User-Manual - Newegg.com
Contents
1. not apply if the product becomes unable to perform its intended 1 Press POWER and hold for 2 seconds to turn ON the TRAV LER Interface Box Wait until the function in any way as a result of the television signal provider making any changes in technology or service Interface Box finishes connecting to antenna RETURN AUTHORIZATION POLICY A Return Material Authorization RMA is reguired prior to returning any product to Winegard Company or Winegard Warranty Services under this warranty policy Please call our Technical Services Department at 800 788 4417 or send an e mail to warranty winegard com to obtain the RMA number Please furnish the date of purchase when reguest ing an RMA number Enclose the product in a prepaid package and write the RMA number in large clear letters on 2 Press ENTER and hold for 2 seconds or until the unit displays Enter User Menu Press SELECT to move the asterisk to Yes Press ENTER 3 Press SELECT to move the asterisk to INSTALLATION the outside of the package To avoid confusion or misunderstanding a shipment s without an RMA number s or an unauthorized return s will be refused and returned to Customer freight collect 4 Press ENTER You will be asked to provide a code to enter the Installation Menu WINEGARD COMPANY DOES NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES EXPRESS OR IMPLIED MADE BY ANY OTHER PERSON 5 Press ENTER 4 times to enter code 0000 ALL OTHER2. two long screws into the top two holes in the front of the Reflector 2 Slide one of the wedge shaped clamps onto each screw sticking out of the back of the Reflector 3 Thread a nut onto each screw just enough to keep the Black Plastic Bolt clamp from falling off 4 Set the SHAW DIRECT Reflector on the Skew Plate in Figure 3 by lining up the two anchor posts in the base of the Reflector with the two notches in the Skew Plate The Reflector should be installed so that the LNB Arm is at the bottom of this plate FIGURE 4 5 Carefully use the clamps on the back of the Reflector to hold the Reflector in place Skew Skew Plate Anchor FIGURE 3 P N Clamp Post Anchor Post Note Make sure that the thicker part of the clamp is to the outside of the Reflector FIGURE 5 Coax Cable 6 Once the top screws and clamps are in place Clamp install the lower screws and clamps 7 Tighten the nuts on all four screws Rev 4 09 INSTALLATION 3 SHAW DIRECT 8 With the Bracket mounted securely connect the four Coax Cables to the Mount as shown in Figure 6 WINEGARD MOBILE PRODUCTS LIMITED WARRANTY 9 Find the Cable Tie on the coax cables 2 YEARS PARTS 1 YEAR LABOR that you cun Sulit s the ied desi were FIGURE 6 Winegard Company warrants this product against defects in materials or workmanship for a period of two 2 years coax Cae clamp on ca 2 from the date of original purchase During year one 1 of such
3. WARRANTIES WHETHER EXPRESS IMPLIED OR STATUTORY INCLUDING WARRANTIES OF FIT NESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY ARE LIMITED TO THE TWO YEAR PERIOD OF THIS WARRANTY In states that do not allow limitations on implied warranties or the exclusion of limitation of incidental or consequential damages the above limitations or exclusions do not apply Some states do not allow limitations on how long an implied warranty lasts or the exclusion of limitation of incidental T or consequential damages so the above limitations or exclusions may not apply to you 8 Press SELECT to move to YES This warranty gives Customer specific legal rights Customer may also have other rights that may vary from state to state 6 From the Installation Menu 7 Press SELECT to move to Calibrate EL and Press ENTER 9 Press ENTER to start the elevation calibration procedure The LCD should now display Calibrate EL In Progress SATELLITE RECEIVER WARRANTY See manufacturer s limited warranty policy 10 After a few moments the IDU LCD will display On EL Hard Stop WS MOBWARREV2 Yes NO Rev 1 10 Visually examine the antenna to verify that the antenna is against the Hard Stop The antenna will be pointing as far up as it can go this is the Hard Stop DO NOT paint this antenna 11 Press SELECT once to move asterisk to Yes if antenna is on the Hard Stop AN Painting the TRAV LER anten na 12 Press ENTER
4. WINEGARD TRAV LER Automatic Multi Satellite TV Antenna SHAW DIRECT Model SKA 733 Reflector amp Bracket INSTALLATION MANUAL Made in the U S A Winegard Company 3000 Kirkwood St Burlington a 2000 319 754 0600 FAX 319 754 0787 www winegar Printed in U S A Winegard Company 2012 1 12 TRAV LERe SHAW DIRECT Reflector and Bracket Installation N Check to be sure that there is nothing above the TRAV LER antenna that might prevent it from raising You will need at least 40 of clearance above the TRAV LER mount to ensure that you have room to install the reflector Pay attention to these Pinch Points as the antenna raises NOTE Pinch Points are called out both for your safety and to protect the cables Ca bles will be damaged if installed incorrectly See pages 3 4 in this installation manual FIGURE 1 Raise Antenna There are two ways to raise the antenna automatic or manual each is explained below A Automatic Steps 1 7 explain how to use the TRAV LER Interface Box to raise the mount 1 Press POWER and hold for 2 seconds to turn ON the TRAV LER Interface Box Wait until the Interface Box finishes connecting to antenna The TRAV LER may enter the Search Routine after 10 seconds this is normal See NOTE Below 2 Press ENTER and hold for 2 seconds or until the unit displays Enter User Menu Press SELECT to move the asterisk to Yes Press ENTER 3 P
