Jou Jye Computer A 2424 computer case
Contents
1. User s Manual Table of Contents User s Manual Open Chassis Cover 1 Unscrew the two screws on the back of top cover 2 Slide the top cover backward about 4 inches 3 Remove the top cover from the chassis User s Manual Remove The Disk Drives Cage Full Set 1 Unscrew all 3 screws on the disk drives cage 2 Push the cage backward to disengage with the front chassis 3 Remove the cage User s Manual Remove The 3 5 Drive Cage HDD amp FDD 1 Unscrew the combined 3 5 Drive Cage by loosening 2 screws 2 Push the Drive Cage backward 3 Remove the Cage User s Manual Remove The 3 5 Hard Disk Drive Cage 1 Unscrew the HDD Cage by loosening 2 screws 2 Push the HDD Cage backward 3 Remove the HDD Cage User s Manual Install The Disk Drives 5 25 x 3 amp 3 5 x 3 1 Lift the Drive Cage full set from the main chassis body Refer to the corresponding section 2 Place the drives into the cage properly Secure each disk drive in the cage by at least 4 screws 2 screws at each side of drive is highly recommended 3 Unscrew the HDD Cage and place HDD in the Cage Secure the HDD by 4 screws 4 Unscrew the FDD Cage and place FDD in the Cage Secure the FDD by 4 screws User s Manual Install A Back plane The chassis is capable of fitting a standard ATX AT main board or a pas2. 2 41 173 2 88 470 177 TE 7 on o B gt o MENN W oS E o o B gt oO BEN WA SP 5 e gt et ce 431 8 3 C gt 482 6 User s Manual Exploded Diagram 1 Front Panel 9 5 25 Drive Bezel 17 Card Guide 7 slot 25 Air Filter Holder 2 Chassis 1013 5 Drive Bezel 18 Card Guide 3 slot 26 Air Filter 3 Top Cover 11 Main board Plate 19 Indicator Panel 27 Rubber Cushion 4 Front Panel Set 12 Back window ATX 20 Grounding Clip 28 Back window 12 slot 5 Drive Cage 13 PS 2 PSU Bracket 21 Front Panel Hinge 29 Back window 14 slot 6 Handle 14 Ventilation Bar 22 Card Retainer 30 Extended I O Bar 7 3 5 Drive Cage 15 Key lock Set 23 Fan Frame 31 Card Ho
3. lder Tab 8 Disk Drive Cage 16 Card Guide Frame 24 LED Lens 32 SPS Stopper
4. rear panel 3 The rear panel keyboard connector is built in the mother board or passive back plane This connector works at any time 4 The front panel keyboard connector works only if a keyboard convert cable was installed User s Manual Control Panel Indicators The Control Panel located on front panel comprises the LEDs for System Power LED HDD Status LED Fan Fail LED Thermal 1 LED Thermal 2 LED oe De User s Manual Install Remove A PS 2 Type Switching Power Supply There are 2 major types of power supply available for the chassis standard PS 2 switching power supply and PS 2 type mini redundant 1 1 power supply To install or remove the power supply unit please follow the steps 1 Screw or unscrew the 6 screws on the power supply unit 2 Place or remove the power supply unit User s Manual Install Remove A PS 2 Type Redundant Power Supply There are 2 models of PS 2 type mini redundant power supply TC 300R8 MR2 supported by the chassis To install or remove the power supply unit please follow the steps 1 Screw or unscrew the 6 screws on the power supply unit 2 Place or remove the power supply unit onto the chassis properly There are different types of bracket you ll need to install the power supply unit into the chassis TC 300R8 Redundant PS MR2 Redundant PSU N ET N User s Manual Install A Fan Thermal Detect Board Op
5. sive 14 slots back plane To install a back plane into the chassis please follow the steps 1 Be sure the chassis model is exactly for the back plane 2 Place the back plane on the chassis main board plate properly 3 Secure the back plane onto the chassis by using the available screw holes User s Manual Install An ATX Mother board The chassis is capable of fitting a standard ATX AT main board or a passive 14 slots back plane To install a ATX mother board into the chassis please follow the steps 1 Be sure the chassis model is exactly for the ATX mother board 2 Place the mother board on the chassis main board plate properly 3 Secure the mother board onto the chassis by using the available screw holes User s Manual Use The Hold down Card Retainer The chassis offers a special designed Hold down Card Retainer to avoid the add in cards bad contact with main board caused by external shocking or vibration during delivery or regular movement Select the position of the slot Loosen the screw on card retainer bar accordingly Slide the card holder tap to engage the top edge of the add on card a Tighten the screw The Card Retainer supports the add in card height between 90mm to 115mm User s Manual Attaching A Keyboard The AT type keyboard connector is located on the front panel as a standard unit You can also find another keyboard connector PS 2 or AT type on
6. tion ECR9400 series support IS F08 Fan Monitor Board to control up to 8 fans The IS F08 comprised with 2 thermal sensors and adjustable temperature settings to enable the fan according to the user defined temperature conditions To install the Fan Monitor Board please follow the steps Open chassis cover 2 Place and secure the IS F08 on the left side panel by 4 screws 3 Refer to the IS FO8 user s manual connect the power and fan cables as well as place the thermal sensors on to proper position User s Manual Change A New Air Filter Open the front panel l 2 Press the air filter holder clip and remove the fan holder 3 Remove and replace a new air filter 4 Put the air filter holder back to the proper position 5 Close the front panel User s Manual Change The Cooling Fan 9 OO Oy OY eS ee a Open the front panel Loosen two thumb screws on the fan holder Withdraw the whole fan holder module Disconnect the fan connector from the power supply connector Remove the air filter Refer to the corresponding section Unscrew 4 screws to remove the fan and replace by a new fan Install the air filter Refer to the corresponding section Connect the fan power connector Install the whole fan holder module into the chassis 10 Tighten the two thumb screws on the fan holder 11 Close the front panel User s Manual Measurements mm 92 92 92 9
Download Pdf Manuals
Related Search