 1 Unwrap the BRITA MAXTRA Cartridge 19 and immerse in water gently shake to loosen any bubbles bo 2 Push the BRITA MAXTRA Cartridge into place in the BRITA Hopper 3 Place the BRITA Hopper into the Water Tank Before returning the Water Tank to the Main Unit fill the BRITA Hopper with Cold Water and allow the water to filter through the BRITA MAXTRA Cartridge Discard the filtered water Repeat this step twice KT131000 MUK REV3 indd 9 E O BEERNS 4 Fill the BRITA Hopper with fresh water and return the Water Tank to the main unit Your BRITA Cartridge is ready for use with your Hot Water Dispenser BRITA Memo The BRITA Memo 20 measures the recommended time of use of your MAXTRA Filter Cartridge 19 The BRITA Memo is located in the top of the BR
14. our Hot water Dispenser needs descaling Follow the There is still water remaining in the heating chamber instructions under Descaling to descale the heating Either reheat or dispense water before next use chamber page 10 KT131000 MUK REV3 indd 18 PS 24 03 2014 09 06
15. r will enter standby Cleaning Wipe the outside with a damp cloth WARNING Always disconnect the plug from the mains and allow the appliance to cool before cleaning IMPORTANT Do not use abrasive cleaners on the outside of the appliance as they may scratch the surface i UEN TEETE Ai a ile ie UA NE tin Vi Tat ih f WER Hi KA AS E 24 03 2014 09 06 RE E O Volume Guide Mugs and cups vary by size The measurement table We recommend measuring the volume of your below is a guide to volumes for different vessels vessels and noting it down for future use These will vary dependant upon your vessel size and requirements Vessel Capacity Vessel Capacity 150ml 180ml Cafeti re UP 750ml IL 300ml 360ml Teapot 230ml 300ml 180ml 380ml Noodle pot Gag g qeg 360ml 660ml 750ml 1 5ml TAA ay ia mie fii i _ smart deas for your home niy i Ay iy a i Nuh nik E f Wh tya AN AET H A RRN E L KT131000 MUK REV3 indd 15 24 03 2014 09 06 Contact Us Helpline if you are having a problem with your appliance please call our Helpline as we are more likely to be able to help than the store you purchased the item from Please have the product name model number and serial number to hand when you call to help us deal with your enquiry quicker UK Helpline 0844 871 0960 EIRE Helpline 1800 409 119 Spares 0844 873 0726 If you require assistance on using your BRITA MAXTRA
16. spenser unit to heat a desired amount of water with the Auto Dispense featue switched off Place two cups under the Dispense Nozzles 6 and dispense the water by pressing the Dispense Button 5 2 When the cups are filled press the Dispense Button again to stop the flow 3 Place another two empty cups under the Dispense Nozzles and repeat the process until all remaining water has been dispensed Dispense NOYZA ISS There are two Dispense Nozzles 6 on your Hot Water Dispenser These can be used to fill one or two cups at one time If dispensing into two vessels try to ensure they are of equal size and heat double the amount of water required for one Place your cups on the Drip Tray underneath the Dispense Nozzles Your Hot Water Dispenser will dispense an equal amount from each Nozzle KT131000 MUK REV3 indd 13 E G BEERS Cancel the heating cycle To cancel the heating cycle at any time press the Start Stop Button 1 Press either the Start Stop Button again to continue the current cycle or press the Dispense Button 5 to empty the water Once a heating cycle has begun the volume and temperature of the water can only be changed during the first few seconds of the heating cycle The Water in the heating chamber must be dispensed before a new volume can be selected Reheating Water Any water remaining in the heating chamber that has cooled down by 5 degrees can be reheated The Start Stop Button
Download Pdf Manuals
Related Search