5. and the LCD will display Calibrate EL Success will void your warranty 13 Press and Hold POWER for 2 seconds to to stow the antenna INSTALLATION INSTALLATION 5 SHAW DIRECT NY WINEGARD Winegard Company 3000 Kirkwood Street Burlington IA 52601 319 754 0600 Fax 319 754 0787 www winegard com Printed in U S A 2012 Winegard Company 1 12 2452259 6
6. pproval of the service is at the sole discretion of Winegard Company Alternatively Customer may ship the product prepaid to Winegard Technical Services located at 3111 Kirkwood DO NOT over tighten this screw screws when you replace the clamp holding the Be Careful not to strip out the hole for the 5 16 inch N coax cables to the arm DO NOT use a power tool NOTE If the cable tie is missing install the clamp 14 from Street Burlington lowa 52601 Telephone 800 788 4417 Customer must return the product along with a brief descrip tion of the problem and provide Winegard Technical Services with Customer s name address and phone number Customer must also provide proof of purchase to verify the product is under warranty If the product is returned before the expiration of the warranty period Winegard Company will at its option either repair or replace the product This Limited Warranty does not apply if the product has been damaged deteriorates malfunctions or fails from im proper installation misuse abuse neglect accident tampering modification of the product as originally manufactured by Winegard in any manner whatsoever removing or defacing any serial number usage not in accordance with prod the end of the connectors Calibrate the Elevation Motor uct instructions or acts of nature such as damage caused by wind lightning ice or corrosive environments such as salt spray and acid rain This Limited Warranty also does
7. ress SELECT to move the asterisk to INSTALLATION 4 Press ENTER You will be asked to provide a code to enter the Installation Menu 5 Press ENTER 4 times to enter code 0000 6 Press SELECT to move the asterisk to RAISE ANTENNA Press ENTER Press SELECT to move the asterisk to Yes 7 Press ENTER The TRAV LER mount will raise up about half way NOTE If the TRAV LER enters the Search Routine and the TRAV LER mount raises more than 1 2 way be fore RAISE ANTENNA is selected See Step 6 the TRAV LER will hit its Upper Hard Stop and Motor Stall will appear This is Normal The Motor Stall means the TRAV LER is all the way up and the mount cannot raise any more There are two easy ways to clear the Motor Stall a Press ENTER the TRAV LER antenna will return to the Installation Menu OR b Press POWER the TRAV LER antenna will stow and turn OFF Restart at Step 1 INSTALLATION 2 Rev 4 09 B Manual 1 Unplug TRAV LER Interface 2 Remove the black plastic bolt from the back of the mount using a wrench 3 Insert a 1 4 inch socket extension into the auxiliary drive as shown in Figure 2 Turn auxiliary drive counter clockwise to raise the unit enough to install new reflector bracket N NOTE DO NOT USE A DRILL AS THIS WILL Auxiliary Drive DAMAGE THE TRAV LER ELECTRONICS FIGURE 2 Coax Cable Connections To Raise Unit turn Counterclockwise Install the Reflector 1 Insert the
8. warranty Winegard Company will also pay author tie Carefully screw this clamp to the front of the Lift Arm Coax ized labor costs to an authorized Winegard dealer to repair or replace defective products No warranty claim will be using the 5 16 inch screw provided See Figure 5 Connections honored unless at the time the claim is made Customer presents proof of purchase to an authorized Winegard dealer to locate the nearest authorized Winegard dealer contact Winegard Company 3000 Kirkwood Street Burlington lowa 52601 Telephone 800 288 8094 or visit www winegard com Customer must provide proof of purchase with a dated sales receipt for the Winegard product to verify the product is under warranty If the date of purchase cannot be veri fied the warranty period shall be considered to begin thirty 30 days after the date of manufacture If a defect in material or workmanship is discovered Customer may take the product to an authorized Winegard dealer for service Customer must provide proof of purchase to verify the product is under warranty If the product is brought to an authorized Winegard dealer for service prior to expiration of year one 1 of the warranty period and a defect in material or workmanship is verified by Winegard Technical Services Winegard Company will cover the Win egard dealer s labor charges for warranty service The Winegard dealer must contact Winegard Technical Services in advance for pre approval of the service A
Download Pdf Manuals
Related Search